Intermec JANUS 2020 User Manual page 565

JANUS 2020 Hand-Held Computer User's Manual (4MB)
IRL programs, running, 10-17
MakeDisk, using, 10-25
operating the reader, 10-7 to 10-13
PC cards, using, 10-7, 10-19 to 10-21
powering up the reader, 10-3 to 10-6
reader locks-up, 9-5
scanner, turned off, 10-9, 10-33
scanning bar code labels, 10-30
turning on the reader, 10-4
TSR
Reader Wedge, 3-40
Turnaround Delay command, 12-95
turning the reader on and off, 1-12, 10-4
Type I card, using, 4-4
Type II card, using, 4-4
Type II PC card drive, See PC card drive
Type III card, defined, 4-4
U
UART FIFO control register
configuring for COM port, 6-20, 12-37
troubleshooting, 10-15
UCC/EAN Code 128, enabling, 12-28
Universal Product Code, See UPC/EAN command
unloading protocol handlers, 6-15 to 6-19
unpacking the JANUS 2020, 1-6
UPC/EAN command, 12-96
UPC-A/EAN-13, enabling, 12-96
UPC-E, enabling, 12-96
upgrading
flash memory, 9-13
upper memory block, described, A-16
uppercase letters, bar code labels to scan, C-20
user flash memory, described, A-18
User-Defined protocol
defined, 6-11
Multi-Drop, configuring, 12-42
parameters, configuring, C-6
parameters, list of, 6-15, 12-39
POL and SEL combinations, C-7
using the manual, xxi
V
variable data, entering in configuration commands, 12-6
verifying the reader's operation, 1-11
vertical steps, setting for viewport, 12-100
video modes
choosing, 2-21
configuring, 12-48
viewport
cursor, moving to, reader command, 11-19
down, reader command, 11-15
end, reader command, 11-17
home position, defined, 2-23
I-20
home, reader command, 11-18
icon, 2-23, 2-30
Intersvr status screen, viewing, 6-35
left, reader command, 11-16
moving, 2-23 to 2-27, 6-35
automatic or manual mode, configuring, 2-27,
12-99
automatic or manual mode, using, 2-25
cursor to viewport, 2-27
keys, enabling or disabling, 12-99
reader commands, using, 11-15 to 11-20
size of steps, configuring, 12-100
steps, defined, 2-25
viewport to cursor, 2-27
page down, reader command, 11-18
page up, reader command, 11-19
right, reader command, 11-17
troubleshooting, 10-8
up, reader command, 11-16
Viewport Movement Keys command, 12-99
Viewport Movement Mode command, 2-25, 12-99
Viewport Movement Steps command, 2-25, 11-15 to
11-17, 12-100
virtual display
configuring to use, 12-48
defined, 2-23, 11-15
moving the viewport, 2-23
using, 12-99, 12-100
Virtual Wedge
configuring, 3-42
disabling, 3-43
enabling, 3-42
volume, adjusting the beep, 2-27, 12-15
voting, Scanner Redundancy command, 12-86
VT100/220/320 and ANSI terminal emulation option,
1-5
W
warm boot
executing, 9-3
prohibiting, 12-70
warnings, xx
X
X4P, IRL command, 6-8
XON/XOFF, set by flow control, 12-56
Y
yellow laser scanner trigger, 2-45
yellow button, 1-12
Z
Z, IRL command, configuring the reader, 5-13