Omron K3HB-C User Manual page 176

■ K3HB-P
Power ON
L p
Protect level
L +
RUN.PT:
run.pt L E V E L
RUN/adjustment protect
3 s min.
0
0 to 2
M
<
SET.PT:
set.pt
Setting level protect
1
0 to 2
L +
M
<
M
L E V E L
WT.PT:
wt.pt
MODE
Setting change protect
1 s min.
off
OFF,ON
M
<
MM.PT:
mm.pt
MAX/MIN protect
0
0 to 2
Adjustment level
Parameter Display
: Always displayed regardless of model or settings.
:
Displayed only for certain models or settings.
Press the @ [LEVEL] key for at least 1 s from
any display (except for the protect level) to
return to the first parameter in the RUN or
initial setting level.
RUN level
Measurement value
M
Comparative set value HH
MODE
99999
0 to 99999
M
<
Measurement
Measurement value
stops
Comparative set value H
99999
0 to 99999
M
<
M Measurement value
M
MODE MODE
Comparative set value L Measurement
0
0 to 99999 starts
M
<
Measurement value
Comparative set value LL
0
0 to 99999
L
L E V E L
1 s max.
L a
bank
BANK: Bank
0 to 7
0
* Displayed when bank
selection (bnk-c) is
M set to KEY.
MODE
cmwt CMWT:
Communications write
off
OFF, ON
*Displayed only for
Communications Units.
Advanced function setting level
L 0
L
L E V E L
FUNC:
func
3 s min.
Function
f1
F1 to F6
M
<
IN-TA:
in-ta
Input type A
00 No contact (NO/NC)
M
Contact (NO/NC)
<
IN-TB:
in-tb
Input type B
00
No contact (NO/NC)
M M
Contact (NO/NC)
<
L MODE
ps.ax PS.AX:
L E V E L
Prescale AX
1.0000
1 s min.
0.0000 to 9.9999
M
<
PS.AY:
ps.ay
Prescale AY
10 0
9 to 9
M
<
* This is not displayed in the factory default state.
Change the setting level protection to "0".
L
Password:
L E V E L
0169
1 s min.
L f
INIT: Set value initialization
init
OFF, ON
off
M
<
pass PASS: PASS output change LL,
L, PASS, H, HH, ERR
pass
M
<
OFF-D: Output OFF-delay 0 to
1,999 ms
SHOT: Shot output 0 to 1,999 ms
OUT-N:
Output de-energization
N-O, N-C
O-STP: Output refresh stop
o-stp
OFF, OUT, ALL
off
BNK-C: Bank selection
OFF, KEY, EV
STDBY:
stdby
Standby sequence
off
OFF, ON
About Parameters
TIME:
time
OFF, min, h:min:s,
L E V E L
off
min:s, 100 ms
M 1 s max.
<
dp DP: Decimal point
position 0 to 4
00000
M
<
OUT-P:
out-p
Comparative output pattern
Standard output,
nomal
zone output,level output
M
<
AMOV:
* amoV
Move to advanced
0
function setting level
19,999 to 99,999
L
L E V E L
1 s max.
Output test level L t
test
TEST: Test input OFF
0 to 99,999
off
L
L E V E L
Displayed only for
1 s max.
Communications
Communications
L 6
Units.
setting level
U-NO:
u-no
Communications
1
Unit No. 0 to 99
M
<
BPS: Baud rate
bps
9.6, 19.2, or
9 . 6
38.4 kbps
M
<
LEN:
len
Data length
7
7 or 8 bits
M
<
SBIT:
M
sbit
MODE Stop bits
2
1 or 2 bits
M
<
prty PRTY:
Parity
eVen
None, even, or odd
M
<
sdwt SDWT:
Send wait time
20
0 to 99 ms
L
L E V E L
Displayed for Linear
L 5
Linear output level Output Units only.
LSET.C: Linear
lset.c
current model
4-20 0 to 20 mA,
4 to 20 mA
M
<
LSET.V: Linear
lset.
voltage model
1-5
0 to 5 V, 1 to 5 V,
M
0 to 10 V
<
M
lset.h LSET.H: Linear
MODE
output upper limit
99999
0 to 99999
M
<
LSET.L: Linear
lset.l
output lower limit
0
0 to 99999
A-25
L