FujiFilm Frenic-Mini Instruction Manual page 26

Appli-
cable
motor Inverter type
rating
(kW)
0.1 FRN0.1C1 -2
0.2 FRN0.2C1 -2
0.4 FRN0.4C1 -2
0.75 FRN0.75C1 -2
1.5 FRN1.5C1 -2 **
2.2 FRN2.2C1 -2 **
3.7
FRN3.7C1 -2 **
0.4 FRN0.4C1 -4
0.75 FRN0.75C1 -4
1.5 FRN1.5C1 -4 **
2.2 FRN2.2C1 -4 **
3.7 FRN3.7C1 -4 **
4.0 FRN4.0C1 -4 **
0.1 FRN0.1C1 -7
0.2 FRN0.2C1 -7
0.4 FRN0.4C1 -7
0.75 FRN0.75C1 -7
1.5 FRN1.5C1 -7
2.2 FRN2.2C1 -7
0.1 FRN0.1C1 -6
0.2 FRN0.2C1 -6
0.4 FRN0.4C1 -6
0.75 FRN0.75C1 -6
*1 Use crimp terminals covered with an insulated sheath or insulating tube. Recommended wire sizes are
for HIV/IV (PVC in the EU).
*2 Wire sizes are calculated on the basis of input RMS current under the condition that the power supply
capacity and impedance are 500 kVA (50 kVA for single-phase 100 V series) and 5%, respectively.
*3 For single-phase 100V series of inverters, use the same size of wires as used for the main circuit
power input. Insert the DC reactor (DCR) in either of the primary power input lines. Refer to Chapter 10
for more details.
Note 1) A box ( ) in the above table replaces S or E depending on enclosure.
2) A box ( ) in the above table replaces A, C, E, or J depending on shipping destination.
3) Asterisks (**) in the above table denote the following:
21: Braking resistor built-in type, None: Standard
Table 2.6 Recommended Wire Sizes
Recommended wire size (mm
Main circuit power input
[L1/R, L2/S, L3/T]
[L1/L, L2/N]
Grounding [ G]
*2
w/ DCR w/o DCR
2.0 / 2.0
(2.5)
2.0 / 2.0
(2.5)
2.0 / 5.5
(2.5)
2.0 / 2.0 2.0 / 2.0
(2.5) (2.5)
2.0 / 2.0
(2.5)
2.0 / 2.0
(2.5)
2.0 / 3.5
(4.0)
2.0 / 3.5 3.5 / 5.5
(4.0) (6.0)
2.0 / 2.0
2.0 / 2.0
2.0 / 3.5
2-5
Main circuit
Inverter
DCR
output
[P1, P (+)]
[U, V, W]
2.0 / 2.0 2.0 / 2.0
(2.5) (2.5)
2.0 / 3.5 2.0 / 3.5
(2.5) (2.5)
2.0 / 2.0 2.0 / 2.0
(2.5) (2.5)
2.0 / 2.0
(2.5)
2.0 / 2.0
(2.5)
2.0 / 3.5
(4.0)
2.0 / 2.0 *3
*1
2
)
Braking Control
resistor circuit
[P (+), DB]
2.0 / 2.0
(2.5)
2.0 / 2.0
(2.5)
0.5
2.0 / 2.0
(2.5)
2.0 / 2.0
DCR: DC reactor