Tcp-Ip With Dial Back-Up Configuration - Ingenico 5100 Operating Manual

SKYZER TECHNOLOGIES

3.2.2 TCP-IP with Dial Back-up Configuration

PRIMARY PRIMARY PRIMARY PRIMARY
1.0
HOST IP ADDRESS HOST IP ADDRESS
HOST IP ADDRESS HOST IP ADDRESS
117.120.34.110 117.120.3 4.110
117.120.3 117.120.3 4.110 4.110
PRIMARY PRIMARY
2.0 PRIMARY PRIMARY
HOST PORT HOST PORT HOST PORT HOST PORT
33876 33876
33876 33876
SECONDARY SECONDARY
3.0 SECONDARY SECONDARY
HOST IP ADDRESS HOST IP ADDRESS HOST IP ADDRESS HOST IP ADDRESS
117.120.32 2 2 2 . . . . 110 117.120.3
117.120.3 117.120.3
SECONDARY SECONDARY
4.0 SECONDARY SECONDARY
HOST PORT HOST PORT HOST PORT HOST PORT
33876 33876 33876 33876
5.0
ENABLE DHCP Y/N ENABLE DHCP Y/N
ENABLE DHCP Y/N ENABLE DHCP Y/N
1 1 1 1 - - - - YES 2 YES 2- - - - NO YES 2 YES 2 NO NO NO
TERM IP ADDRESS TERM IP ADDRESS TERM IP ADDRESS TERM IP ADDRESS
6.0
XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX
7.0 SUBNET MASK SUBNET MASK SUBNET MASK SUBNET MASK
XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX
8.0 GATEWAY IP ADDR GATEWAY IP ADDR GATEWAY IP ADDR GATEWAY IP ADDR
XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX
9.0 QUICK DIAL? QUICK DIAL? QUICK DIAL? QUICK DIAL?
1 1 1 1 - - - - YES 2 YES 2- - - - NO NO
YES 2 YES 2 NO NO
INGENICO 5100 PAYMARK VERSION 6.0 OPERATING GUIDE
This parameter specifies the Primary Host IP Address. By default it is set to
117.120.34.110.
Press ENTER.
This parameter specifies the Primary TCP/IP Port Number of Paymark IP Host.
This parameter specifies the Secondary Host IP Address. By default, it is set to
117.120.32.110.
110
110 110
Press ENTER.
This parameter specifies the Secondary TCP/IP Port Number of Paymark IP Host.
Press the corresponding number key and press ENTER to set the IP address for the
terminal.
Option 1 – to allow the terminal to dynamically obtain its IP address and proceed
with step 7.0. Option 1 is the default value.
NOTE: When terminal is configured for DHCP, reboot the terminal by
pressing and releasing the shortcut keys (CHQ + SAV + CANCEL) at the
same time. This will enable the terminal to obtain the IP addresses from
the router.
Option 2 – to enter in static IP address for the terminal and proceed with step 4.0
NOTE: When configuring the terminal for Static IP address, ensure to
obtain the IP address, subnet mask and default gateway IP address from
your ISP (Internet Service Provider) for connectivity to Paymark network.
Enter in the static IP address for the terminal.
Example: 192.10.1.14
Note: Press the FUNC key to insert a dot in between numbers.
Enter in the subnet mask for the static IP address.
Example: 255.255.255.0
Enter in the gateway IP address to forward the packets from.
Example: 192.10.1.1
This parameter sets up the way that the terminal dials. Select the mode by pressing
the corresponding number key.
PAGE 28 OF 97
Version 1.3