Yamaha A4000 Owner's Manual page 152

RECORDING-RECORD
When the GO Knob (Knob 5) Is Pressed From the
Record Ready Display
Knob 1 Knob 2
Turn
— —
action
Press
— —
action
In this state recording will begin the instant Knob 4 (START) is
pressed. If "Edge/Manual" triggering has been selected via the
TRIGGER page (page 158), recording will start automatically as
soon as the input signal exceeds the set start edge trigger level.
• If you have set up to record from an audio CD loaded into a CD-
ROM drive connected to the A5000/A4000 via the EXT CTRL dis-
play (page 161), playback of the audio CD will start automatically
as soon as Knob 4 (START) is pressed.
• The Knob 3 (PAUSE) function will only be available if the "New+,"
Record Type has been selected.
The following display will appear while recording is in
progress.
When the "New" or "Replc" Record Type is selected.
If the "Replc" or "New" Record Type has been selected via the
SETUP display (page 153), the following display will appear
while recording is in progress.
Knob 1 Knob 2
Turn
— —
action
Press
— —
action
In this state recording will stop and the sampler will return to the
record ready display when Knob 5 (FINISH) is pressed. If
"Edge/Manual" triggering has been selected via the TRIGGER
page (page 159), recording will stop automatically as soon as the
input signal level drops below the set stop edge trigger level, and
the sampler will return to the record ready display.
If you press Knob 3 (ABORT) during recording, recording will
be cancelled and the sampler will return to the record ready dis-
play.
• If you have set up to record from an audio CD loaded into a CD-
ROM drive connected to the A5000/A4000 via the EXT CTRL dis-
play (page 161), playback of the audio CD will stop automatically as
soon as Knob 5 (FINISH) or Knob 3 (ABORT) is pressed.
152
Chapter 6 RECORD Mode
Knob 3 Knob 4 Knob 5
— — —
PAUSE START FINISH
Knob 3 Knob 4 Knob 5
— — —
ABORT — FINISH
• A5000/A4000
When the "New+" Record Type is selected.
If the "New+" Record Type has been selected via the SETUP dis-
play (page 153), the following display will appear while record-
ing is in progress.
Knob 1 Knob 2
Turn
— —
action
Press
— STOP
action
In this state recording will stop and the sampler will return to the
record standby display ready to record the next sample when
Knob 2 (STOP) is pressed. If "Edge/Manual" stop triggering has
been selected via the TRIGGER page (page 159), recording will
stop automatically as soon as the input signal level drops below
the set stop edge trigger level, and the sampler will return to the
record standby display ready to record the next sample.
If Knob 3 (>SKIP) is pressed during recording, recording of the
current sample will be cancelled and the sampler will return to
the record standby display ready to record the next sample.
Recording will stop completely and the sampler will return to the
record ready mode when Knob 5 (FINISH) is pressed.
If "Edge/Manual" start triggering has been selected via the
TRIGGER page (page 158), recording will stop when either
Knob 2 (>STOP) or Knob 3 (>SKIP), and the following display
will appear while the sampler waits for the input signal to drop
below the specified stop trigger level before recording of the next
sample can begin.
Knob 1 Knob 2
Turn
— —
action
Press
— STOP
action
When the input signal level has dropped below the stop edge trig-
ger level, the sampler will automaticaly return to the record
standby display, ready to record the next sample. While the sam-
pler is waiting for the input signal to decay below the stop trigger
level it is possible to immediately force recording of the next
sample to start by pressing Knob 4 (>START).
• Knob 4 (>PAUSE) can be pressed to temporarily pause recording
(recording will not re-start even if the input signal level exceeds the
specified start trigger level). Press Knob 4 (>CONTINUE) a second
time to resume recording.
• When recording from an audio CD loaded in a CD-ROM drive con-
nected to the A5000/A4000, the next index on the CD is automati-
cally selected when Knob 2 (>STOP) or Knob 3 (>SKIP) is pressed.
If there is no index, or recording was stopped during playback of the
last index on the track, the next track will be selected for playback.
CD playback will stop when Knob 5 (>FINISH) is pressed.
Knob 3 Knob 4 Knob 5
— — —
SKIP — FINISH
Knob 3 Knob 4 Knob 5
— — —
SKIP START FINISH