Siemens SIPROTEC 7SD610 Manual page 392

Appendix
A.7 Settings
Addr. Parameter
2933 FAST Σ i SUPERV
2935A ΔI min
2941
ϕA
2942
ϕB
2943 I1>
2944 U1>
3401 AUTO RECLOSE
3402 CB? 1.TRIP
3403 T-RECLAIM
3403 T-RECLAIM
3404 T-BLOCK MC
3406 EV. FLT. RECOG.
3407 EV. FLT. MODE
3408 T-Start MONITOR
3409 CB TIME OUT
3410 T RemoteClose
3411A T-DEAD EXT.
3420 AR WITH DIFF
3421 AR w/ SOTF-O/C
3423 AR WITH I.TRIP
3424 AR w/ DTT
3425 AR w/ BackUpO/C
3430 AR TRIP 3pole
3431 DLC / RDT
3433 T-ACTION ADT
3434 T-MAX ADT
3435 ADT 1p allowed
3436 ADT CB? CLOSE
3437 ADT SynRequest
3438 T U-stable
3440 U-live>
3441 U-dead<
3450 1.AR: START
3451 1.AR: T-ACTION
3453 1.AR Tdead 1Flt
3454 1.AR Tdead 2Flt
392
Function C
Measurem.Superv ON
OFF
Measurem.Superv 1A 0.05 .. 1.00 A
5A 0.25 .. 5.00 A
Measurem.Superv 0 .. 359 °
Measurem.Superv 0 .. 359 °
Measurem.Superv 1A 0.05 .. 2.00 A
5A 0.25 .. 10.00 A
Measurem.Superv 2 .. 70 V
Auto Reclose OFF
ON
Auto Reclose YES
NO
Auto Reclose 0.50 .. 300.00 sec
Auto Reclose 0.50 .. 300.00 sec; 0
Auto Reclose 0.50 .. 300.00 sec; 0
Auto Reclose with PICKUP
with TRIP
Auto Reclose Stops AutoRecl
starts 3p AR
Auto Reclose 0.01 .. 300.00 sec
Auto Reclose 0.01 .. 300.00 sec
Auto Reclose 0.00 .. 300.00 sec; ∞
Auto Reclose 0.50 .. 300.00 sec; ∞
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose WITHOUT
DLC
Auto Reclose 0.01 .. 300.00 sec; ∞
Auto Reclose 0.50 .. 3000.00 sec
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose YES
NO
Auto Reclose 0.10 .. 30.00 sec
Auto Reclose 30 .. 90 V
Auto Reclose 2 .. 70 V
Auto Reclose YES
NO
Auto Reclose 0.01 .. 300.00 sec; ∞
Auto Reclose 0.01 .. 1800.00 sec; ∞
Auto Reclose 0.01 .. 1800.00 sec; ∞
Setting Options Default Setting
ON
0.10 A
0.50 A
200 °
340 °
0.05 A
0.25 A
20 V
ON
NO
3.00 sec
3.00 sec
1.00 sec
with TRIP
starts 3p AR
0.50 sec
3.00 sec
0.20 sec
∞ sec
YES
YES
YES
YES
YES
YES
WITHOUT
0.20 sec
5.00 sec
NO
NO
NO
0.10 sec
48 V
30 V
YES
0.20 sec
1.20 sec
1.20 sec
C53000-G1176-C145-6, Release date 02.2011
Comments
State of fast current summation
supervis
Min. current diff. for wire break
det.
Limit setting PhiA
Limit setting PhiB
Minimum value I1>
Minimum value U1>
Auto-Reclose Function
CB ready interrogation at 1st trip
Reclaim time after successful AR
cycle
Reclaim time after successful AR
cycle
AR blocking duration after
manual close
Evolving fault recognition
Evolving fault (during the dead
time)
AR start-signal monitoring time
Circuit Breaker (CB) Supervision
Time
Send delay for remote close
command
Maximum dead time extension
AR with differential protection ?
AR with switch-onto-fault over-
current ?
AR with intertrip ?
AR with direct transfer trip ?
AR with back-up overcurrent ?
3pole TRIP by AR
Dead Line Check / Reduced
Dead Time
Action time
Maximum dead time
1pole TRIP allowed
CB ready interrogation before re-
closing
Request for synchro-check after
3pole AR
Supervision time for dead/live
voltage
Voltage threshold for live line or
bus
Voltage threshold for dead line or
bus
Start of AR allowed in this cycle
Action time
Dead time after 1phase faults
Dead time after 2phase faults
SIPROTEC, 7SD610, Manual