Visonic PowerMaster-10 Installer's Manual page 33

5. PROGRAMMING
- Configuring New Devices


Location (name) setting:
[1]
To review or change the Location (name) setting, press the
[2]
To change the Location name, enter the menu and select the name from the "Location List" below. You can
assign additional custom names using the "06.CUSTOM NAMES" option in the Installer menu. See section 5.8.
Note: As a shortcut, press the 2 digit serial No. of the Location shown in the Location List above, which takes
you directly to its menu.
Zone Type setting:
[3]
To review or change the Zone Type setting, press the
[4]
The zone type determines how the system handles signals sent from the device. Press
suitable zone type. The list of available Zone Types and the explanation for each zone type is provided below.
Note: As a shortcut, press the 2 digit serial No. of the Zone Type shown in the Location List above, which
takes you directly to its menu.
Chime setting:
All zones are set to Chime OFF by default. To configure the device to cause the panel to sound (when disarmed)
[5]
a Chime melody when tripped, press the
Select between "Chime OFF", "melody-chime" and "zone name-chime"
[6]
panel sounds a chime melody when the sensor is tripped. In "zone name-chime" the control panel sounds the
zone name when the sensor is tripped. The chime operates during the Disarm mode only.
Partitions setting:
Note: The "PARTITIONS" menu appears only if Partitions is enabled in the control panel (see section 5.14).
When entering the menu, the display shows the default Partition selection (marked with ).
[7]
[8]
Use the keypad keys
Device Configuration:
[9]
To review or change the Device Configuration (settings), press the
option – see  [5].
[10] To configure the device parameters, refer to its corresponding device datasheet in the device Installation
Instructions. The defaults of the device parameters can be also configured as explained in section 5.4.6.
After completing the configuration of the device, the wizard brings you to the "Next Step" menu with the
[11]
following 3 options:
"NEXT Device" to enroll the next device.
"MODIFY Same Dev." reverts to Step 1 (i.e. "LOCATION") to allow you to perform additional changes to the
device, if needed.
"EXIT Enrollment" exits the enrollment procedure and returns to Step 1 bringing you back to the
"02:ZONES/DEVICES" menu.
Location List
No. Location Name
01 Attic
02 Back door
03 Basement
04 Bathroom
05 Bedroom
06 Child room
07 Closet
08 Den
Zone Type List
No. Zone Type
1. Exit/Entry 1
2. Exit/Entry 2
1
Refers to PowerMaster-30 G2 only
32
1
, ,
No. Location Name
09 Dining room
10 Downstairs
11 Emergency
12 Fire
13 Front Door
14 Garage
15 Garage door
16 Guest room
Description
This Zone starts the exit time when the user arms the system or the entry time when the
system is armed. To configure the Exit/Entry 1 time, see sections 5.5.1 & 5.5.2 - Installer
menu "03.CONTROL PANEL" options 01 and 03.
Same as Exit / Entry 1 but with a different delay time. Used sometimes for entrances closer to
the panel. For configuring the Exit and Entry 2 delays, see sections 5.5.1 & 5.5.2 –
Installer menu "03.CONTROL PANEL" options 02 and 03. (
button, otherwise scroll to the next option.
button, otherwise scroll to the next option.
button, otherwise scroll to the next option.
to change the status of the partitions P1, P2 & P3, respectively.
No. Location Name
17 Hall
18 Kitchen
19 Laundry room
20 Living room
21 Master bath
22 Master bedroom
23 Office
24 Upstairs
D-303222 PowerMaster-10/30 G2 Installer's Guide
1
. In "melody chime" the control
button, otherwise scroll to the next
No.
25
26
27
28
29
30
31
(∗)
∗
)
and select a
Location Name
Utility room
Yard
Custom 1
Custom 2
Custom 3
Custom 4
Custom 5