Mitsubishi MELSEC-Q series User Manual page 9

3.4.1 Buffer memory assignment................................................................................................... 3 - 27
3.4.2 D/A conversion enable/disable setting (Un\G0).................................................................... 3 - 30
3.4.3 CH digital values (Un\G1 to Un\G6) ..................................................................................... 3 - 30
3.4.4 CH[ ]set value check codes (Un\G11 to Un\G16)................................................................. 3 - 31
3.4.5 Error codes (Un\G19) ........................................................................................................... 3 - 31
3.4.6 Setting range (Un\G20, Un\G21) .......................................................................................... 3 - 32
3.4.7 Offset/gain setting mode and offset/gain specification (Un\G22, Un\G23) ........................... 3 - 32
3.4.8 Offset/gain adjustment value specification (Un\G24) ........................................................... 3 - 33
3.4.9 Offset/gain range setting (Un\G25)....................................................................................... 3 - 33
3.4.10 Rate control enable/disable setting (Un\G46)....................................................................... 3 - 34
3.4.11 Warning output setting (Un\G47).......................................................................................... 3 - 34
3.4.12 Warning output flag (Un\G48)............................................................................................... 3 - 35
3.4.13 Scaling enable/disable setting (Un\G53) .............................................................................. 3 - 35
3.4.14 Scaling upper/lower limit value (Un\G54 to Un\G65)............................................................ 3 - 36
3.4.15 CH increase/decrease digital limit values (Un\G70 to Un\G81)............................................ 3 - 36
3.4.16 CH warning output upper limit value/lower limit value (Un\G86 to Un\G97)......................... 3 - 36
3.4.17 Mode switching setting (Un\G158, Un\G159) ....................................................................... 3 - 37
3.4.18 Save data classification setting (Un\G200)........................................................................... 3 - 37
3.4.19 Factory default setting and user range settings offset/gain values
(Un\G202 to Un\G225) ......................................................................................................... 3 - 38
4 SETUP AND PROCEDURES BEFORE OPERATION
4.1 Handling Precautions...................................................................................................................... 4 - 1
4.2 Setup and Procedures before Operation ......................................................................................... 4 - 3
4.3 Part Names...................................................................................................................................... 4 - 4
4.4 Wiring............................................................................................................................................... 4 - 6
4.4.1 Wiring precautions.................................................................................................................. 4 - 6
4.4.2 External wiring ....................................................................................................................... 4 - 7
4.5 Intelligent Function Module Switch Setting ...................................................................................... 4 - 8
4.6 Offset/Gain Settings....................................................................................................................... 4 - 11
5 UTILITY PACKAGE (GX Configurator-DA)
5.1 Utility Package Functions ................................................................................................................ 5 - 1
5.2 Installing and Uninstalling the Utility Package ................................................................................. 5 - 2
5.2.1 Handling precautions.............................................................................................................. 5 - 2
5.2.2 Operating environment ........................................................................................................... 5 - 4
5.3 Utility Package Operation ................................................................................................................ 5 - 6
5.3.1 Common utility package operations ....................................................................................... 5 - 6
5.3.2 Operation overview................................................................................................................. 5 - 9
5.3.3 Starting the Intelligent function module utility ....................................................................... 5 - 11
5.4 Initial Setting .................................................................................................................................. 5 - 15
5.5 Auto Refresh Setting...................................................................................................................... 5 - 17
5.6 Monitoring/Test .............................................................................................................................. 5 - 20
5.6.1 Monitor/test screen ............................................................................................................... 5 - 20
5.6.2 Offset/gain setting operation................................................................................................. 5 - 23
5.6.3 Confirmation of Conversion Characteristic ........................................................................... 5 - 25
4 - 1 to 4 - 15
5 - 1 to 5 - 34
A
- 7