Lexmark X925 Service Manual page 478

7541-03x
4-63
Duplex removal
Duplex solenoid removal
Engine board (MDCONT)
Exit guide (paper exit) roll removal
Fuser entry sensor removal
Fuser exit drive unit motor
4-92
Fuser Fan
4-62
handle cover removal
4-111
HVPS removal
LED assembly removal
LED print head removal
4-22
left cover removal
4-53
main fan removal
4-94
Modem
4-174
MPF clutch removal
4-187
MPF pad removal
MPF tray assembly removal
Option controller board removal
Option door inter lock switch removal
Paper empty sensor removal
paper exit guide removal
paper exit sensor removal
Paper feed clutch removal
Paper feed motor removal
Paper feed roll removal
paper feed unit removal
Paper full sensor removal
Paper level sensor removal
paper size sensor removal
Paper size switch removal
Paper size switches removal
Paperfeed roll removal
Paperfeed unit clutch removal
Papertray lift motor removal
photoconductor lock removal
4-182
Pick roll removal
power supply fan removal
printhead controller board removal
Rear EMI shield – Not a FRU
4-102
Rear fan
Registration roll removal
Registration sensor (MPF tray) removal
Registration sensor actuator removal
4-95
RIP cage
Separator roll removal
Static discharge brush removal
Stepper motor removal
Sub drive unit removal
4-104
Sub frame unit
Temperature and humidity sensor removal
4-56
theta sensor removal
Toner sensor removal
Torque limiter removal
Transfer belt motor removal
transfer belt position sensor removal
Transport sensor removal
Tray lift motor removal
Upper and lower registration springs removal
Waste toner sensor removal
I-4
Service Manual
4-90
4-92
4-190
4-91
4-93
4-29
4-31
4-175
4-200
4-202
4-199
4-33
4-37
4-203
4-110
4-196
4-68
4-199
4-198
4-42
4-105
4-197
4-182
4-179
4-94
4-43
4-196
,
4-55
4-37
4-106
4-184
4-179
4-180
4-183 4-197
,
4-180
4-200
4-84
4-101
4-97
4-181
4-100
4-41
4-198
4-201
4-181
4-112
removals
4-18
Back cave cover
4-6
Cord cover
Crossbar removal (not a FRU)
4-79
Drive unit
Drive unit motor C/M/Y/K
4-11
Front op panel cover
4-61
Fuser removal
4-19
Inner right cover
Left EMI shield removal (not a FRU)
Low volt power supply removal
4-58
Main switch
Op panel bottom cover
Op panel paper exit guide removal
4-13
Op panel top cover
Output bin (print engine top) cover
Output bin full sensor actuator removal
4-7
Rear cover
4-73
RIP board removal
4-5
RIP cover
Scanner power supply access cover
Scanner power supply removal
4-25
Speaker removal
4-40
Transfer belt – CRU
4-72
Transfer Roll - CRU
4-16
Upper right cover
3-11
Reports
3-25
Reset Calibration
3-20
Reset Calibration Values
4-73
RIP board removal
RIP board/operator panel replacement
4-95
RIP cage removal
S
ii-xv
safety information
6-1
safety inspection guide
scanner
2-35
lock
Scanner Calibration Reset
Scanner power supply removal
1-10
Selecting paper
Sensor Test
3-28
SCANNER
4-183
Separator roll removal
3-25
Serial Number
2-90
serial port service check
3-22
Serial Wrap Test
service check
2-56
840.03 service check
841.00 Invalid configuration or ASIC not found
841.01 Invalid AFE setting
841.02 Delayed interrupt detected
841.03 Failed indirect register test
841.05 Image pipe time-out
841.06 Scanner did not initiate scan
842.00 No response / 842.01 HW protocol / 842.02
2-58
Logical protocol
843.00 Carriage Home
844.00 Lamp failure (Front side)
849.01 Device had modem installed, but config ID
4-74
4-83
4-45
4-51
4-15
4-32
4-17
4-26
4-6
4-58
4-2
3-28
4-58
4-197
,
2-56
2-56
2-57
2-57
2-57
2-58
2-59
2-59