J.2.2 Snmp Trap Linkage - Fujitsu PRIMEQUEST 2000 Series Administration Manual

Appendix J Systemwalker Centric Manager Linkage
For monitoring by duplicate MMBs in the PRIMEQUEST 2000 series server with Systemwalker, be sure to
register two MMB nodes and monitor these two nodes.
See the manual of Systemwalker Centric Manager about how to register the MMB nodes for the
PRIMEQUEST 2000 series.

J.2.2 SNMP trap linkage

This section provides an overview of SNMP trap linkage and describes the conversion definition procedure.
Process overview
Define conversion to convert SNMP traps from the PRIMEQUEST 2000 series server into messages that can
be read and understood by the monitoring operator. Converted message text is displayed on the
Systemwalker console.
Remarks
To ensure that converted text can be identified as a message from the PRIMEQUEST 2000 series server, the
keyword
[PRIMEQUEST] is embedded in the text.
Example: A SNMP trap from the PRIMEQUEST 2000 series server is converted and displayed.
[PRIMEQUEST] FileServer E 14002 SB#0-DIMM#0A0 DIMM: Uncorrectable ¥
ECC Part-no=0x0101 Serial-no=5023
The ¥ at the end of a line indicates that there is no line feed.
Note that to receive SNMP traps, the operations management server must be registered as the SNMP trap
destination in the PRIMEQUEST 2000 series server.
For details on how to set an SNMP trap destination, see the following manuals:
- 6.5.2 Configuring SNMP in the PRIMEQUEST 2000 Series Installation Manual (CA92344-0536)
- 1.5.6 [SNMP Configuration] menu in the PRIMEQUEST 2000 Series Tool Reference (CA92344-0539)
SNMP trap linkage procedure
1. Place the prepared TrapMSG conversion definition file, described in
in a directory on the operations management server.
2. Execute the prepared SNMP trap conversion definition application command, described in
Files and tools to
tools to prepare) into Systemwalker (to run on the operations management server).
Move to the command installation directory. Execute the following command. Example of execution on
the operations management server (Linux):
./CNSetCnfMg.exe –f <TrapMSG conversion definition file name (full
pathname)> -c
3. To represent the OID used in trap conversion as characters, use the MIB extended manipulation function
of Systemwalker to register the prepared extended MIB file (for traps), described in
tools to prepare, in Systemwalker. (Use the Systemwalker console screen for the operations
management client.) For details, see the manual of Systemwalker Centric Manager.
4. Apply the TrapMSG definition file to Systemwalker by performing the following step.
For details, see the manual of Systemwalker Centric Manager.
Remarks
- When the TestTrap function is used to confirm trap reception in the MMB Web-UI, the Test Trap message
will appear on the Systemwalker console screen. In this case, the target MMB node enters the problem
status on the console screen. For how to return it to the normal status, see the manual of Systemwalker
Centric Manager.
- If modifying the filtering definition to output Info-level messages (Panic/Stop Error), see the manual of
Systemwalker Centric Manager.
To display the TestTrap message on the console screen, the event filtering definition described in
Event monitoring linkage
For details on the TestTrap function, see the following manuals:
- 6.5.2 Configuring SNMP in the PRIMEQUEST 2000 Series Installation Manual (CA92344-0536)
- 1.5.6 [SNMP Configuration] menu in the PRIMEQUEST 2000 Series Tool Reference (CA92344-0539)
prepare, to include the TrapMSG conversion definition file (see
must be applied in advance.
434
TABLE J.1 Files and tools to
TABLE J.1
TABLE J.1 Files and
TABLE J.1 Files and
CA92344-0537-08
prepare,
J.2.3