Yamaha A4000 Owner's Manual page 262

Effect Parameter List
34: CLIPPER1
1 Drive 0 — 100
2 Drive Output Level 0 — 100
@3 Clip Band Lo, Hi
4 Cutoff Freq 32Hz — 18.0kHz
5 Clip Type TypeA,TypeB,TypeC,TypeD
Noise may be produced with some voices when the "4. Cutoff Freq" is varied rapidly.
35: CLIPPER2
1 Drive 0 — 100
2 Drive Output Level 0 — 100
@3 Clip Band Lo, Hi, Mid, Lo&Hi
4 Cutoff Freq 32Hz — 18.0kHz
5 Mid Band Width 1 — 32
6 Clip Type TypeA,TypeB,TypeC,TypeD
7 Dry/Wet Balance D63>W — D=W — D<W63
Noise may be produced with some voices when the "4. Cutoff Freq" is varied rapidly.
36: NOISE GATE
1 Threshold -72dB — -30dB
2 Attack 1ms — 40ms
3 Release 10ms — 680ms
4 Output Level 0 — 127
37: V-DISTORTION
1 Over Drive 0 — 100%
@2 Device Transister,Vintage Tube,Dsitortion1,2, Fuzz
@3 Speaker Type Flat, Stack, Combo,Twin,Radio,Megaphone
4 Presence -10 — 10
5 Output Level 0 — 127
6 Delay Mix 0 — 127
7 Delay Time L 0.1ms — 1480.0ms
8 Delay Time R 0.1ms — 1480.0ms
9 Feedback Time 0.1ms — 1480.0ms
10 Feedback Level -63 — +63
11 Dry/Wet Balance D63>W — D=W — D<W63
38: DISTORTION, 39: OVERDRIVE
1 Drive 0 — 127
2 EQ Low Frequency 32Hz — 2.0kHz
3 EQ Low Gain -12dB — +12dB
4 LPF Cutoff Freq 1.0kHz — 18.0kHz, thru
5 Output Level 0 — 127
6 Edge 0 — 127
7 EQ Mid Frequency 100Hz — 10.0kHz
8 EQ Mid Gain -12dB — +12dB
9 EQ Mid Width 1 — 12.0
10 Dry/Wet Balance D63>W — D=W — D<W63
40: AMP SIMULATOR
1 Dry/Wet Balance D63>W — D=W — D<W63
2 Drive 0 — 127
@3 AMP Type Off, Stack, Combo,Tube
4 LPF Cutoff Freq 315Hz — 18.0kHz, thru
5 Edge 0 — 127
6 Output Level 0 — 127
41: STEREO DISTORTION, 42: STEREO OVERDRIVE
1 Drive 0 — 127
2 EQ Low Frequency 32Hz — 2.0kHz
3 EQ Low Gain -12dB — +12dB
4 LPF Cutoff Freq 1.0kHz — 18.0kHz, thru
5 Output Level 0 — 127
6 Edge 0 — 127
7 EQ Mid Frequency 100Hz — 10.0kHz
8 EQ Mid Gain -12dB — +12dB
9 EQ Mid Width 1 — 12.0
10 Dry/Wet Balance D63>W — D=W — D<W63
43: STEREO AMP SIMULATOR
1 Dry/Wet Balance D63>W — D=W — D<W63
2 Drive 0 — 127
@3 AMP Type Off, Stack, Combo,Tube
4 LPF Cutoff Freq 315Hz — 18.0kHz, thru
5 Edge 0 — 127
6 Output Level 0 — 127
44: DIST + DELAY, 45: OVERDRIVE + DELAY
1 Dist Drive 0 — 127
2 Dist Output Level 0 — 127
3 Dist EQ Low Gain -12dB — +12dB
4 Dist EQ Mid Gain -12dB — +12dB
5 Delay Mix 0 — 127
6 Delay Time L 0.1ms — 1480.0ms
7 Delay Time R 0.1ms — 1480.0ms
8 Dly Feedback Time 0.1ms — 1480.0ms
9 Dly Feedback Level -63 — +63
10 Dry/Wet Balance D63>W — D=W — D<W63
262
Appendix
• A5000/A4000
Degree of distortion
Output level
The frequency band to be distorted
Distortion band cutoff frequency
Type of distortion
Degree of distortion
Output level
Selects the band to be distorted
Distortion band cutoff frequency
Mid, Lo&Hi bandwidth
Type of distortion
Balance of the dry sound and effect sound
Input level at which the gate begins to open
Time until when the gate begins to open
Time until the gate closes
Output level
Degree of distortion
Specifies the type of distortion
Speaker simulation type
High frequency control
Output level
Delay level
Left channel delay time
Right channel delay time
Feedback delay time
Amount of feedback
Balance of the dry sound and effect sound
Degree of distortion
Frequency at which the EQ will boost/cut the low range
Gain with which the EQ will boost/cut the low range
Frequency at which the filter will cut the high range
Output level
Curve of distortion characteristics (127: distortion begins suddenly; 0: distortion begins gradually)
Frequency at which the EQ will boost/cut the mid range
Gain with which the EQ will boost/cut the mid range
Width of the area in which the EQ will boost/cut the mid range
Balance between the dry sound and the effect sound
Balance between the dry sound and the effect sound
Degree of distortion
Select the type of amp to be simulated
Frequency at which the low pass filter will cut the high range
Curve of distortion characteristics (127: distortion begins suddenly; 0: distortion begins gradually)
Output level
Degree of distortion
Frequency at which the EQ will boost/cut the low range
Gain with which the EQ will boost/cut the low range
Frequency at which the filter will cut the high range
Output level
Curve of distortion characteristics (127: distortion begins suddenly; 0: distortion begins gradually)
Frequency at which the EQ will boost/cut the mid range
Gain with which the EQ will boost/cut the mid range
Width of the area in which the EQ will boost/cut the mid range
Balance between the dry sound and the effect sound
Balance between the dry sound and the effect sound
Degree of distortion
Type of amp simulation
Frequency at which the low pass filter will cut the high range
Curve of distortion characteristics (127: distortion begins suddenly; 0: distortion begins gradually)
Output level
Degree of distortion
Output level
Gain with which the EQ will boost/cut the low range
Gain with which the EQ will boost/cut the mid range
Delay level
Left channel delay time
Right channel delay time
Feedback delay time
Amount of feedback
Balance between the dry sound and the effect sound