Yamaha A4000 Owner's Manual page 126

EDIT-TRIM/LOOP
Knob 4
[ Turn] Remix Zone Start
The Remix Zone to be affected by the Loop Remix func-
tion is determined by the settings of the Remix Zone Start
parameter (Knob 4) and the Remix Zone End parameter
(Knob 5). This allows the Loop Remix function to be
applied to only a specified section of the loop within the
selected sample.
[Range] The specified loop of the selected sample is
divided into 8 "areas," and the Remix Zone Start
parameter can be set from the first area up one
before the last area.
• The selected area can be played back by pressing
the ZONE MONITOR knob (Knob 3).
[ Press] REGISTER...
Allows the currently displayed remix pattern to be regis-
tered as a user Remix Type (User1 — User5).
When the REGISTER... knob is pressed the following
pop-up window will appear:
Rotate the knob to select User1 — User5, then press the
knob to register the remix pattern to that Remix Type.
Move the cursor to CANCEL and press the knob to close
the pop-up window without registering the remix pattern.
• If only a portion of a loop has been specified as the
remix zone and REMIX executed, the REGISTER
function cannot be executed.
• The REGISTER... function cannot be used if the
REMIX knob (Knob 2) has not been pressed since
the CREATE function was executed or the A5000/
A4000 power was turned on.
Knob 5
[ Turn] Remix Zone End
The Remix Zone to be affected by the Loop Remix func-
tion is determined by the settings of the Remix Zone Start
parameter (Knob 4) and the Remix Zone End parameter.
This allows the Loop Remix function to be applied to only
a specified section of the loop within the selected sample.
[Range] The selected sample loop is divided into 8
"areas," and any of these from the 2nd to last
area can be specified as the Remix Zone End.
• The selected area can be played back by pressing
the ZONE MONITOR knob (Knob 3).
[ Press] CREATE
When a satisfactory remix has been achieved by pressing
the REMIX knob (Knob 2), press the CREATE knob to
actually save temporary "working sample" produced by
the remix operation as an normal sample. "Working:" will
appear to the left of the name of the new sample created
by the CREATE function.
126
Chapter 5 EDIT Mode
• A5000/A4000
• The CREATE function cannot be used if the REMIX
knob (Knob 2) has not been pressed since the CRE-
ATE function was previously executed or the A5000/
A4000 power was turned on.
Cursor w
Cursor
w
Knob 1 Knob 2
Turn
Cursor/Page —
action
Press
Tree View REMIX
action
Knob 1
Same function as Cursor
Knob 2
[ Press] REMIX
The Loop Remix function is executed when this knob is
pressed, and the results are temporarily stored in mem-
ory as a "working sample." If the REMIX button is
pressed again the Loop Remix function will be executed
again and the previous results erased.
You can execute the REMIX function as many times as
necessary until satisfactory results are achieved. When
Remix Type 1 — 5 is selected, different results will be
achieved each time REMIX is executed even if the same
Remix Type Variation is selected. When satisfactory
results have been achieved and the CREATE function is
executed (Knob 5), the Working Sample is stored as a
normal sample. If the AUTO AUDITION function is on
(Knob 3) the result of each remix operation will be
automatcially played back after REMIX is executed. Fur-
ther, the Working Sample can be monitored by pressing
the [AUDITION] button.
• This parameter cannot be edited when a sample
bank is being edited.
Knob 3
[ Turn] Auto Audition
Determines whether the results of the Loop Remix func-
tion will automatically be played back or not.
[Range] off, on
• off ... No playback.
• on ... Automatic playback.
[ Press] ZONE MONITOR
Plays back only the remix zone (from the specified Remix
Zone Start to Remix Zone End) without playing the rest of
the loop.
• This parameter cannot be edited when editing a
sample bank.
Knob 4, 5
Same function as Cursor
Knob 3 Knob 4 Knob 5
Remix Zone Remix Zone
Auto Audition
Start End
ZONE
REGISTER CREATE
MONITOR
q
(page 125).
q
(page 125).