Modular Optics Compatibility - Cisco ASR 1000 Series Hardware Installation Manual

Chapter 1 SIP and SPA Product Overview
Table 1-5
SPA
Cisco WebEx Node for ASR 1000
Series
Cisco DSP SPA for ASR 1000
Series
Table 1-6
SPA
1-Port Channelized OC3/STM-1
ATM and Circuit Emulation SPA
2-Port Channelized T3/E3 ATM
CEoP SPA
24-Port Channelized T1/E1 ATM
CEoP SPA
1. Restriction: The SPA-1CHOC3-CE-ATM is not supported on the Cisco ASR 1001 Router (1 RU chassis), but supported on
2. Restriction: Effective from Cisco IOS XE Release 3.4.0S, the SPA-2CHT3-CE-ATM is supported on all the Cisco ASR 1000
3. Restriction: The SPA-24CHT1-CE-ATM is not supported on the Cisco ASR 1001 Router (1 RU chassis), but supported on

Modular Optics Compatibility

Some SPAs implement small form-factor pluggable (SFP) optical transceivers to provide network
connectivity. An SFP module is a transceiver device that mounts into the front panel to provide network
connectivity.
Cisco qualifies the SFP modules that can be used with SPAs.
OL-14126-15
SIP and SPA Compatibility for Service SPAs
SIP and SPA Compatibility for CEoP SPA
2
3
all other ASR 1000 chassis. All the other ASR 1000 Routers support the SPA-1CHOC3-CE-ATM for Circuit Emulation
application; but not ATM applications. Effective from Cisco IOS XE Release 3.3.0S, the SPA-1CHOC3-CE-ATM is
supported only with these software images: ADVANCED ENTERPRISE SERVICES, ADVANCED ENTERPRISE W/O
CRYPTO, ADVANCED IP SERVICES, or ADVANCED IP SERVICES W/O CRYPTO. The SPA-1CHOC3-CE-ATM is
not supported with these software images: IP BASE and IP BASE W/O CRYPTO.
Series Routers except on the Cisco ASR 1001 Router. However, the SPA-2CHT3-CE-ATM supports only the T3 ATM mode
in Cisco IOS XE Release 3.4.0S and not the Circuit Emulation (CEM) mode. Maximum Virtual Circuits supported are 1024.
Interim Local Management Interface (ILMI) 1.0 is not supported. IETF RFC 2364 and 2516 for Point-to-Point Protocol
(PPP) over ATM is not supported. IETF RFC 1577 support for classical IP and Address Resolution Protocol (ARP) over
ATM is not supported. ATM Forum UNI 3.0, 3.1, and 4.0 is not supported. Effective from Cisco IOS XE Release 3.5.0S,
the SPA-2CHT3-CE-ATM supports ATM on clear-channel E3 SPA. All the existing ATM features are supported in the E3
mode. Effective from Cisco IOS XE Release 3.8.0S, the SPA-2CHT3-CE-ATM is supported on the Cisco ASR 1001 Router.
The SPA-2CHT3-CE-ATM on the Cisco ASR 1001 Router supports both the T3 and E3 ATM modes and does not support
the CEM mode.
all other ASR 1000 chassis. Effective from Cisco IOS XE Release 3.4.0S, the SPA-24CHT1-CE-ATM supports only the
CEM mode. Effective from Cisco IOS XE Release 3.4.0S, the SPA-24CHT1-CE-ATM is supported only with these software
images: ADVANCED ENTERPRISE SERVICES, ADVANCED ENTERPRISE W/O CRYPTO, ADVANCED IP
SERVICES, or ADVANCED IP SERVICES W/O CRYPTO. The SPA-24CHT1-CE-ATM is not supported with these
software images: IP BASE and IP BASE W/O CRYPTO.
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide
SIP Supported:
Product ID Cisco ASR1000-SIP10
SPA-WMA-K9 Yes
SPA-DSP Yes
Product ID
SPA-1CHOC3-CE-ATM Yes
1
SPA-2CHT3-CE-ATM
SPA-24CHT1-CE-ATM
Modular Optics Compatibility
SIP Supported:
Cisco ASR1000-SIP40
Yes
Yes
SIP Supported: SIP Supported:
Cisco Cisco
ASR1000-SIP10 ASR1000-SIP40
Yes
Yes Yes
Yes Yes
1-5