Omron VARISPEED L7 Manual page 145

Name
Param-
eter
Num-
Display
ber
ASR output
without filter
U1-44
ASR Out w/o Fil
Feed forward
control output
U1-45
FF Cout Output
Slip compensa-
tion value
U1-50
Slip comp value
Max Current
during accelera-
tion
U1-51
MaxCur-
rent@Acc
Max Current
during decelera-
tion
U1-52
5
MaxCur-
rent@Dec
Max Current
during Top
speed
U1-53
MaxCur-
retn@Run
Max Current
during leveling
speed
U1-54
Max Amp
at Vl sped
Number of trav-
els
U1-55
No of travels
AI-14B channel
1 input level
U1-56
*1
AI-14 Ch1
InpLvl
Car acceleration
rate
U1-57
Cage accel
q-axis motor
current refer-
U1-74
ence
Iq Reference
d-axis motor
current refer-
U1-75
ence
Id Reference
*1. The parameter is displayed only if a AI-14B option board is installed.
58
5-
Description
Multi-Function Analog Output
Monitors the output from the
10 V: Rated secondary cur-
speed control loop (i.e., the pri-
rent of motor
mary filter input value). 100%
(-10 V to 10 V)
is displayed for rated second-
ary current of the motor.
Monitors the output from feed
10 V: Rated secondary cur-
forward control. 100% is dis-
rent of motor
played for rated secondary cur-
(-10 V to 10 V)
rent of the motor.
Monitors the slip compensation
value.100% is displayed 10 V: Rated slip of motor
for rated slip (-10 V to 10 V)
Monitors the maximum current 10 V: Rated current of motor
during acceleration. (0 V to 10 V)
Monitors the maximum current 10 V: Rated current of motor
during deceleration. (0 V to 10 V)
Monitors the maximum current 10 V: Rated current of motor
at top speed. (0 V to 10 V)
Monitors the maximum current 10 V: Rated current of motor
at Vl speed. (0 V to 10 V)
Monitors the lift operation
counter.
(Cannot be output.)
Using parameter O2-15 the
counter can be cleared.
Monitors the input level of ana-
log input 1 on a AI-14B option 10 V: 100%
board. A value of 100% is equal (-10 to 10 V)
to 10V input.
Shows the elevator car acceler- 10V: 9.8 m/s²
ation rate value. (-10V to 10 V)
Monitors the q-axis current ref- 10 V: Motor rated current
erence. (-10 to 10 V)
Monitors the d-axis current ref- 10 V: Motor rated current
erence. (-10 to 10 V)
Output Signal Level During Min.
Unit
0.01%
0.01%
0.01%
0.1 A
0.1 A
0.1 A
0.1 A
-
0.1%
0.01
m/s²
0.1%
0.1%
Control Methods
MEMO-
Closed
Open Closed
BUS
Loop
V/f Loop Loop
Register
Vector
Vector Vector
(PM)
- - A A 6BH
- - A A 6CH
A A - - 71H
A A A A 72H
A A A A 73H
A A A A 74H
A A A A 75H
A A A A 76H
A A A A 77H
A A A A 57H
A A A A 7C6H
A A A A 7C7H