Intermec JANUS 2020 User Manual page 560

insufficient to run applications, 10-7, 10-17
making available on the reader, 3-39 to 3-40
overlapping ranges, EMM386, 10-22
RAM drives, using, 3-34
storing data, recommended uses, 2-44
upper memory block, described, A-16
memory card
illustrated, 4-4
reader accessory, 1-4
types recommended, 4-5
menu, MCFORMAT, 4-15
menu, Startup, 3-11, 3-39
messages
Bad BIOS Checksum, 9-13, 10-5
Bad command or filename, 10-7, 10-19, 10-30
Bad Saved State, 10-5, 10-6, 10-13
conventions for manual, xxiv
File not found, 10-7
Invalid media type reading drive X, 10-19
Not ready reading drive X, 10-7, 10-19
Write Fault Error Writing Device PRN, 10-22
XX Keyboard Error, 10-4
mixed-full ASCII, Code 39, 12-21
mode, Suspend, 6-20, 7-17
models, for the reader, 1-5
modem card
illustrated, 4-4
reader accessory, 1-4
modifiers, using on international keypads, 8-12
Monochrome Video mode, 12-48
moving the viewport
cursor to viewport, 11-20
down, 11-15
learning how to, 2-25
left, 11-16
lower right corner, 11-17
page down, 11-18
page up, 11-19
reader commands, using, 11-15 to 11-20
right, 11-17
to the cursor, 11-19
up, 11-16
upper right corner, 11-18
MS-DOS, See DOS
MS-Flash
formatting flash cards, 4-17
MSI command, 12-72
MTAA.EXE, 10-20
MTAB.EXE, 10-20
Multi-Drop protocol
address, configuring, 12-7
baud rate, configuring, 12-11
defined, 6-10
parameters, list of, 6-14, 12-38
troubleshooting, 10-15
User-Defined, configuring, 12-39
User-Defined, POL and SEL combinations, C-7
Multiple-Read labels, defined, 12-34
N
National Language Support, See DOS NLS
NEG command, 12-74
Negative Acknowledge, See NEG command
network port, communications dock, 12-35
networking
application, choosing, 6-10
BFT, downloading applications, 6-42 to 6-53
COM port, selecting, 6-13, 12-36
Communications Manager, using, 6-37 to 6-42
configuring the reader, 6-13
connecting the reader to a device, 6-23
CrossBar, Multi-Drop protocol, 6-10, 6-14
illustrated, 6-3
Interlnk
executing on the host computer, 6-30
executing on the reader, 6-32
installing, 6-29
planning the connection, 6-9
protocol handler, loading and unloading, 6-15 to 6-19
protocol, activating, 6-15, 12-41
protocol, configuring, 6-14, 12-38
troubleshooting, 10-15
UART FIFO control register, setting, 6-20, 12-37
Next button
Communications Manager screens, 6-41
IC.EXE screens, 5-10
NiCad battery pack, See battery pack
NLS, See DOS NLS
NMI, do not mask, 10-12
No Protocol, 6-10
non-full ASCII, Code 39, 12-21
non-maskable interrupt, See NMI
notches, on PC cards, 4-7
Num Lock, determining the status of, 2-16
number pad
ASCII characters, entering, 2-16
enabling or disabling entry to, 12-71
international keypads, using, 8-13
key combinations, list of, B-6, B-11
status, determining, 2-16, 10-8
using, 2-13
numbers, bar code labels to scan, C-20
numeric keypad, See number pad
Numeric Keypad command, 12-71
O
O, IRL Open command, 7-15
Off, Boot Loader menu, 9-7
One-Shot mode, configuring the scanner, 12-85
I
Index
I-15