Omron K3HB-C User Manual page 178

■ K3HB-C
Power ON
L p
Protect level
L +
RUN.PT:
run.pt
L E V E L
RUN/adjustment protect
0 3 s min.
0 to 2
M
<
set.pt SET.PT:
Setting level protect
1
0 to 2
M
L +
<
M
L E V E L
wt.pt
MODE
WT.PT:
1 s min.
Setting change protect
off
M
OFF,ON
<
mm.pt
MM.PT:
0
MAX/MIN protect
0 to 2
Adjustment level
Parameter Display
:
Always displayed regardless of model or settings.
:
Displayed only for certain models or settings.
Press the @ [LEVEL] key for at least 1 s from
any display (except for the protect level) to
return to the first parameter in the RUN or
initial setting level.
RUN level
Measurement value
M
Comparative set value 5
MODE
99999
19,999 to 99,999
M
Measurement
Measurement value
stops
Comparative set value 4
99999
19,999 to 99,999
M
Measurement value
M
M
MODE
Comparative set value 3
MODE Measurement
99999
19,999 to 99,999
starts
M
Measurement value
Comparative set value 2
99999
19,999 to 99,999
M
Measurement value
Comparative set value 1
99999
19,999 to 99,999
L
L E V E L
1 s max.
L a
bank BANK: Bank
0 to 7
0
* Displayed when bank
selection (bnk-c) is
M
set to KEY.
MODE
cmwt
CMWT:
Communications write
off
OFF, ON
*Displayed only for
Communications Units.
Advanced function setting
level
Initial setting level L 0
L
L E V E L FUNC:
func
3 s min. Function
f3
F1 to F3
M
<
IN-TA:
in-ta
Input type A
00
No contact (NO/NC)
M
< Contact (NO/NC)
in-tb IN-TB:
Input type B
00
No contact (NO/NC)
M
<
M
L
Contact (NO/NC)
MODE
ps.ax
L E V E L
PS.AX:
1 s min.
1.0000
Prescale AX
M
0.0000 to 9.9999
<
ps.ay
PS.AY:
Prescale AY
10 0
9 to 9
M
<
L
Password:
L E V E L
0169
1 s min.
L f
INIT:
init
Set value initialization
off
OFF, ON
M
<
OFF-D: Output OFF-
delay 0 to 1,999 ms
SHOT: Shot output 0
to 1,999 ms
M
OUT-N:
MODE
Output de-energization
N-O, N-C
BNK-C: Bank selection
bnk-c
OFF, KEY, EV
Linear output level
About Parameters
DP:
dp
Decimal point position
L
00000
0 to 4
L E V E L
M
*Displayed when bank
1 s max.
selection (bnk-c) is
set to OFF.
<
OUT-P:
out-p
Comparative output
leVel
pattern, zone output,
M
< level output
amoV AMOV:
Move to advanced
0
function setting level
19,999 to 99,999
*This is not displayed
in the factory default
state. Change the
setting level
protection to "0".
L
L E V E L
1 s max.
Output test level
L t
TEST:
test
Test input
off
OFF, 19,999 to 99,999
L
L E V E L
Displayed only for
1 s max.
Communications
Communications
L 6
Units.
setting level
U-NO:
u-no
Communications
1
Unit No. 0 to 99
M
<
BPS: Baud rate
bps
9.6, 19.2, or
9 . 6
38.4 kbps
M
<
LEN:
len
Data length
7
7 or 8 bits
M
<
SBIT:
M
sbit
MODE Stop bits
2
1 or 2 bits
M
<
PRTY:
prty
Parity
eVen
None, even, or odd
M
<
SDWT:
sdwt
Send wait time
20
0 to 99 ms
L
L E V E L
Displayed for Linear
Output Units only.
L 5
LSET.C: Linear
lset . c
current model
0 to 20 mA,
4-20
4 to 20 mA
M
<
LSET.V: Linear
lset.V
voltage model
1-5 0 to 5 V, 1 to 5 V,
M 0 to 10 V
<
M
LSET.H: Linear
lset.h
MODE
output upper limit
99999
19,999 to 99,999
M
<
LSET.L: Linear
lset.l
output lower limit
:9999
19,999 to 99,999
A-27