Visonic PowerMaster-10 Installer's Manual page 48

Option
26:SMS RCVR 1
27:SMS RCVR 2
Master Installer only
41:PSTN FORMAT
Master Installer only
46:PSTN RETRIES
47:GSM RETRIES
51:TEL AUTO TEST
52:AUTO TST TIME
53:COM.FAIL RPRT
PSTN FAIL
GSM/GPRS FAIL
(Return)
Previously known as
"LINE FAIL REPORT"
62:RECENT CLOSE
D-303222 PowerMaster-10/30 G2 Installer's Guide
Configuration Instructions
If equipped with GSM module, the PowerMaster can be programmed to report the event
messages defined in Report Events option (option 01) to two SMS Receivers via the GSM
SMS channel using a special SMS text format. For further details concerning the SMS text
format please contact Visonic.
Enter the two telephone numbers (including area code – maximum 16 digits).of the SMS
Receiver 1 located at the 1
nd
located at the 2 Monitoring Station (27:SMS RCVR 2).
Note: To enter the international prefix (
The PowerMaster can be programmed to report the event messages defined in Report
Events option (option 01) to two Alarm Format Receivers (see options 16 & 17) via PSTN
telephone line and/or GSM analog voice channel (if equipped with GSM module) using
standard PSTN alarm formats (i.e. SIA, Contact-ID and Scancom).
Select which of the reporting formats the system will use to report the events to the two Alarm
Format Receivers PSTN/GSM RCVR 1 and PSTN/GSM RCVR 2. The Event Codes used for
the reporting in each of the available formats are specified in APPENDIX D. Event Codes.
Make sure that the receivers used by the Monitoring Stations are of the compatible models
listed below and that the receiver used can receive the format you select.
Compatible Alarm Format Receivers:
Osborne-Hoffman model 2000; Ademco Model 685; FBII Model CP220; Radionics Model
D6500; Sur-Gard Model SG-MLR2-DG and Silent Knight Model 9500.
Options: SIA (default); Scancom; SIA text and contact ID.
Define the number of times the system will retry to report to the Monitoring Station in case of
failure to report via the PSTN telephone line connection.
Options: 2 attempts; 4 attempts (default); 8 attempts; 12 attempts and 16 attempts.
Define the number of times the system will retry to report to the Monitoring Station in case of
failure to report via the cellular connection - GPRS (IP), GSM and SMS.
Options: 2 attempts; 4 attempts (default); 8 attempts; 12 attempts and 16 attempts.
To verify a proper communication channel, the PowerMaster can be configured to send a test
event to the Monitoring Station via PSTN periodically. You can set the interval between the
consecutive test events or disable the automatic sending of this event entirely. If the interval is
set for every one day or more then the exact hour of reporting can be selected with option 52.
Options: test OFF (default); every 1/2/5/7/14/30 day(s); and every 5 hours.
Enter the exact time (auto test time) during the day at which the Auto Test message (if
enabled in option 51) will be sent to the Monitoring Station.
Note: If the AM/PM format is used, you can set the "AM" digit with the
the "PM" digit with the
Determine whether a failure in any of the system communication channels i.e. PSTN or
GSM/GPRS will be reported or not and the time delay between detection of the failure and
reporting of the failure event to the Monitoring Station. A trouble event (i.e. "tel line fail" or
"GSM line fail") will be respectively stored in the event log.
Options "PSTN FAIL": immediat report (default); after 5/30/60/180 min; and do not report.
Options "GSM/GPRS FAIL": after 2/5/15/30 min and do not report (default).
False alarms may occur if users do not exit the premises within the exit delay period,
resulting in a false alarm a short time later. In such cases, inform the Monitoring Station that
the alarm occurred shortly after the system was armed (this event is known as "Recent
Close"). The report enabled option sends a "recent closing" report to the Monitoring Station if
an alarm occurs within 2 minutes from the end of the exit delay.
Options: report disabled (default) and report enabled
st
Monitoring Station (26:SMS RCVR 1) and SMS Receiver 2
st

) at the 1
button.
5. PROGRAMMING

digit – key-in [#]
[1].
button and
47