Omron K3HB-C User Manual page 155

Appendices
K3HB-P
Display range 19,999 to 99,999
Measurement accuracy ±0.08% rdg ±1 digit (for voltage pulse/open collector sensors)
(at 23±5 C)
Measurement range Functions F1, F3, and F4:10 ms to 3,200 s
Function F2:
Functions F5 and F6:
Input signals • No-voltage contact (30 Hz max. with ON/OFF pulse width of 15 ms min.)
• Voltage
pulse
• Open
collector
Connectable sensors ON residual voltage: 3 V max.
OFF leakage current: 1.5 mA max.
Load current:
Comparative output re- 2 ms max. (time until the comparative output is made when there is a forced sudden change in the
sponse time (transistor input signal from 15% to 95% or 95% to 15%)
output)
Linear output response 10 ms max. (time until the final analog output value is reached when there is a forced sudden change
time in the input signal from 15% to 95% or 95% to 15%)
Insulation resistance 20 M min. (at 500 VDC)
Dielectric strength 2,300 VAC for 1 min between external terminals and case
Noise immunity 100 to 240 VAC models:
24 VAC/VDC models:
Vibration resistance
Frequency: 10 to 55 Hz; Acceleration: 50 m/s
Shock resistance
150 m/s
Weight Approx. 300 g (Base Unit only)
Degree of Front panel Conforms to NEMA 4X for indoor use (equivalent to IP66)
protection
Rear case IP20
Terminals IP00 + finger protection (VDE0106/100)
Memory protection EEPROM (non-volatile memory)
Number of rewrites: 100,000
Applicable standards UL61010C-1, CSA C22.2 No. 1010.1 (evaluated by UL)
EN61010-1 (IEC61010-1): Pollution degree 2/Overvoltage category II
EN61326: 1997, A1: 1998, A2: 2001
EMC EMI: EN61326+A1 industrial applications
Electromagnetic radiation interference
Terminal interference voltage
EMS: EN61326+A1 industrial applications
Electrostatic Discharge Immunity
Radiated Electromagnetic Field Immunity
Electrical Fast Transient/Burst Immunity
Surge Immunity
Conducted Disturbance Immunity
Power Frequency Magnetic Immunity
Voltage Dips and Interruptions Immunity
A-4
20 ms to 3,200 s
0 to 4 gigacounts
Mode Input frequency
range
F1 to F4 0 to 50 kHz
F5, F6 0 to 30 kHz
Mode Input frequency
range
F1 to F4 0 to 50 kHz
F5, F6 0 to 30 kHz
Must have a switching capacity of 20 mA or higher.
Must be able to properly switch load currents of 5 mA or less.
1,500 V at power supply terminals in normal or common mode
(waveform with 1-ns rising edge and pulse width of 1 s/100 ns)
1,500 V at power supply terminals in normal or common mode
(waveform with 1-ns rising edge and pulse width of 1 s/100 ns)
2 2
(100 m/s for relay outputs) 3 times each in 3 axes, 6 directions
CISPR 11 Group 1, Class A: CISPRL16-1/-2
CISPR 11 Group 1, Class A: CISPRL16-1/-2
EN61000-4-2: 4 kV (contact), 8 kV (in air)
EN61000-4-3: 10 V/m 1 kHz sine wave amplitude modulation (80 MHz to 1 GHz, 1.4GHz to 2 GHz)
EN61000-4-4: 2 kV (power line), 1 kV (I/O signal line)
EN61000-4-5: 1 kV with line (power line), 2 kV with ground (power line)
EN61000-4-6: 3 V (0.15 to 80 MHz)
EN61000-4-8: 30 A/m (50 Hz) continuous time
EN61000-4-11: 0.5 cycle, 0 /180 100% (rated voltage)
ON/OFF ON voltage OFF voltage
pulse width
9 s min. 4.5 to 30 V 30 to 2 V
16 s min.
ON/OFF Note: The Digital Time Interval Indicator
pulse width will malfunction if a pulse greater
than the input frequency range is
9 s min.
input. SYSERR may appear on
16 s min. the display.
2
, 10 sweeps of 5 min each in X, Y, and Z directions
Input
impedance
10 k