Fujitsu PRIMEQUEST 2000 Series Administration Manual page 305

Hide thumbs Also See for PRIMEQUEST 2000 Series:
Table of Contents

Advertisement

CHAPTER 7 PCI Card Hot Maintenance in SUSE Linux Enterprise Server 12
7.7 Hot Replacement of PCI Express Cards
1. Perform the work for suppressing access to the iSCSI connection interface.
a. Confirm the state of multiple path by DM-MP (*1) or EMPD (*2).
b. Use the iscsiadm command to log out from the path (iqn) through which the iSCSI card to be replaced
is routed, and disconnect the session.
Example which confirms the state of session before disconnecting:
# /sbin/iscsiadm -m session
tcp: [1] 192.168.1.64:3260,1 iqn.2000-
09.com.fujitsu:storage-system.eternus-
dx400:00001049.cm0ca0p0
tcp: [2] 192.168.2.66:3260,3 iqn.2000-
09.com.fujitsu:storage-system.eternus-
dx400:00001049.cm1ca0p0
Example which logout path going through a NIC to be replaced:
# /sbin/iscsiadm -m node -T iqn.2000-09.com.fujitsu:storage-
system.eternus-dx400:00001049.cm1ca0p0 -p 192.168.2.66:3260
–-logout
c. Use the iscsiadm command to confirm that the target session has been disconnected.
Example which confirms the state of session after disconnecting
# /sbin/iscsiadm -m session
tcp: [1] 192.168.1.64:3260,1 iqn.2000-
09.com.fujitsu:storage-system.eternus-
dx400:00001049.cm0ca0p0
d. You can confirm the disconnection of sessions on multipath products using DM-MP or ETERNUS
multidriver.
*1: Write down the DM-MP display contents at the session disconnection.
Example of DM-MP display before disconnecting path
# /sbin/multipath -ll
mpath1 (36000b5d0006a0000006a104900000000) dm-0
FUJITSU,ETERNUS_DX400
[size=50G][features=0][hwhandler=0][rw]
¥_ round-robin 0 [prio=2][active]
¥_ 3:0:0:0 sdb 8:16
¥_ 4:0:0:0 sdc 8:32
Example of DM-MP display after disconnecting path
# /sbin/multipath -ll
mpath1 (36000b5d0006a0000006a104900000000) dm-0
FUJITSU,ETERNUS_DX400
[size=50G][features=0][hwhandler=0][rw]
¥_ round-robin 0 [prio=1][enabled]
¥_ 3:0:0:0 sdb 8:16
*2: See the ETERNUS Multipath Driver User's Guide (For Linux).
Work to be performed after NIC replacement
For iSCSI (NIC) hot replacement, be sure to follow the procedure below when Step 18 of the NIC
replacement procedure in
1. To restore access to the iSCSI connection interface, perform the following.
a. Confirm the state of multiple path by DM-MP (*1) or EMPD (*2).
b. Use the iscsiadm command to log in to the path (iqn) through which the replacement iSCSI card is
routed, and reconnect the session.
Example which confirms the state of session before connecting:
# /sbin/iscsiadm -m session
tcp: [1] 192.168.1.64:3260,1 iqn.2000-
09.com.fujitsu:storage-system.eternus-
dx400:00001049.cm0ca0p0
Example which login path going through a NIC to be replaced:
[active][ready]
[active][ready]
[active][ready]
7.1.4 Network card replacement
279
procedure.
CA92344-0537-08

Advertisement

Table of Contents
loading

Table of Contents