Omron E5AK PROGRAMMABLE TYPE User Manual page 151

Parameter No.
57 Input type
59 Scaling upper limit
58 Scaling lower limit
60 Decimal point
30 _C/_F selection
61 Control output 1 assignment
62 Control output 2 assignment
63 Auxiliary output 1 assignment
64 Auxiliary output 2 assignment
65 Alarm 1 type
66 Alarm 1 open in alarm
67 Alarm 2 type
68 Alarm 2 open in alarm
69 Alarm 3 type
70 Alarm 3 open in alarm
71 Direct/Reverse operation
28 Set point upper limit *1
27 Set point lower limit *1
72 PID / ON/OFF
35
α
85 AT calculated gain
36 Automatic return of display mode
93 AT hysteresis
55 LBA detection width
77 Event input assignment 3
78 Event input assignment 4
79 Transfer output type
81 Transfer output upper limit
80 Transfer output lower limit
82 HBA latch
89 Travel time
38 PV dead band
*7 See page 5-31.
*8 0: Control output (heat), 1: Control output (cool), 2 to 4: Alarms 1 to 3, 5: HBA, 6: LBA, 7 and 8: Errors 1 to 2, 10 to 11: Time
signal 1 to 2, 12: Program end, 13: Stage output
*9 See page 5-37.
*10 During temperature input, the range becomes the range of use of the selected sensor instead of the scaling upper/lower limit
values.
*11 -1: No specification, 0: Run/Reset, 1: Remote/Local, 2: Auto/Manual, 4: Hold/Hold cancel, 5: Advance, 6 to 8: Pattern select 0 to 2
*12 The following table shows the output ranges of the transfer output lower and upper limits.
Transfer Output Type
0: Present SP
2: Process value
3: Manipulated variable (heat)
4: Manipulated variable (cool)
5: Valve opening
Parameter
Transfer Output Lower Limit to
Transfer Output Upper Limit
-5.0 to 105.0% (standard control),
0.0 to 105.0% (heating and cooling control)
6.4 Commands and Responses
Data Setting Range
0 to 21
Scaling lower limit +1 to 9999
-1999 to scaling upper limit -1
0 to 3
0: _C, 1: _F
0 to 6, 10 to 13
0 to 6, 10 to 13
2 to 8, 10 to 13
2 to 8, 10 to 13
1 to 11
0: Closed in alarm, 1: Open in alarm
1 to 11
0: Closed in alarm, 1: Open in alarm
1 to 11
0: Closed in alarm, 1: Open in alarm
0: Reverse operation, 1: Direct operation
Set point lower limit +1 to scaling upper limit
Scaling lower limit to Set point upper limit -1
0: Advanced PID, 1: ON/OFF
0.00 to 1.00
0.1 to 10.0
0 to 99
0.1 to 9.9
0.0 to 999.9
-1 to 2, 4 to 8
-1 to 2, 4 to 8
0 to 5
0: OFF, 1: ON
1 to 999
0 to 9999
-1999 to 9999
-1999 to 9999
0.0 to 105.0%
-10.0 to 110.0%
Mode
*7
*8
*8
*8
Set up Set up
*8
*9
*9
*9
Expansion Expansion
*11
*11
*12
*12
Option Option
*12
6--9