Yamaha A4000 Owner's Manual page 114

PLAY-CONTROL
Knob 4
[ Turn] Program LFO Tempo
Specifies the tempo on which the program LFO speed
will be based. The actual LFO speed is determined by the
setting of this parameter and the Program LFO Cycle
parameter (when the Program LFO Sync parameter is set
to "Manual").
[Range] 25 — 250
• This parameter cannot be edited when the Program
LFO Sync parameter is set to MIDI-A or MIDI-B
(MIDI on the A4000).
[ Press] QUICK...
Calls the quick entry menu (page 83).
Knob 5
[ Turn] Program LFO Cycle
Determines the LFO cycle in relation to the tempo set by
the Program LFO Tempo parameter.
e q e
[Range] , , x 3,
e e e e
" " produces the fastest LFO cycle (twice the
Program LFO Tempo setting), while "
duces the slowest LFO cycle (1/16th the Pro-
gram LFO Tempo setting).
Cursor w
Cursor
w
Knob 1 Knob 2
Turn Program LFO
Cursor/Page
action Initial Phase
Press
Tree View —
action
Knob 1
Same function as Cursor
Knob 2
[ Turn] Program LFO Initial Phase
Specifies the phase angle at which the progam LFO cycle
begins.
[Range] 0°, 90°, 180°, 270°
0°
114
Chapter 4 PLAY Mode
q q q q
x 2, x 4, x 8, x 16
q q q q
x 16" pro-
Knob 3 Knob 4 Knob 5
Program LFO Program LFO
Phase Reset — Phase Reset
Ch Note
MIDI — MIDI
q
(page 113).
90°
• A5000/A4000
180°
• The Program LFO Initial Phase setting becomes
effective when a Program LFO Reset Channel com-
mand is received, or if the Program LFO Sync
parameter is set to MIDI-A or MIDI-B (MIDI on the
A4000).
Knob 3
[ Turn] Program LFO Phase Reset Ch
Specifies the MIDI channel on which phase reset note
data (Program LFO Phase Reset Note) will be received.
[Range] off, AUD, A01 — B16 (01 — 16 on the A4000),
Bch
• off ... No phase reset occurs even if note-on data is
received.
• AUD ... The LFO phase is reset when the panel
[AUDITION] bnutton is pressed.
• A01 — B16, Bch (basic receive channel) ... The
phase will be reset when a Program LFO
Reset Note is received on the specified chan-
nel.
[ Press] MIDI
Allows the Program LFO Phase Reset Channel to be set
directly from an external MIDI device (page 82).
• When setting the MIDI channel via MIDI on the
A5000, receive the appropriate MIDI messages via
the MIDI IN-A connector to set channels A01 — A16,
and via the MIDI IN-B connector to set channels B01
— B16.
Knob 5
[ Turn] Program LFO Phase Reset Note
Specifies the note(s) which will be used to reset the
phase of the Program LFO.
[Range] all, C-2 — G8
• all ... The Program LFO phase will be set by any
note received via the Program LFO Phase
Reset channel.
• C-2 — G8 ... The Program LFO phase will be set
by notes in the specified range received via
the Program LFO Phase Reset channel.
• This parameter cannot be edited when Program LFO
Sync is set to MIDI-A or MIDI-B (MIDI on the A4000).
• This parameter cannot be edited when Program LFO
Sync is set to Manual, or the Program Phase Rest
Channel is set to off or AUD.
[ Press] MIDI
Allows the parameter to be set directly by receiving an
appropriate MIDI message from an external MIDI device
(page 82).
270°