Table of Contents
Advertisement
Create Templates for Initial Site Setup
This section is written specifically for site commissioning agents who are performing the initial WaveLinx Lite 4.0 equipment setup. For facility
owners/other personnel that are using the WaveLinx Lite Mobile App to administer a site that has already been programmed, skip to "Modify
Programming in Networked Areas" on page 80 or "Modify Programming in Standalone Areas" on page 119.
Before beginning the site setup, first create any templates that will be needed for the site.
The mobile app automatically provides two default templates which will be used for creating new areas unless a customized template is made.
Default Networked Area Template Settings:
• Zones Created: 1 default dimming zone
Default dim level is 10%
•
Zone minimum level 0%
•
•
Zone maximum level 100%
• Occupancy Sets Created: 1 occupancy set
Default zone assigned to default occupancy set
•
Occupancy mode: Occupancy
•
•
Occupancy hold time: 20 minutes
Energy saver mode: Enabled
•
Energy hold time: 10 minutes
•
•
Occupied level/state: 100%/ON
Energy saver level: 50%
•
Unoccupied level/state: 0%/OFF
•
• Scene Levels for zones in the area:
Scene
OFF
Scene 1
Scene 2
Scene 3
Scene 4
Scene 5
Scene 6
If the default template settings match the settings desired no custom templates are necessary. Skip this section and proceed to "Basic Site
Setup Using the Mobile Application" on page 50.
In a typical facility, many rooms may have common layouts that do not match the default templates provided. Create custom templates for
these locations to streamline setup. By adjusting the settings in a custom template, it reduces the time spent having to apply the settings to
each area.
Create Custom Templates
Create customized templates for networked and standalone areas as needed to match the common layouts needed.
Custom Template Details
• Once an area is created from a custom template, it remains linked to the template until devices are provisioned in the area. This means
that it is possible to edit a template and depending on where the template is edited, have the areas created from that template update
automatically if they do not yet have provisioned devices.
• Once an area is provisioned, the area is no longer linked to the custom template. Each provisioned area will need to be manually updated if
they need to match new template settings due to the need for the mobile device needing to be in the vicinity of provisioned devices.
• Custom templates are stored to a registered user's cloud account so that they can be recalled for future projects. The template is not
stored in the site file.
• Custom templates can be shared with other registered users of the WaveLinx Lite Mobile App. For details on sharing templates, see "Share
Templates with other Registered Users" on page 47.
48
Energy saver state issues after the energy hold time expires. Then, dimmable lighting remains at energy saver level until the occupancy hold time expires, triggering the
unoccupied state. Non dimmable zones will remain at occupied level until the unoccupied state is triggered.
49
If occupancy is sensed in the 30 seconds after an unoccupied command is issued (grace period), the device will resume the previous light level. If outside of the grace
period, the light level issued when occupied will be as defined for the occupied command. Devices with older firmware may not observe the 30 second grace period.
50
Occupancy sensor is automatically set to Occupancy mode. Vacancy mode is not supported in a standalone area.
34
www.cooperlighting.com
48
49
Light Level Response
0%
OFF
100%
ON
70%
ON
50%
ON
30%
ON
10%
ON
1%
ON
Default Standalone Area Template
Device default settings include:
• Device low end trim settings: 0%
• Device high end trim settings: 100%
• Occupied hold time: 20 minutes
• Energy saver mode: Enabled
• Energy hold time: 10 minutes
• Occupied level: 100%/ON
49
• Energy saver level: 50%
•
Unoccupied level: 0%/OFF
User Manual: WaveLinx Lite (4.0)
48, 50
Advertisement
Table of Contents
