Omron VARISPEED L7 Manual page 144

Name
Param-
eter
Num-
Display
ber
Frequency refer- Monitors the frequency refer-
ence after soft- ence after the soft starter.
starter This frequency value does not
U1-20
include compensations, such as
slip compensation.
SFS Output
The unit is set in o1-03.
Monitors the input to the speed
ASR input
control loop.
U1-21
The maximum frequency corre-
ASR Input
sponds to 100%.
Monitors the output from the
ASR output
speed control loop.
U1-22
The maximum frequency corre-
ASR output
sponds to 100%.
Monitors the reference value
DI-16H2 input
from a DI-16H2 Digital Refer-
status
ence Card.
U1-25
The value will be displayed in
binary or BCD depending on
DI-16 Reference
user constant F3-01.
Output voltage
Monitors the Inverter internal
reference (Vq)
U1-26 voltage reference for motor sec-
ondary current control.
Voltage Ref(Vq)
Output voltage
Monitors the Inverter internal
reference (Vd)
U1-27 voltage reference for motor
excitation current control.
Voltage Ref(Vd)
Software No.
(Manufacturer's CPU software
(CPU)
U1-28
No.)
CPU ID
ACR output of q
Monitors the current control
axis
U1-32 output value for the motor sec-
ACR(q)
ondary current.
Output
ACR output of d
Monitors the current control
axis
U1-33 output value for the motor exci-
tation current.
ACR(d) axis
OPE fault
Shows the first parameter num-
parameter
U1-34 ber when an OPE fault is
detected.
OPE Detected
Zero servo
Shows the number of PG pulses
movement
of the movement range when
pulses
U1-35 zero servo was activated. The
shown value is the actual pulse
Zero Servo
number times 4.
Pulse
Cooling fan
Monitors the total operating
operating time
time of the cooling fan. The
U1-40
time can be set in
FAN Elapsed
02-10.
Time
Inverter Heat-
Shows the inverter heatsink
sink Tempera-
temperature measured by the
U1-41
ture
IGBT thermal protection sen-
sor.
Actual Fin Temp
Output Signal Level During
Description
Multi-Function Analog Output
10 V: Max. frequency
(0 to ± 10 V possible)
10 V: Max. frequency
(0 to ± 10 V possible)
10 V:Max. frequency
(0 to ± 10 V possible)
(Cannot be output.)
10 V: 200 VAC (400 VAC)
(0 to ± 10 V possible)
10 V: 200 VAC (400 VAC)
(0 to ± 10 V possible)
(Cannot be output.)
10 V: 100%
(0 to ± 10 V possible)
10 V: 100%
(0 to ± 10 V possible)
(Cannot be output.)
(Cannot be output.)
(Cannot be output.)
(Cannot be output)
Control Methods
Closed
Min.
Open Closed
Loop
Unit
V/f Loop Loop
Vector
Vector Vector
(PM)
0.01H
A A A
z
0.01% - - -
0.01% - - A
0.01% - - A
- A A A
0.1 V - A A
0.1 V - A A
- A A A
0.1
- A A
%
0.1
- A A
%
- A A A
- - - A
1
A A A
hr.
°C A A A
MEMO-
BUS
Register
-
53H
A
A 54H
A 55H
58H
A
A 59H
5
A 5AH
A 5BH
A 5FH
A 60H
A 61H
A 62H
A 67H
A 68H
57
5-