TDK-Lambda Genesys Series Manuals

Manuals and User Guides for TDK-Lambda Genesys Series. We have 17 TDK-Lambda Genesys Series manuals available for free PDF download: User Manual, Product Safety & Installation Manual, Technical Manual, Manual, Instruction Manual

TDK-Lambda Genesys Series User Manual

TDK-Lambda Genesys Series User Manual (209 pages)

Built-in LAN ( 1.5), USB, RS-232 & RS-485 Interfaces Built-in Remote Isolated Analog Program/Monitor/Control Interface Optional Interface: IS420, IEEE488.2 SCPI (GPIB), Modbus TCP or EtherCAT

Brand: TDK-Lambda | Category: Power Supply | Size: 83.88 MB

Table of Contents

Table of Contents
8
Chapter 1: Front/Rear Panel Control & Connectors

16
Chapter 2: Local Operation

40
- Connecting Single Loads, Local Sensing (Default)
  40
- Introduction
  40
- Load Connections Options
  40
- Connecting Single Loads, Remote Sensing
  41
- Connecting Multiple Loads, Radial Distribution Method
  42
- Multiple Load Connection with Distribution Terminals
  42
- Constant Voltage Mode and Voltage Setting
  43
- Automatic Crossover
  44
- Constant Current Mode and Current Setting
  44
- Output On/Off Control
  44
- Alarms and Protective Functions
  45
- Introduction
  45
- Safe-Start and Auto-Restart Modes
  45
- Viewing Software Revision
  45
- Over Voltage Protection
  46
- Activated OVP Alarm
  47
- Resetting the OVP Circuit
  47
- Under Voltage Protection and under Voltage Limit
  47
- Activated UVP Alarm
  48
- Resetting UVP Alarm
  48
- Activated FOLD Alarm
  49
- Foldback Protection
  49
- AC Fail Alarm
  50
- Over Temperature Protection
  50
- Protection Delay
  50
- Resetting FOLD Alarm
  50
- Series Operation (Applicable to 10V-600V Only)
  51
- Series Connection for Increased Output Voltage
  52
- Series Connection for Positive and Negative Output Voltage
  52
- Remote Programming in Series Operation
  53
- Daisy in Function
  54
- Daisy-Chain Connection
  54
- Interlock Function - Analog On/Off (Enable/Disable)
  55
- Rear Panel (J1 Connector) Functions
  55
- Activated ENA Alarm
  56
- Activated ILC Alarm
  56
- Enable in Function
  56
- Enable in Polarity
  56
- Auxiliary Programmed Signals Prog_Out_1 and Prog_Out_2
  57
- Power Supply OK Signal
  57
- CV/CC Signal
  58
- Default Setting
  58
- Parameter Setting Memory
  58
- Last Setting Memory
  59
- Recall <1
  59
- Reset
  59
- Save <1
  59
Chapter 3: Remote Analog Programming

63
Chapter 4: Serial Rs232/Rs485, Usb, & Lan Interfaces

67
- Communication Interface Selection
  67
- Configuration
  67
- Default Setting
  67
- Introduction
  67
- Address Setting
  68
- IP Address Setting
  68
- Baud Rate Setting
  69
- Language Selection (RS232/RS485, USB)
  69
- Setting Unit in Remote, Local Lockout, or Local Mode
  70
- Rear Panel RS232/RS485 in Connector
  71
- Rear Panel RS485 out Connector
  72
- Connecting Power Supply to RS232 or RS485 BUS
  73
- Rear Panel USB Connector
  74
- USB Getting Started
  74
- Feature Summary
  75
- Introduction
  75
- Rear Panel LAN
  75
- LAN Specifications
  76
- Specifications
  76
- LAN Command Speed
  78
- Control Method Options
  79
- LAN Status Leds
  79
- Select LAN Remote Mode
  79
- Select the Control Method
  79
- Connect to a Network
  80
- LAN Cable
  80
- Types of Networks
  80
- Power-Up the LAN Power Supply
  81
- Hostname
  82
- IP Addresses
  82
- Description and DNS Service Names
  83
- LAN Setup
  84
- View the IP and MAC Addresses
  84
- Change the IP Address
  85
- LAN Reset
  85
- Benefits of Web
  86
- Opening the HOME Page
  86
- Web
  86
- The Home Page
  87
- DC Power Page
  89
- Login Rules
  89
- LAN Page
  92
- HELP Page
  97
- Opening a VISA Connection
  97
- Programming Using VISA Drivers
  97
- VISA Description
  97
- VXI-11 Compatibility
  97
- Communicating Using Sockets
  98
- Communicating Using VISA
  98
- Controller Access: Single and Multiple Clients
  98
- Programming Using Sockets
  98
- Socket Description
  98
- Input Buffer Requirements
  99
- Message Terminators
  99
- Connecting over WAN
  100
- Use Sockets over WAN
  100
- Using TCP Sockets
  100
- Using UDP Sockets
  100
- View Web Pages over WAN
  100
- Multi Power Supply Connection (Daisy-Chain) to RS232, RS485, USB, or LAN
  101
- Multi Power Supply Connection (Daisy-Chain) - Multiple DC Programmable Power Supply Series
  103
- Acknowledge
  104
- Backspace
  104
- Checksum
  104
- Command Repeat
  104
- Data Format
  104
- End of Message
  104
- GEN Protocol (GEN Series Communication Language)
  104
- Command Set Categories
  105
- GEN Command Set Description
  105
- General Guides
  105
- Numeric / Data Type Parameters
  105
- Identification Commands
  106
- Initialization Commands
  106
- Output Commands
  107
- Global Output Commands
  110
- Auxiliary Commands
  113
- Status Commands
  115
- Serial Communication Test Set-Up
  117
- Checksum
  118
- Data Format
  118
- End of Command
  118
- SCPI Protocol
  118
- SCPI Requirements
  118
- Data Formats
  119
- Header
  119
- SCPI Command Hierarchy
  119
- Commands Notes
  120
- SCPI Common Commands
  120
- Display Subsystem
  125
- SCPI Subsystem Commands
  125
- Initiate Subsystem
  126
- Instrument Subsystem
  126
- Global Subsystem
  127
- Measure Subsystem
  128
- Output Subsystem
  128
- Program Subsystem
  131
- Source Subsystem
  134
- Status Subsystem
  140
- System Subsystem
  143
- Trigger Subsystem
  150
- SCPI Commands Summary
  151

Advertisement

TDK-Lambda Genesys Series User Manual

TDK-Lambda Genesys Series User Manual (190 pages)

Brand: TDK-Lambda | Category: Power Supply | Size: 7.88 MB

Table of Contents

Table of Contents
6
Chapter 1: Front/Rear Panel Control & Connectors

12
Chapter 2: Local Operation

34
- Connecting Single Loads, Local Sensing (Default)
  34
- Introduction
  34
- Load Connections Options
  34
- Connecting Single Loads, Remote Sensing
  35
- Connecting Multiple Loads, Radial Distribution Method
  36
- Multiple Load Connection with Distribution Terminals
  36
- Constant Voltage Mode and Voltage Setting
  37
- Automatic Crossover
  38
- Constant Current Mode and Current Setting
  38
- Output On/Off Control
  38
- Alarms and Protective Functions
  39
- Introduction
  39
- Safe-Start and Auto-Restart Modes
  39
- Viewing Software Revision
  39
- Over Voltage Protection
  40
- Resetting the OVP Circuit
  40
- Activated OVP Alarm
  41
- Under Voltage Protection and under Voltage Limit
  41
- Activated UVP Alarm
  42
- Foldback Protection
  42
- Activated FOLD Alarm
  43
- Over Temperature Protection
  43
- Protection Delay
  43
- AC Fail Alarm
  44
- Series Operation
  44
- Series Connection for Increased Output Voltage
  45
- Series Connection for Positive and Negative Output Voltage
  45
- Remote Programming in Series Operation
  46
- Daisy in Function
  47
- Daisy-Chain Connection
  47
- Interlock Function - Analog On/Off (Enable/Disable)
  48
- Rear Panel (J1 Connector) Functions
  48
- Activated ENA Alarm
  49
- Activated ILC Alarm
  49
- Enable in Function
  49
- Enable_In Polarity
  49
- Auxiliary Programmed Signals Prog_Out_1 and Prog_Out_2
  50
- Power Supply OK Signal
  50
- CV/CC Signal
  51
- Default Setting
  51
- Parameter Setting Memory
  51
- Last Setting Memory
  52
- Recall <1
  52
- Reset
  52
- Save <1
  52
Chapter 3: Remote Analog Programming

55
- Introduction
  55
- Local/Remote Analog Control
  55
- Local/Remote Analog Indication
  55
- Remote Voltage Programming of Output Voltage and Current
  56
- Remote Resistor Programming of Output Voltage and Output Current
  57
- Monitoring of Output Voltage (V_MON) and Current (I_MON)
  58
- Communication Interface Selection
  59
- Configuration
  59
- Default Setting
  59
- Introduction
  59
- Serial Rs232/Rs485, Usb & Lan Interfaces
  59
- Address Setting
  60
- IP Address Setting
  60
- Baud Rate Setting
  61
- Language Selection (RS232/RS485, USB)
  61
- Setting Unit in Remote, Local Lockout or Local Mode
  62
- Rear Panel RS232/RS485 in Connector
  63
- Rear Panel RS485 out Connector
  64
- Connecting Power Supply to RS232 or RS485 BUS
  65
- Rear Panel USB Connector
  66
- USB Getting Started
  66
- Feature Summary
  67
- Introduction
  67
- Rear Panel LAN
  67
- LAN Specifications
  68
- Specifications
  68
- LAN Command Speed
  70
- Control Method Options
  71
- LAN Status Leds
  71
- Select LAN Remote Mode
  71
- Select the Control Method
  71
- Connect to a Network
  72
- LAN Cable
  72
- Types of Networks
  72
- Power-Up the LAN Power Supply
  73
- Hostname
  74
- IP Addresses
  74
- Description and DNS Service Names
  75
- Change the IP Address
  76
- LAN Setup
  76
- View the IP and MAC Addresses
  76
- LAN Reset
  77
- Benefits of Web
  78
- Opening the HOME Page
  78
- Web
  78
- The Home Page
  79
- Login Rules
  80
- DC Power Page
  81
- LAN Page
  84
- Compatibility
  88
- HELP Page
  88
- Programming Using VISA Drivers
  88
- VISA Description
  88
- Communicating Using Sockets
  89
- Communicating Using VISA
  89
- Controller Access: Single and Multiple Clients
  89
- Opening a VISA Connection
  89
- Programming Using Sockets
  89
- Socket Description
  89
- Input Buffer Requirements
  90
- Message Terminators
  90
- Connecting over WAN
  91
- Use Sockets over WAN
  91
- Using TCP Sockets
  91
- Using UDP Sockets
  91
- View Web Pages over WAN
  91
- Multi Power Supply Connection (Daisy-Chain) to RS232, RS485, USB or LAN
  92
- Checksum
  94
- Command Repeat
  94
- Data Format
  94
- End of Message
  94
- GEN Protocol (GEN Series Communication Language)
  94
- Acknowledge
  95
- Backspace
  95
- Command Set Categories
  95
- GEN Command Set Description
  95
- General Guides
  95
- Numeric / Data Type Parameters
  95
- Identification Commands
  96
- Initialization Commands
  96
- Output Commands
  97
- Global Output Commands
  100
- Auxiliary Commands
  103
- Status Commands
  104
- Serial Communication Test Set-Up
  106
- Checksum
  107
- Data Format
  107
- End of Command
  107
- SCPI Protocol
  107
- SCPI Requirements
  107
- Data Formats
  108
- Header
  108
- SCPI Command Hierarchy
  108
- Commands Notes
  109
- SCPI Common Commands
  109
- Display Subsystem
  114
- SCPI Subsystem Commands
  114
- Initiate Subsystem
  115
- Instrument Subsystem
  115
- Global Subsystem
  116
- Measure Subsystem
  116
- Output Subsystem
  117
- Program Subsystem
  119
- Source Subsystem
  123
- Status Subsystem
  128
- System Subsystem
  131
- Trigger Subsystem
  137
- SCPI Commands Summary
  138

TDK-Lambda Genesys Series User Manual

TDK-Lambda Genesys Series User Manual (113 pages)

10KW/15KW programmable dc power supplies

Brand: TDK-Lambda | Category: Power Supply | Size: 4.18 MB

Table of Contents

Table of Contents
7
Warranty

10
Safety Instructions

11
1 General Information

29
- User Manual Content
  29
- Introduction
  29
- Accessories
  31
- Model Number Format
  32
2 Specifications

33
- Output Rating (Duty Cycle Continuous Duty)
  33
- Input Characteristics
  33
- Static Characteristics
  33
- Protective Functions
  34
- Dynamic Characteristics
  34
- Remote Analog Control and Signals
  35
- Front Panel
  36
- Software Spec
  36
- Digitial Programming and Readback
  37
- Mechanical Construction
  37
- Environmental Conditions
  37
- Emc
  38
- Safety
  38
- J1 Connector
  39
3 Installation

40
- General
  40
- Preparation for Use
  40
- Initial Inspections
  40
- Rack Mounting
  41
- Location, Mounting and Cooling
  41
- AC Source Requirements
  41
- AC Input Power Connection
  41
- Turn-On Checkout Procedure
  43
- Connecting the Load
  45
- Local and Remote Sensing
  49
- Repackaging for Shipment
  51
4 Front and Rear Panel Controls and Connectors

52
5 Local Operation

60
- Introduction
  60
- Standard Operation
  60
- Over Voltage Protection (OVP)
  61
- Under Voltage Limit (UVL)
  62
- Foldback Protection
  62
- Output ON/OFF Control
  63
- Output SHUT-OFF (SO) Control Via Rear Panel J1 Connector
  63
- Enable/Disable Control Via Rear Panel J1 Connector
  64
- CV/CC Signal
  64
- PS_OK Signal
  64
- Safe Start and Auto-Restart Modes
  65
- Front Panel Locking
  65
- Over Temperature Protection (OTP)
  66
- Last Setting Memory
  66
6 Series and Parallel Operation

67
- Series Operation
  67
- Parallel Operation (Single-Wire/Two-Wire Method)
  70
7 Remote and Analog Programming

78

Advertisement

TDK-Lambda Genesys Series User Manual

TDK-Lambda Genesys Series User Manual (70 pages)

LAN Interface

Brand: TDK-Lambda | Category: Power Supply | Size: 2.17 MB

Table of Contents

Table of Contents
2
1 General Information

5
2 Specifications

7
3 Select the Control Method

10
4 Connect to Network

13
- LAN Cable
  13
- Types of Networks
  13
- Figure 4. Server Network Connection Diagram
  13
- Power-Up the LAN Power Supply
  14
- Figure 5. Peer-To-Peer Connection Diagram
  14
- IP Addresses
  15
- Hostnames
  15
- Description and DNS Service Names
  16
5 Lan Setup

17
- View the IP and MAC Addresses
  17
- Change the IP Address
  17
- LAN Reset
  18
- Default LAN Settings
  19
6 Web

20
- Benefit of Web
  20
- Opening the HOME Page
  20
- The HOME Page
  21
- Figure 6. Web HOME Page
  21
- Logging in
  22
- DC Power Page
  23
- LAN Page
  27
- HELP Page
  31
7 Programming Using Visa Drivers

32
- VISA Description
  32
- VXI-11 Compatibility
  32
- Opening the VISA Connection
  32
- Communicating Using VISA
  32
8 Programming Using IVI Drivers

33
- IVI Description
  33
- IVI Support
  33
9 Programming Using Sockets

34
- Socket Description
  34
- Communicating Using Sockets
  34
- Controller Access: Single and Multiple Clients
  34
- Input Buffer Requirements
  35
- Message Terminators
  36
- Using TCP Sockets
  36
- Using UDP Sockets
  36
10 Connecting over Wan

37
- View Web Pages over WAN
  37
- Use Sockets over WAN
  37

TDK-Lambda Genesys Series Product Safety & Installation Manual

TDK-Lambda Genesys Series Product Safety & Installation Manual (70 pages)

Brand: TDK-Lambda | Category: Power Supply | Size: 27.7 MB

Table of Contents

Table of Contents
3
Environmental Compliance
5
General Information
5
Warranty
5
Long-Term Storage Method and Long-Term Storage Period
6
Safety & Emc Approvals
8
General Safety Instructions
9
Allgemeine Sicherheitsvorschriften
11
Instrucciones de Seguridad Generales
13
Consignes Générales de Sécurité
15
Istruzioni Generali DI Sicurezza
17
Instruções Gerais de Segurança
19
Product Safety Instructions
21
Chapter 1: General Information

27
- User Manual Content
  27
- Introduction
  27
- General Description
  27
- Multiple Output Power System
  27
- Control Via Communication Ports
  27
- Analog Voltage Programming and Monitoring
  28
- Parallel Operation
  28
- Output Connections
  28
- Cooling and Mechanical Construction
  28
- Accessories
  28
- Accessories Provided with the Power Supply
  28
- Input Connector Protection for 1.5Kw Models
  28
- AC Input Plug for 1.5Kw Models
  28
- Output Protection Cover for Models up to 100VDC Output
  28
- Output Connector for Models above 100VDC Output
  29
- Serial Link Cable
  29
- Misc. Hardware
  29
- Optional Accessories
  29
- Printed User Manual
  29
- Serial Port Cables
  29
- Paralleling Cable
  29
- Rack Mount Kit
  29
- AC Cables
  30
Chapter 2: Front/Rear Panel Controls and Connectors

31
- Introduction
  31
- Front Panel Display and Controls
  31
- Blank Front Panel
  34
- Rear Panel Connectors
  35
Chapter 3: Outline

37
- Power Supplies Outline
  37
Chapter 4: Installation

39
- General
  39
- Preparation for Use
  40
- Initial Inspection
  40
- Rack Mounting Option
  41
- GH/RM Option Kit
  41
- Single Unit Installation
  41
- Dual Unit Installation
  43
- GH\RM Rack Mounting Outline Drawings
  45
- Benchtop Stacking Option
  46
- GH/MO Option Kit
  46
- GH/MO Installation
  46
- Location, Mounting and Cooling
  47
- Foot Snaps Assembly
  47
- AC Input Power Connection
  48
- AC Input Connector
  50
- AC Input Wire Connection
  51
- Turn-On Checkout Procedure
  53
- General
  53
- Prior to Operation
  53
- Constant Voltage Check (Standard Power Supply)
  53
- Constant Voltage Check (Blank Panel Power Supply)
  54
- Constant Current Check (Standard Power Supply)
  54
- Constant Current Check (Blank Panel Power Supply)
  55
- Connecting the Load
  56
- Load Wiring
  56
- Current Carrying Capacity
  56
- Bus Bar Cover Limitation
  57
- Wire Termination
  57
- Noise and Impedance Effects
  57
- Inductive Loads
  58
- Making the Load Connections
  58
- Grounding Outputs
  62
- Local and Remote Sensing
  63
- Sense Wiring
  63
- Local Sensing
  63
- Remote Sensing
  63
- J8 Sense Connector Technical Information
  64
- Repackaging for Shipment
  64

TDK-Lambda Genesys Series User Manual

TDK-Lambda Genesys Series User Manual (65 pages)

Optional Interface: LXI Compliant LAN

Brand: TDK-Lambda | Category: Power Supply | Size: 2.81 MB

Table of Contents

Table of Contents
4
1 General Information

6
2 Specifications

8
- Power Supply Specifications
  8
- LAN Specifications
  8
- LAN Command Speed
  10
3 Select the Control Method

11
4 Connect to Network

14
- LAN Cable
  14
- Types of Networks
  14
- Figure 4. Server Network Connection Diagram
  14
- Figure 5. Peer-To-Peer Connection Diagram
  14
- Power-Up the LAN Power Supply
  15
- IP Addresses
  15
- Hostnames
  16
5 Lan Setup

17
- View the IP and MAC Addresses
  17
- Change the IP Address
  18
- LAN Reset
  19
6 Web

20
- Benefit of Web
  20
- Opening the HOME Page
  20
- The HOME Page
  21
- Figure 6. Web HOME Page
  21
- Logging in
  22
- DC Power Page
  23
- LAN Page
  26
- HELP Page
  30
7 Programming Using Visa Drivers

31
- VISA Description
  31
- VXI-11 Compatibility
  31
- Opening the VISA Connection
  31
- Communicating Using VISA
  31
8 Programming Using IVI Drivers

32
- IVI Description
  32
- IVI Support
  32
9 Programming Using Sockets

33
- Socket Description
  33
- Communicating Using Sockets
  33
- Special Requirements for Socket Programs
  33
- Controller Access: Single and Multiple Clients
  33
- Input Buffer Requirements
  34
- Message Terminators
  34
- Using TCP Sockets
  35
- Using UDP Sockets
  35
- Other Ports
  35
10 Connecting over Wan

36
- View Web Pages over WAN
  36
- Use Sockets over WAN
  36

TDK-Lambda Genesys Series User Manual

TDK-Lambda Genesys Series User Manual (42 pages)

IEEE488.2 SCPI (GPIB) Multi-Drop Interface Option

Brand: TDK-Lambda | Category: Power Supply | Size: 1.91 MB

Table of Contents

TDK-Lambda Genesys Series Technical Manual

TDK-Lambda Genesys Series Technical Manual (64 pages)

LAN INTERFACE

Brand: TDK-Lambda | Category: Power Supply | Size: 1.94 MB

Table of Contents

Table of Contents
3
1 General Information

5
- Introduction
  5
- Figure 1. Front Panel LAN Features
  5
- Figure 2. Rear Panel LAN Features
  5
- Feature Summary
  6
- Glossary
  7
- Required Accessories
  8
2 Specifications

9
3 Getting Started

13
- Select the Interface
  13
- Setup the Lan Computer
  14
- Figure 4. Network Connection Diagram
  14
- Figure 5. Peer-To-Peer Connection Diagram
  14
- Setup the Lan Power Supply
  15
- Connecting with the Web Page
  15
- Ip Address Overview
  16
- Hostname Overview
  16
- Troubleshooting the Web Connection
  17
- Other Troubleshooting
  18
- Connecting over Wan
  20
- Connecting with Visa Programming
  20
4 Lan Setup

21
- View the Ip and Mac Addresses
  21
- Lan Reset Button
  21
5 Using the Web

23
- Overview
  23
- Home Page
  23
- Logging in
  24
- DC Power Page
  25
- Lan Page
  27
- Help Page
  32
6 Remote Programming Using Commands

33
- Overview
  33
- VXI-11 Compatibility
  33
- Visa Compatiblity
  33
- Scpi Compatibility
  33
- Socket Programming
  34
7 Scpi Command Reference

35
- Command Syntax
  35
- Configuring the Output
  36
- Measuring the Output
  37
- Operating Modes
  37
- Output Protection
  39
- Lan Specific Commands
  40
- Common Commands
  42
- Error and Status Commands
  43
- Figure 6. Error and Status Registers
  46
- Rs-485 Multi-Drop Commands
  51

TDK-Lambda Genesys Series Manual

TDK-Lambda Genesys Series Manual (44 pages)

Programmable DC Power Supplies, MODBUS TCP

Brand: TDK-Lambda | Category: Power Supply | Size: 1.62 MB

Table of Contents

Table of Contents
3
General Information

5
- Introduction
  5
Chapter 1: Introduction

5
- Feature Summary
  5
Chapter 2: Specifications

7
Chapter 3: Select Control Method

11
- MODBUS TCP, LAN, LOCAL, Serial or Analog Control
  11
- MODBUS TCP Interface Option Rear Panel View
  13
Chapter 4: Connect to Network

14
- Ethernet Cable
  14
- Types of Networks
  14
  - Network with a Dhcp Server
    14
  - Peer-To-Peer Network
    14
- IP Addresses
  15
- Power-Up the MODBUS TCP Power Supply
  15
- Hostname
  16
- Change the IP Address
  17
Chapter 5: Modbus Tcp Setup

17
- View the IP and MAC Addresses
  17
- MODBUS TCP Reset
  18
- Benefits of Web Pages
  19
Chapter 6: Web Pages

19
- Opening the Overview Page
  19
- MODULE Overview Page
  20
- MODULE Parameters Page
  20
- NETWORK Status Page
  20
- NETWORK Configuration Page
  22
- SERVICES SMTP Page
  23
Chapter 7: Programming Using Sockets

24
- Communicating Using Sockets
  24
- Controller Access
  24
- Input Buffer Requirements
  24
- Socket Description
  24
Chapter 8: Connecting over Wan

25
- Use Sockets over WAN
  25
- View Web Pages over WAN
  25
Chapter 9: Modbus Tcp Data Structure

26
- Programming / Monitoring Values Translation
  26
- Data Type
  27
- Data Access
  29
- Data Length (Number of Registers)
  29
- Parameters Range
  29
- Read / Write Registers
  29
- Registers Mapping
  30
- MODBUS TCP Unique Commands Structure
  33
- Sequencer Activation
  38

TDK-Lambda Genesys Series Manual

TDK-Lambda Genesys Series Manual (36 pages)

Programmable DC Power Supplies

Brand: TDK-Lambda | Category: Power Supply | Size: 2.77 MB

Table of Contents

Table of Contents
3
Chapter 1: Introduction

5
- Feature Summary
  5
- General Information
  5
- Introduction
  5
Chapter 2: Specifications

7
Chapter 3: Select Control Method

10
Chapter 4: Programming Using Twincat 3

14
- Establish Twincat Communication
  14
Chapter 5: Ethercat Data Structure

17
- Programming / Monitoring Values Translation
  17
- Data Type
  18
- Data Access
  20
- Data Length (Number of Sdos/Pdos)
  20
- Parameters Range
  20
- Read / Write Sdos / Pdos
  20
- Pdos Mapping
  21
- Sdos Mapping
  22
- Ethercat Unique Commands Structure
  25
- Sequencer Activation
  30
Chapter 6: Multi Power Supply Connection

32
- Connection and Setup
  32
- Introduction
  32
- Parallel Connection
  33

TDK-Lambda Genesys Series User Manual

TDK-Lambda Genesys Series User Manual (32 pages)

Programmable DC Power Supplies

Brand: TDK-Lambda | Category: Power Supply | Size: 2.54 MB

Table of Contents

Table of Contents
3
Chapter 1: General Information

5
- Introduction
  5
- Feature Summary
  5
Chapter 2: Specifications

6
Chapter 3: Select Control Method

9
Chapter 4: Programming Using Twincat 3

13
- Establish Twincat Communication
  13
Chapter 5: Ethercat Data Structure

16
- Programming / Monitoring Values Translation
  16
- Data Type
  17
- Data Access
  19
- Data Length (Number of Sdos/Pdos)
  19
- Parameters Range
  19
- Read / Write Sdos / Pdos
  19
- Pdos Mapping
  20
- Sdos Mapping
  21
- Ethercat Unique Commands Structure
  24
- Sequencer Activation
  29

TDK-Lambda Genesys Series User Manual

TDK-Lambda Genesys Series User Manual (16 pages)

USB Interface

Brand: TDK-Lambda | Category: Power Supply | Size: 0.33 MB

Table of Contents

Table of Contents
3
Warranty

4
Safety

4
1 General Information

5
2 Specifications

6
3 Required Equipment

8
4 Grounding and Safety

8
5 Install USB Drivers for a Virtual COM Port

9
- Installation CD-ROM
  9
- Install Drivers
  9
6 Install USB Library Drivers

9
7 Communicating Using a Virtual COM Port

10
- Setup the Power Supply
  10
- Find the Assigned COM Port
  11
- Open a Terminal Communication Program
  11
- Open the Assigned COM Port
  12
- Setup the COM Port
  12
- Get the Power Supply Address
  13
- Start Typing Commands
  14
8 Linking Multiple Supplies

15
- Communication Daisy-Chain
  15
- Series and Parallel Supplies
  15

TDK-Lambda Genesys Series Instruction Manual

TDK-Lambda Genesys Series Instruction Manual (28 pages)

Programmable DC Power Supplies, G1.7 - 5kW in 1U 0-600V, 0-500A, PARALLEL KIT

Brand: TDK-Lambda | Category: Power Supply | Size: 2.43 MB

TDK-Lambda Genesys Series Instruction Manual

TDK-Lambda Genesys Series Instruction Manual (20 pages)

Parallel Kit for Programmable DC Power Supplies.

Brand: TDK-Lambda | Category: Cables and connectors | Size: 1.51 MB

Table of Contents

TDK-Lambda Genesys Series Manual

TDK-Lambda Genesys Series Manual (10 pages)

Air Filter Kit for Programmable DC Power Supplies. Standard and Blank Panel Options.

Brand: TDK-Lambda | Category: Power Supply | Size: 0.78 MB

TDK-Lambda Genesys Series Instruction Manual

TDK-Lambda Genesys Series Instruction Manual (8 pages)

Parallel Kit for Programmable DC Power Supplies

Brand: TDK-Lambda | Category: Cables and connectors | Size: 1.22 MB

TDK-Lambda Genesys Series Instruction Manual

TDK-Lambda Genesys Series Instruction Manual (4 pages)

Parallel Kit for Programmable DC Power Supplies

Brand: TDK-Lambda | Category: Cables and connectors | Size: 0.45 MB

Advertisement

Related Products

TDK-Lambda Categories

Power Supply

Power Supply Media Converter Cables and connectors Portable Generator Network Hardware

More TDK-Lambda Manuals