HEIDENHAIN CNC PILOT 640 User Manual page 688

Index
#
# variables, output.................... 458
A
Actual values in variable G901.. 440
Additive correction G149.......... 313
Additive correction G149-Geo... 270
Address parameters................. 238
Angular measurement G787.... 560
API thread G352...................... 357
Approach, smart.Turn................. 84
attributes for contour description....
266
Automatic job............................. 74
Automatic working plan
generation................................ 619
AWG......................................... 619
full-surface machining.......... 653
list of machining................... 625
machining sequence............ 621
machining sequence, editing....
623
B
B axis
compensation during program
run........................................ 658
flexible use of tools.............. 657
fundamentals....................... 656
simulation............................ 659
Blank contour G67 (for
graphics)................................... 439
Bore hole
centric G49–Geo.................. 265
front face G300-Geo............ 279
Boring G72............................... 375
C
Calculating hole positions
G840........................................ 417
Calculating hole positions
G845........................................ 426
Calculating hole positions G845 (Y
axis).......................................... 598
Calculation of pitch circle G786 558
Calibrating
touch probe, standard G747. 539
touch probe via two points
G748..................................... 541
Calibrating touch probes........... 539
Cast part G21-Geo.................... 245
C axis
G code................................. 392
offset C angle G905............. 494
C axis contour
688
fundamentals....................... 271
Centric polygon
finishing G844...................... 596
roughing G843..................... 595
XY plane G477-Geo.............. 577
YZ plane G487-Geo.............. 585
chamfer G88............................ 504
Character set............................ 433
Chucking equipment in simulation
G65............................................ 62
Chuck part bar/tube G20-Geo... 245
Circular arc
front face contour G102-/G103-
Geo...................................... 278
front face G102/G103........... 397
lateral surface contour G112-/
G113-Geo............................. 285
lateral surface G112/G113..... 402
turning contour G12-/G13-
Geo...................................... 251
turning contour G2-/G3-Geo. 249
XY plane G172-/G173-Geo.... 570
YZ plane G182/G183-Geo..... 579
Circular arc ccw
G12/G13............................... 295
G2/G3................................... 294
Circular arc cw
milling G12, G13.................. 592
milling G2, G3...................... 591
Circular measurement G785.... 556
Circular movement................... 293
Circular pattern with circular
slots......................................... 274
Circular slot
front face G302-/G303-Geo.. 280
lateral surface G312-/G313-
Geo...................................... 287
XY plane G372/G373-Geo.... 572
YZ plane G382/G383-Geo.... 581
Clamping in the simulation
G65.......................................... 439
Code
CONST................................... 68
END....................................... 68
return..................................... 68
VAR........................................ 69
Compensation.......................... 311
B axis................................... 658
Compensation of right-hand/left-
hand tool tip G150/G151.......... 314
Conditional block run................ 477
Configuration data, reading...... 472
Connection between geometry and
machining commands.............. 509
C axis – front face................ 510
C axis – lateral surface......... 510
HEIDENHAIN | User's Manual smart.Turn and DIN Programming | 12/2017
turning.................................. 509
Constant cutting speed Gx96... 300
Contour
in XY plane........................... 569
in YZ plane........................... 578
simple G80.......................... 339
Contour and figure milling cycle on
lateral surface G794................. 410
Contour-based turning cycle..... 315
Contour finishing G890............ 335
Contour follow-up............... 42, 438
on/off G703.......................... 438
saving/loading G702............. 438
Contour form.............................. 80
Contour milling G840............... 416
Contour programming.............. 234
Contour repeat cycle G83........ 501
Contour thread......................... 359
Control graphic TURN PLUS..... 635
Controlled parting using lag error
monitoring G917...................... 496
Converting and mirroring G30.. 489
Converting lengths G927.......... 443
Coolant
TURN PLUS machining
information........................... 638
Correction
additive G149....................... 313
additive G149-Geo............... 270
Correction of cut (changing
the cutter compensation)
G148................................ 312, 312
Countersinking G72.................. 375
Creating a job............................. 74
Cut-off cycle G859................... 360
Cutter radius compensation..... 302
Cutting limit.............................. 568
Cutting speed, constant Gx96.. 300
Cycle, undercut G85................. 361
Cycle end / simple contour
G80.......................................... 339
D
Data input................................ 457
Data output.............................. 457
Date......................................... 462
Datum, C-axis object center
G773........................................ 529
Datum, single point w/ C axis
G772........................................ 527
Datum shift
absolute G59....................... 307
activating G980.................... 447
activating tool length G981.. 447
additive G56......................... 306
C axis G152......................... 392
deactivating G920................ 442
deactivating tool length
Index