FujiFilm Frenic-Mini Instruction Manual page 17

Preface ................................................................ i
Safety precautions ................................................ ii
Precautions for use ............................................... x
How this manual is organized .................................xiii
Chapter 1 BEFORE USING THE INVERTER......1-1
1.1 Acceptance Inspection ...............................1-1
1.2 External View and Terminal Blocks.............1-2
1.3 Transportation ............................................1-2
1.4 Storage Environment ..................................1-3
1.4.1 Temporary storage.............................1-3
1.4.2 Long-term storage .............................1-3
Chapter 2 Mounting and Wiring of the Inverter ....2-1
2.1 Operating Environment...............................2-1
2.2 Installing the Inverter ..................................2-1
2.3 Wiring .........................................................2-2
2.3.1 Removing the Terminal Block (TB)
Covers ...............................................2-2
2.3.2 Terminal Arrangement and Screw
Specifications.....................................2-3
2.3.3 Recommended Wire Sizes ................2-4
2.3.4 Wiring Precautions.............................2-6
2.3.5 Wiring for Main Circuit Terminals and
Grounding Terminals..........................2-7
2.3.6 Replacing the Main Circuit Terminal
Block (TB) Cover .............................2-12
2.3.7 Wiring for Control Circuit Terminals .2-13
2.3.8 Switching of SINK/SOURCE
(Jumper Bar)....................................2-19
2.3.9 Installing an RS485 Communications
Card (Option) ...................................2-20
2.3.10 Replacing the Control Circuit Terminal
Block (TB) Cover .............................2-20
2.3.11 Cautions Relating to Harmonic
Component, Noise, and Leakage
Current.............................................2-21
Chapter 3 OPERATION USING THE KEYPAD....3-1
3.1 Keys, Potentiometer, and LED on the
Keypad .......................................................3-1
3.2 Overview of Operation Modes ....................3-2
3.2.1 Running Mode ...................................3-2
3.2.2 Programming Mode ...........................3-3
3.2.3 Alarm Mode .......................................3-4
3.3 Operation in Running Mode........................3-6
3.4 Setting the Function Codes--
"Data setting"............................................3-12
3.5 Checking Changed Function Codes--
"Data checking" ........................................3-15
3.6 Monitoring the Running Status--
"Drive monitoring".....................................3-16
3.7 Checking I/O Signal Status--
"I/O checking" ...........................................3-20
3.8 Reading Maintenance Information--
"Maintenance information"........................3-23
3.9 Reading Alarm Information--
"Alarm information"...................................3-25
Chapter 4 RUNNING THE MOTOR.....................4-1
4.1 Running the motor for a test .......................4-1
4.1.1 Inspection and Preparation prior to
the Operation .....................................4-1
4.1.2 Turning on Power and Checking........4-1
4.1.3 Preparation before running the motor
for a test--Setting function code data .4-2
4.1.4 Test run..............................................4-3
Table of Contents
4.2
Chapter 5 FUNCTION CODES ........................... 5-1
5.1 Function Code Tables ................................ 5-1
5.2 Overview of Function Codes .................... 5-13
Chapter 6 TROUBLESHOOTING ....................... 6-1
6.1 Before Proceeding with Troubleshooting.... 6-1
6.2 If no alarm code appears on the
LED monitor ............................................... 6-3
6.2.1 Motor is running abnormally .............. 6-3
6.2.2 Problems with inverter settings ......... 6-7
6.3 If an alarm code appears on the LED
monitor ....................................................... 6-9
Chapter 7 MAINTENANCE AND INSPECTION .. 7-1
7.1 Daily Inspection.......................................... 7-1
7.2 Periodic Inspection..................................... 7-1
7.3 Measurement of Electrical Amounts in
Main Circuit ................................................ 7-6
7.4 Insulation Test ............................................ 7-7
7.5 List of Periodical Replacement Parts ......... 7-8
7.6 Inquiries about Product and Guarantee ..... 7-8
Chapter 8 SPECIFICATIONS .............................. 8-1
8.1 Standard Models ........................................ 8-1
8.1.1 Three-phase 200 V Series ................ 8-1
8.1.2 Three-phase 400 V Series ................ 8-2
8.1.3 Single-phase 200 V Series................ 8-3
8.1.4 Single-phase 100 V Series................ 8-4
8.2 Models Available on Order ......................... 8-5
8.2.1 EMC Filter Built-in Type..................... 8-5
8.2.2 Braking Resistor Built-in Type ........... 8-5
8.3 Common Specifications.............................. 8-6
8.4 Terminal Specifications............................... 8-8
8.4.1 Terminal Functions ............................ 8-8
8.4.2 Connection Diagram in Operation by
8.5 External Dimensions ................................ 8-10
8.5.1 Standard Models and Models Available
8.5.2 Models Available on Order (Built-in
8.6 Protective Functions................................. 8-14
Chapter 9 LIST OF PERIPHERAL EQUIPMENT
Chapter 10 APPLICATION OF DC REACTOR
Chapter 11 CONFORMITY TO STANDARDS ..... 11-1
11.1 Conformity to UL standards and Canadian
standards (cUL certification)..................... 11-1
11.1.1 General Descriptions....................... 11-1
11.1.2 Considerations when using
11.2 Conformity to European Standards .......... 11-1
11.3 Conformity to EMC Standards.................. 11-2
11.3.1 Scope .............................................. 11-2
11.3.2 Recommended Installation .............. 11-2
11.4 Harmonic Component Regulation in EU .. 11-4
11.4.1 General comments .......................... 11-4
11.4.2 Conformity to Harmonic Component
xv
Operation .......................................... 4-3
External Signal Inputs ....................... 8-8
on Order (Built-in Braking Resistor
Type) ............................................... 8-10
EMC Filter Type) ............................ 8-12
AND OPTIONS................................... 9-1
(DCRs) ............................................. 10-1
FRENIC-Mini in systems to be
certified by UL and cUL ................... 11-1
Regulation ....................................... 11-5