HEIDENHAIN CNC PILOT 640 User Manual page 690

G313.................................... 287
end of pocket/island G309.... 271
feed per revolution G95....... 269
feed rate reduction G38....... 266
full circle in XY plane G374... 573
full circle in YZ plane G384... 581
full circle on front/rear face
G304.................................... 280
full circle on lateral surface
G314.................................... 287
G172 circular arc in XY plane 570
G173 circular arc in XY plane 570
G20 chuck part bar/tube....... 245
G402 circular pattern on front/
rear face............................... 283
hole in XY plane G370.......... 571
hole in YZ plane G380.......... 580
hole on lateral surface G310. 286
linear patter in XY plane
G471.................................... 575
linear pattern in YZ plane
G481.................................... 583
linear pattern on front/rear face
G401.................................... 282
linear pattern on lateral surface
G411..................................... 289
linear slot in XY plane G371. 572
linear slot in YZ plane G381. 580
linear slot on front/rear face
G301.................................... 279
linear slot on lateral surface
G311..................................... 286
line segment in a contour
G1........................................ 247
line segment in a lateral surface
contour G111........................ 284
line segment in front/rear face
contour G101....................... 277
line segment in XY plane
G171.................................... 569
line segment in YZ plane
G181.................................... 578
polygon in XY plane G377.... 574
polygon in YZ plane G387.... 582
polygon on front/rear face
G307.................................... 281
polygon on lateral surface
G317.................................... 288
recess (general) G23............ 255
recess (standard) G22.......... 253
rectangle in XY plane G375.. 573
rectangle in YZ plane G385.. 582
rectangle on front/rear face
G305.................................... 281
rectangle on lateral surface
G315.................................... 288
single surface in XY plane
G376.................................... 577
690
single surface in YZ plane
G386.................................... 585
starting point of contour in XY
plane G170........................... 569
starting point of contour in YZ
plane G180........................... 578
starting point of front/rear face
contour G100....................... 277
starting point of lateral surface
contour G110........................ 284
start of pocket/island G308.. 271
superimposed elements G39....
267
thread (general) G37............ 262
thread (standard) G34.......... 261
thread with undercut G24.... 257
undercut contour G25.. 258, 497
G code for machining...............
absolute datum shift G59..... 307
activating datum shift, tool
length G981......................... 447
activating datum shift G980. 447
actual values in variable
G901.................................... 440
additive correction G149...... 313
additive datum shift G56...... 306
area milling – finishing in Y axis
G842.................................... 594
area milling on front face
G797.................................... 413
area milling – roughing in Y axis
G841.................................... 593
axis-parallel oversize G57..... 308
bore milling G75.................. 381
centric polygon – finishing in Y
axis, G844............................ 596
centric polygon – roughing in Y
axis G843............................. 595
chucking equipment G65....... 62
circular arc ccw G12............ 295
circular arc ccw G13............ 295
circular arc ccw G2.............. 294
circular arc ccw G3.............. 294
circular arc cw in Y axis,
G12...................................... 592
circular arc cw in Y axis,
G13...................................... 592
circular arc cw in Y axis, G2. 591
circular arc cw in Y axis, G3. 591
circular arc on front/rear face
G102.................................... 397
circular arc on front/rear face
G103.................................... 397
circular arc on lateral surface
G112..................................... 402
circular arc on lateral surface
G113..................................... 402
circular pattern on front face
HEIDENHAIN | User's Manual smart.Turn and DIN Programming | 12/2017
G745..................................... 385
circular pattern on lateral surface
G746..................................... 389
circular slot on front face
G302.................................... 340
circular slot on front face
G303.................................... 340
circular slot on lateral surface
G312.................................... 343
circular slot on lateral surface
G313.................................... 343
clamping G65....................... 439
compensation of left-hand tool
tip G151............................... 314
compensation of right-hand tool
tip G150............................... 314
constant cutting speed G96. 300
678 constant feed G94............... 298
contour and figure milling cycle
on front face G793............... 408
contour and figure milling cycle
on lateral surface G794........ 410
contour cycle bidirectional G835
(contour-parallel with neutral
tool)...................................... 325
contour finishing G890......... 335
contour follow-up G703........ 438
contour milling G840............ 416
contour-parallel oversize G58....
309
contour-parallel roughing G830...
323
controlled parting G917........ 496
converting and mirroring
G30...................................... 489
correction of cut G148 (changing
the cutter compensation)..... 312
cut-off cycle G859................ 360
cycle end / simple contour
G80...................................... 339
datum shift G51................... 305
datum shift in variable G902. 440
datum shifts G53/G54/G55... 306
deactivating datum shift
G920.................................... 442
deactivating datum shifts, tool
length G921......................... 442
deep boring G74.................. 378
defining monitoring zone
G995.................................... 448
definition of tool change point
G140.................................... 292
direct program-run continuation
G999.................................... 450
eccentric polygon on lateral
surface G317........................ 344
eccentric transition G726..... 453
eccentric turning G725......... 452
Index