Table of Contents
Advertisement
Battery Powered Wallstation Reference Sheet
Battery Powered Wallstation
Features
• Bluetooth 4.2 Low Energy transmitter
• Commands Supported:
• Scene selection
• Raise/lower
• Zone level
• No Action
Power:
• Two CR123A replaceable alkaline batteries
Typical Applications
Education, office, and other interior spaces
Models:
• WWBL3: 3 Button
• WWBL3-RL: 3 Button with Raise/Lower
• WWBL5-RL: 5 Button with Raise/Lower
Custom engraving options
Mobile App Details:
• Device Category: Battery Wallstation
• Default Device Name: BPW
Device name will be followed by a number once
provisioned
38
If a custom template is used, behavior will follow the programming used in the template, not the default behavior shown.
39
This command affects all zones in the area.
40
Wallstations with older firmware may not display the second LED color. Update the wallstation firmware to show the described behavior.
20
www.cooperlighting.com
WaveLinx Lite Battery Powered Wallstations simplify new and retrofit installations, allowing manually operated dimming and
scene control without the need for wiring. The WaveLinx Battery Powered Wallstation controls WaveLinx Lite devices by
sending control signals through the Bluetooth Mesh network. WaveLinx Battery Powered Wallstations must be in range of an
always powered on device (integrated, tilemount or fixture mount WaveLinx Lite sensor) to maintain the ability to
communicate while conserving maximum battery life.
Out-of-the-Box Operation
• The wallstation will not control lighting out-of-the-box until it has been provisioned.
• When a button is pressed, the wallstation LED will blink green for 300ms, blue for 500ms, and then OFF for 1.2 seconds,
repeating the cycle for 10 seconds to indicate that the wallstation is powered and in out-of-the-box mode.
Provisioned Device Default Behavior
Once provisioned in a networked area using the WaveLinx Lite Mobile App, the Line Voltage Wallstation operates lighting
assigned to the same area per the default programming. When a button is pressed, the wallstation LED will blink white for
300ms, blue for 500ms, and then OFF for 1.2 seconds, repeating the cycle for 10 seconds.
(WWL5-RL only)
(WWL5-RL only)
LED
location
Loss of Communications Operation
There is no special operation for loss of communications for the wallstation. When the wallstation is powered, it will send a
command anytime a programmed button is pressed. If the controlled devices receive the signal, they will respond.
LED Behavior
The LED is located above the top button on the wallstation.
LED conditions
Flashes green for 300ms, [COLOR2]
40
300 to 500ms and then turns off for 1.2 to
1.4 seconds. Repeats for 10 seconds.
Flashes white for 300ms, [COLOR2]
40
for
300 to 500ms and then turns off for 1.2 to
1.4 seconds. Repeats for 10 seconds.
LED flashes yellow
LED is OFF
Button
Function
1
Scene 3
2
Scene 1
3
Scene 2
4
Scene 4
Press: increase 1% (per press)
Hold: increase 15% (per second)
Press: decrease 1% (per press)
Hold: decrease 15% (per second)
Scene 0
Meaning
for
A button was pressed and the wallstation is not provisioned.
• [COLOR2] Blue = Battery OK (>2.7V)
• [COLOR2] Yellow = Battery Low (2.5V–2.7V)
• [COLOR2] Red =Battery Very Low (<2.5V)
A button was pressed on the provisioned wallstation
• [COLOR2] Blue = Battery OK (>2.7V)
• [COLOR2] Yellow = Battery Low (2.5V–2.7V)
• [COLOR2] Red =Battery Very Low (<2.5V)
The wallstation is being factory reset using the onboard reset.
The LED will be OFF during normal conditions when buttons are not being
pressed if the station is powered
User Manual: WaveLinx Lite (4.0)
Default Level
38
50%
100%
70%
30%
39
39
39
39
OFF
Advertisement
Table of Contents
