Preparing For Online Removal Of A Spa; Deactivating A Spa - Cisco ASR 1000 Series Hardware Installation Manual

Chapter 5 Installing and Removing a SIP
--------- ------------------- --------------------- -----------------
0
1
1/1
2
2/1
2/3
3
3/3
4
4/2
4/3
5
R0
R1
F0
P0
P1
P2
P3
Slot
--------- ------------------- ---------------------------------------
0
1
2
3
4
5
R0
R1
F0

Preparing for Online Removal of a SPA

The Cisco 7600 series router support the OIR of a SPA independent of removing the SIP. This means
that a SIP can remain installed in the Cisco ASR 1000 Series Router with one SPA remaining active,
while you remove another SPA from one of the SIP subslots. If you are not planning to immediately
replace a SPA into the SIP, ensure that you install a blank filler plate in the subslot. The SIP should
always be fully installed with either functional SPAs or blank filler plates.
If you are planning to remove a SIP along with its SPAs, you do not have to follow the instructions
provided in this section. To remove a SIP, see the
page

Deactivating a SPA

Although graceful deactivation of a SPA is recommended using the hw-module subslot stop command
in EXEC mode, the Cisco 7600 series router support the removal of the SPA without deactivating it first.
Before deactivating a SPA, ensure that the SIP is seated securely in the slot before you pull out the SPA.
Note If you are preparing for an OIR of a SPA, it is not necessary to independently shut down each of the
interfaces prior to deactivation of the SPA. The hw-module slot stop command in EXEC mode
automatically stops traffic on the interfaces and deactivates them along with the SPA in preparation for
OIR. In similar fashion, you do not need to independently restart any interfaces on a SPA after OIR of a
SPA or SIP.
OL-14126-15
ASR1000-SIP10
ASR1000-SIP40
SPA-5X1GE-V2
ASR1000-SIP40
SPA-1X10GE-L-V2
SPA-1X10GE-L-V2
ASR1000-SIP40
SPA-4XT3/E3
ASR1000-SIP40
SPA-5X1GE-V2
SPA-4XCT3/DS0
ASR1000-SIP40
ASR1000-RP2
ASR1000-RP2
ASR1000-ESP40
ASR1013-PWR-AC
ASR1013-PWR-AC
ASR1013-PWR-AC
ASR1013-PWR-AC
CPLD Version
00200800
00200800
00200800
00200800
00200800
00200800
10021901
10021901
1001270D
5-2.
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide
ok 1w0d
ok 1w0d
ok 1w0d
ok 1w0d
ok 1w0d
ok 1w0d
ok 1w0d
ok 1w0d
ok 1w0d
ok 1w0d
ok 1w0d
ok 1w0d
ok, active 1w0d
ok, standby 1w0d
ok, active 1w0d
ok 1w0d
ps, fail 1w0d
ok 1w0d
ps, fail 1w0d
Firmware Version
15.0(1r)S
15.0(1r)S
15.0(1r)S
15.0(1r)S
15.0(1r)S
15.0(1r)S
15.0(1r)S
15.0(1r)S
15.0(1r)S
"Preparing for Online Removal of a SIP" section on
Online Insertion and Removal
5-5