Wireless Receivers; Identification Of Parts; Choosing A Mounting Location; Mounting The Receiver - Bentel Security Kyo 320 Installation Manual

Wireless Receivers

The VRX32-433 and VRX32-868 Re ce i ver (ac ces sory
item) will al low your system to ma na ge up to 32 Wi re -
less de tec tors (PIRs, Ma gne tic Con tacts, Smo ke de tec -
tors), and up to 16 Wi re less keys (Key Fobs).
Vec torRX-8 Re ce i ver ma na ges up to 8 Wi re less de tec -
tors (PIRs, Ma gne tic Con tacts, Smo ke de tec tors), and
up to 8 Wi re less keys (Key Fobs). Ple a se read this sec -
tion to get an ove rall view of the steps in vol ved in in stal -
ling the Re ce i vers.
The term "Re ce i ver or Vec torRX Re ce i ver" has been
used in the parts whe re the fun ctions and ope ra ting mo -
des are com mon to all Re ce i vers. Ho we ver, in parts
whe re the fun ctions and ope ra ting mo des dif fer, the re -
spec ti ve Re ce i ver has been spe ci fied.
n Identification of Parts
The fol lo wing Ta ble de scri bes the com po nents of the
Re ce i ver (see Fi gu re 8 - 7 - ).The num bers in bol dfa ce
in this sec tion, re fer to the de scrip tions in the Ta ble and
Fi gu re.
120 118
119
127
125
Fig ure 8 VectorRX-8 Re ceiver com po nents
118
120
119
125
125
122
Fig ure 7 VRX32-433 / VRX32-868 Re ce i ver com po -
nents
KYO320
128 120 118
124 122
118
120
119
125
125
RED BLK YEL GRN GND
124 123 127
No.
118 Spring catch slots (2)
119 An chor screw lo ca tions (3 x ø 4.6 mm)
120 An tennas (2)
121 Mi cro pro ces sors (2)
122 Seize microswitch
123 Tam per but ton
124 Screws (2)
125 Wire en try (10 x 6.4 mm)
126 Spring Catch
127 Ter mi nal board
128 PCB clip
n Choosing a Mounting Location
+
Mo unt the Re ce i ver and Wi re less De vi ces af ter the
pla ce ment tests.
Cho o se a pla ce that is:
Ø Dry
Ø Cen tral to the pro po sed pla ce ment of all Wi re less
De vi ces
Ø As clo se to the ce i ling as pos si ble
Ø Far from so ur ces of in ter fe ren ce such as: elec tri cal
no i se (com pu ters, te le vi sions, elec tric mo tors in ap -
plian ces, and he a ting and air-con di tio ning units),
and lar ge me tal ob jects (he a ting ducts and plum -
bing) which may shield the an ten nas.
Ensu re that no elec tri cal wi res run over the Re ce i ver
an ten nas. When mo un ting in a ba se ment, pla ce the
mo du le as high and as clo se to the un der si de of the first
flo or as pos si ble. The ran ge of the Re ce i ver will be re -
119
du ced if the unit is mo un ted be low ground level.
n Mounting the Receiver
When cho o sing the mo un ting lo ca tion en su re that the
mo un ting sur fa ce is flat, as une ven sur fa ces may im pa ir
pro per fun ctio ning of the Se i ze mi cro switch 124.
Read the fol lo wing in struc tions ca re fully be fo re mo un -
ting the Re ce i ver (re fer to the Fi gu re 8 - 7 - ).
1. Lo o sen the screws 124 (it is not ne ces sary to re mo -
ve them).
2. Press down on the tab 118 to re le a se the backpla te
from the frontpla te.
3. Lift the frontpla te up wards to a 90° an gle, then pull
the frontpla te away from the backpla te.
4. Pull the con nec tion wi res thro ugh the wire entry
125.
5. Pla ce the backpla te in the pro po sed pla ce ment,
mark the screw po si tions 119 then drill the screw
ho les.
!
Be ca re ful to avo id con du its and plum bing
when dril ling.
APPENDIX
DESCRIPTION
43