Error Messages - Yamaha A4000 Owner's Manual

Error Messages

Here is a list of the error messages that will appear when an incorrect operation is performed or when a setting is incorrect.
Audio CD is required.
Audition requires more memory.
Bulk data error.
Bulk protect switch is ON.
Cannot copy Volume to FD.
Cannot create sample (>16MW).
Cannot find associated file.
Cannot find disk.
Cannot find CD-R.
Cannot find file.
Cannot find SCSI or IDE disk.
Cannot revert this sample.
Cannot write to this disk.
CD-R size overflow.
DIG or OPT signal input is required.
Disk drive is not ready.
Disk is duplicated in list.
Disk is not formatted.
Disk is write protected.
Disk read/write error.
File is being accessed.
MIDI buffer is full.
MIDI is busy.
MIDI receive error.
Name already exists.
Non-existent track or index.
Not enough disk area or
too many items.
Param memory full or
too many samples.
Please set device number.
Sample Bank is selected in list.
Sample processing failed.
SIMM configuration error.
SCSI terminator or device error.
Some samples are copy protected.
Too many samples.
Too many takes.
Try physical format.
Unknown disk or file format.
Unsupported file format.
Unsupported file name.
Unsupported sampling frequency.
Verification error.
Wave memory error.
Wave memory full.
An audio CD is not loaded into the external CD-ROM drive.
There is not enough wave memory available to use the AUDITION function. Direct playback from the disk is
not possible.
Processing of a bulk dump failed.
Bulk data or a SCSI message was received when the bulk protect switch was "on."
Cannot copy a volume unit to a floppy disk.
An attempt was made to create a sample larger than 16 Mwords (32 megabytes).
The voice file associated with the voice data could not be located.
Not ready for disk operation.
Cannot prepare the CD-ROM drive for operation.
The specified file does not exist.
SCSI or IDE disk could not be found.
The revert function cannot be used with newly created samples which have not been saved or imported
samples.
An attempt has been made to write to an unwriteable CD-ROM or other disk.
The data to be written exceeds the capacity of the CD-R disk.
No digital signal is present at the DIGITAL IN or OPTICAL IN terminal.
The disk is not ready for saving or loading.
Duplicate backup source disks have been specified.
The disk is not formatted for the A5000/A4000.
The disk is write protected, and writing could not be performed.
An error occurred while reading or writing to/from disk.
You attempted to access a file which was undergoing some type of processing.
The A5000/A4000's processing was not able to keep up with MIDI input.
You attempted to execute a bulk dump from the front panel while a bulk dump or parameter change etc.
was being processed.
A MIDI receive error occurred.
A file on disk or in memory with the specified name already exists.
The audio CD loaded into the external CD-ROM drive does not have the specified track number or index
number.
There is not enough disk space to complete the operation, or the total number of samples/sample banks
which can be saved to disk has been exceeded.
The operation cannot be completed because not enough parameter memory is available, or the number of
samples, sample banks, etc., which can be retained in memory has been exceeded.
Transmission or reception of bulk data was attempted with the device number turned off.
Sample banks cannot be written to an audio CD.
When executing a waveform processing command, the specified command could not be executed due to
insufficient free space in the work area of wave memory, or for some other reason.
The A5000/A4000 was not able to start up, due to the fact that expansion SIMM's are not installed in pairs,
or because the usage order of the expansion slots is incorrect etc.
A SCSI error has occurred. Check terminators and connections and try again.
You have attempted to export or write copy-protected samples to an audio CD.
The operation cannot be completed because the number of target samples is too great. Up to 128 samples
can be arranged at one time, and the maximum number of samples that can be contained in a sample
bank is 127.
The sample could not be created, either because the maximum number of 64 was exceeded when consec-
utively recording with New+, or because an identically-named sample already exists.
Logical formatting failed. Try physical formatting.
Either the contents of the file have been damaged, or it is the wrong format.
The file is corrupted, or has an unsupported format.
The file name could not be detected by the A5000/A4000.
Samples that do not have a 44.1 kHz sampling rate cannot be written to an audio CD.
A verification error occurred while writing to disk.
An error occurred in wave memory.
The specified command could not be executed due to insufficient free space in wave memory.
Error Messages
273
Appendix
A5000/A4000 •