1. Manuals
  2. Brands
  3. Infineon Manuals
  4. Microcontrollers
  5. TRAVEO T2G Cluster 4M Lite Kit
  6. User manual

Infineon TRAVEO T2G Cluster 4M Lite Kit User Manual

Hide thumbs Also See for TRAVEO T2G Cluster 4M Lite Kit:
Table of Contents

Advertisement

Quick Links

Download this manual
TRAVEO™ T2G Cluster 4M Lite Kit user guide
KIT_ T2G_C-2D-4M_LITE

About this document

Scope and purpose
This user guide enables users to use the KIT_T2G_C-2D-4M_LITE (also known as TRAVEO™ T2G Cluster 4M Lite)
low-cost evaluation kit. It is based on the CYT3DL device from the TRAVEO™ Cluster 2D family of microcontrollers
with on-board EZ-USB™ FX3.
This document describes the features and functions of the TRAVEO™ T2G Cluster 4M lite kit. This document also
provides detailed information on available interfaces and usage of all the hardware interfaces.
Intended audience
This document is intended for software and hardware engineers for evaluating the TRAVEO™ T2G Cluster 2D
family CYT3DL device.
Evaluation board
This board is to be used during the design-in process for software evaluation.
Note:
PCB and auxiliary circuits are NOT optimized for final customer design.
Reference board/Kit
Product(s) embedded on a PCB with a focus on specific applications and defined use cases that may include
software. PCB and auxiliary circuits are optimized for the requirements of the target application.
Note:
Boards do not necessarily meet safety, EMI, quality standards (for example, UL, CE) requirements
User guide
Please read the sections "Important Notice" and "Warnings" at the end of this document
www.infineon.com
002-39200 Rev. **
2023-12-11

Advertisement

Table of Contents
loading

Related Manuals for Infineon TRAVEO T2G Cluster 4M Lite Kit

Summary of Contents for Infineon TRAVEO T2G Cluster 4M Lite Kit

  • Page 1: About This Document

    PCB and auxiliary circuits are optimized for the requirements of the target application. Note: Boards do not necessarily meet safety, EMI, quality standards (for example, UL, CE) requirements User guide Please read the sections “Important Notice” and “Warnings” at the end of this document 002-39200 Rev. ** www.infineon.com 2023-12-11...

  • Page 2: Important Notice

    Boards provided by Infineon Technologies. The design of the Evaluation Boards and Reference Boards has been tested by Infineon Technologies only as described in this document. The design is not qualified in terms of safety requirements, manufacturing and operation over the entire operating temperature range or lifetime.

  • Page 3: Safety Precautions

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Safety precautions Safety precautions Note: Please note the following warnings regarding the hazards associated with development system Table 1 Safety precautions Warning: The evaluation or reference board contains DC bus capacitors which take time to discharge after removal of the main supply.

  • Page 4: Table Of Contents

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Table of contents Table of contents About this document ..............1 Important notice .

  • Page 5: The Board At A Glance

    For streaming TTL RGB packets via the Type-C cable, ensure that it is connected to the USB 3.0 port of the PC. Figure 1 TRAVEO™ T2G Cluster 4M Lite kit content Note: There is no quick start guide (QSG) in the box; visit www.infineon.com/traveoc2d4mlitekit for the QSG and other related documents User guide 002-39200 Rev. ** 2023-12-11...

  • Page 6: Block Diagram

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE The board at a glance Block diagram This section shows the TRAVEO™ T2G Cluster 4M Lite block diagram.  E >/E h^ D < W W^  :d ' zds//   WDK d, W,z ^DWZ &...

  • Page 7: Board Parameters And Technical Data

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE The board at a glance – User LEDs – Push button – Potentiometer • USB Type-C connector – For powering-up the kit – For FX3 output streaming • USB Micro-B connector –...
  • Page 8 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE The board at a glance Table 2 Board functions (continued) Serial Reference designator Function Specification X502 Jumper EZ-USB™ FX3 bootloader jumper S900 User switch User push switch connects to DUT D900 User LED User LED connected to DUT D901...

  • Page 9: System And Functional Description

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE System and functional description System and functional description This section explains how to set up and power up the TRAVEO™ T2G Cluster 4M Lite kit, and how to run the pre- programmed firmware.

  • Page 10: Powering-Up The Lite Kit

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE System and functional description Table 3 Jumper configurations (continued) Jumper Function Position: selection 3.3 V for RPi header 1-2: short (default) X808 No 3.3 V to RPi header 1-2: open TDM RX FSYNC going to RPi header 1-2: short X809 TDM RX FSYNC to TX FSYNC...
  • Page 11 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE System and functional description Figure 3 Connecting the USB Type-C between X500 and USB port of laptop 2.2.2 12-V DC power adapter Change the jumper positions as follows (highlighted with a yellow box in Figure •...
  • Page 12 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE System and functional description Figure 4 shows the connection of the 12-V power adapter and jumper configuration. Figure 4 Connecting 12-V DC power adapter to X100 2.2.3 USB Micro-B Use the same jumper settings as mentioned in the USB Type-C section. After configuring the jumper settings, connect the USB Micro-B cable between the USB Micro-B connector X400 and the USB port of the PC.

  • Page 13: Pre-Programmed Firmware

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE System and functional description Figure 5 Connecting Micro-B cable between X400 and USB port of laptop Note: In this option, the PSoC™ 5LP (KitProg3) is also powered up, which is not possible in other powering options.
  • Page 14 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE System and functional description 2.3.1 Full test log Follow this procedure to see the test logs in the serial terminal window: 1. Open Tera Term (or any serial terminal software) in your PC. Figure 6 Opening serial terminal in PC 2.
  • Page 15 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE System and functional description 3. Next, go to Setup > Serial port > Speed > and select "115200" and press the "New setting" button. Figure 8 Selecting baud-rate of UART in terminal 4.
  • Page 16 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE System and functional description 2.3.2 EZ-USB™ FX3 IRIS pattern Follow this procedure to see the IRIS pattern in the VLC media player (or any media player): 1. First, ensure that jumper X502 (highlighted in the yellow box in Figure 10) is not shorted.
  • Page 17 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE System and functional description 3. Open the VLC media player and go to Media/ Open Capture Device. Figure 12 VLC media player window 4. In the Capture Device tab, enter the following settings: •...
  • Page 18 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE System and functional description 5. Click on the Play button and note the IRIS pattern in the VLC media player window. Figure 14 IRIS pattern coming on screen via FX3 User guide 002-39200 Rev.

  • Page 19: Hardware Blocks

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Hardware blocks This section describes the major hardware blocks of the TRAVEO™ T2G Cluster 4M Lite kit. TRAVEO™ CYT3DL MCU The TRAVEO™ T2G Cluster 4M Lite kit is designed to evaluate the different features and functionality of the TRAVEO™...

  • Page 20: Psoc™ 5Lp (Kitprog3)

    MCU device description. Table 4 MCU device description Reference Manufacturer Part number Package, size U200 Infineon Technologies CYT3DLBBHBES 272- Ball BGA Figure 16 shows the location of the CYT3DL device (MCU) in this kit. Figure 16 CYT3DL device location PSoC™ 5LP (KitProg3) PSoC™...

  • Page 21: Ez-Usb™ Fx3

    KitProg3 location EZ-USB™ FX3 Infineon's EZ-USB™ FX3 is the industry's most versatile USB peripheral controller, which can add a USB 5-Gbps connectivity to any system. The second-generation general programmable interface (GPIF II) of EZ-USB™ FX3 can connect to a processor, an image sensor, an FPGA, or an ASIC. Users can program the GPIF to behave like a FIFO, an asynchronous SRAM, an address/data multiplexed interface, a CompactFlash, or a proprietary interface.

  • Page 22: Power Supply Block

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 18 EZ-USB™ FX3 location Note: Refer to Section 3.7.1. Power supply block This kit supports the on-board PMIC module and LDOs to generate the power supplies to run the TRAVEO™ T2G CYT3DL MCU and other peripherals.
  • Page 23 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks s  /^> /Z d s/K 'W/K h^ D s >K s >K s >K d>^ d>^ d>^ D/W/ /K D/W/ &y  Figure 19 Block diagram of power supply User guide 002-39200 Rev.
  • Page 24 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks The following figure explains the operation of 12 V and 5 V with VIN ORED connection of the TRAVEO™ T2G Cluster 4M Lite Kit. s/E KZ Ws/E KWE s/E KZ Ws/E >K^ Figure 20...

  • Page 25: Program And Debug Interface

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 21 PMIC and LDO location Program and debug interface This kit has an Arm® Standard 20-pin JTAG connector to program and debug the CYT3DL device. Additionally, you can use the on-board debugger KitProg3 to program and debug the CYT3DL device. You can use the GHS Probe directly to program and debug the kit by connecting it to the X302 connector.
  • Page 26 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 22 KitProg3 USB-UART bridge connected to PC Note: Refer to Section 4 for more details. 3.5.2 Arm® standard JTAG interface Figure 23 shows the connection of the GHS probe to the JTAG header X302. Figure 23 Connecting GHS Probe to JTAG header X302 User guide...

  • Page 27: Serial Memory Interface

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 24 shows the connection of the JTAG to the 20-pin Arm® converter from I-jet to the same JTAG header X302. Figure 24 Connecting i-Jet to JTAG header X302 Serial memory interface The Serial Memory Interface (SMIF) is a master that provides a low pin count connection to off-chip SPI devices, such as EEPROM, FRAM, MRAM, or NAND memories, in SDR or DDR mode, and HYPERBUS™...
  • Page 28 SPI. Both interfaces serially transfer transactions reducing the number of interface connection signals. 3.6.2 HYPERRAM™ This kit has S27KL0642 64-Mb HYPERRAM™ self-refresh DRAM (PSRAM). The Infineon 64-Mb HYPERRAM™ device is a high-speed CMOS, self-refresh DRAM, with HYPERBUS™ interface. The DRAM array uses dynamic cells that require periodic refresh.

  • Page 29: Graphics And Video Interface

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Graphics and video interface This kit supports different video-compatible interfaces that can be accessed via specific connectors and supported by compatible components such as displays, camera, and adapter boards. Figure 26 shows the different video and graphic interfaces available in this kit.
  • Page 30 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 27 Connection required to stream FX3 into PC Note: If you want to program the EZ-USB™ FX3, connect the jumper X502 (highlighted in Figure 27) on the board. Ensure that you connect and disconnect the power again in the lite kit after this jumper configuration.
  • Page 31 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks 3.7.2 FPD-Link interface This kit has one FPD-Link interface and it supports graphics output. Connect the FPD-Link display to stream graphics output. Figure 28 FPD-Link connector location on the TRAVEO™ T2G Cluster 4M Lite kit 3.7.3 MIPI-CSI2 interface This kit supports the MIPI-CSI2 interface.

  • Page 32: Hid Interface

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 29 MIPI-CSI2 interface location in TRAVEO™ T2G Cluster 4M Lite kit HID interface This kit supports several Human Interface Device (HID) interfaces to take input or show some indication to the user.
  • Page 33 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 30 User LEDs, push button and potentiometer in TRAVEO™ T2G Cluster 4M Lite kit 3.8.1 User LEDs Since the LEDs used on the board are active high, the corresponding GPIO can be used to control the LED (high - LED on and low - LED off) from the CYT3DL device.

  • Page 34: Crystal Oscillator

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Crystal oscillator This kit supports two external clock sources: External Crystal Oscillator (ECO) and Watch Crystal Oscillator (WCO). Figure 31 shows the location of the crystal oscillators in this kit. Figure 31 ECO and WCO location Note:...

  • Page 35: Expansion Headers

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 32 Reset buttons 3.11 Expansion headers This kit provides a variety of header expansions that are compatible with the most popular interfaces. The kit is designed to be compatible with Arduino™ I/O connection header, mikroBUS™ header, and Shield2Go footprints. There is also one Raspberry Pi compatible header, which can be used with the Audio HAT for I2S Audio.
  • Page 36 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 33 Expansion headers • Raspberry Pi compatible I/O header (highlighted in red) • Arduino-compatible header (highlighted in yellow) • mikroBUS™ compatible header (highlighted in green) • Shield2Go footprints (highlighted in pink) •...
  • Page 37 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Functionality X800.10 SCB6 UART TX X800.11 GPIO2 (P7.2) X800.12 TDM TX SCK0 X800.13 GPIO3 (P7.3) X800.14 X800.15 GPIO4 (P8.0) X800.16 TDM RX SCK0 X800.17 X800.18 TDM TX MCK0 X800.19 SCB7 SPI MOSI X800.20 X800.21...
  • Page 38 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Table 7 Arduino header X803 pin details Functionality X803.1 X803.2 X803.3 X803.4 X803.5 X803.6 XRES# X803.7 VDDIO X803.8 Table 8 Arduino header X805 pin details Functionality X805.1 AN1 (P4.4) X805.2 AN2 (P4.5) X805.3...

  • Page 39: Supported Shields

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Table 11 mikroBUS header 813 pin details Functionality X813.1 GPIO1 (P19.3) X813.2 GPIO2 (P21.3) X813.3 SCB6 UART RX X813.4 SCB6 UART TX X813.5 SCB2 I2C SCL X813.6 SCB2 I2C SDA X813.7 X813.8 3.11.4...
  • Page 40 This kit supports the CY8CKIT-026 CAN and LIN Shield kit, which is an Arduino-compatible shield board used with several Infineon kits such as the CY8CKIT-042 PSoC™ 4 Pioneer Kit/CY8CKIT-044 PSoC™ 4 M-Series Pioneer Kit or the FM4-176L-S6E2GM - Arm® Cortex®-M4 MCU Pioneer Kit. It enables you to evaluate the Controller Area Network (CAN) and Local Interconnect Network (LIN) slave communication capabilities of CYT3DL device.
  • Page 41 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 35 Connecting CAN and LIN shield 3.12.2 WM8960 Audio HAT This kit has a Raspberry Pi compatible I/O header, which can be used to connect this WM8960 Audio HAT for Audio codec.
  • Page 42 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 36 Connecting WM8960 Audio HAT 3.12.3 Ethernet board This kit does not have on-board ethernet PHY but you can use the external ethernet PHY boards by connecting them to the PMOD connector (X801) on the board. The following sections provide details about the boards which are supported with this kit for ethernet.
  • Page 43 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Hardware blocks Figure 37 Connecting external ethernet boards with this kit User guide 002-39200 Rev. ** 2023-12-11...

  • Page 44: Programming And Debugging

    Program CYT3DL device using AutoFlashUtility The AutoFlashUtility is a flexible, cross-platform, integrated application to allow programming Infineon devices. It can perform Program, Erase, Verify, and Read operations on the target device flash. It can target an entire device, a specific region, a sector, and even a byte of a device (contact Technical Support to obtain the tool).

  • Page 45: Program And Debug Cyt3Dl Device Using Iar Embedded Workbench

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Programming and debugging Program and debug CYT3DL device using IAR Embedded Workbench This kit supports the programming and debugging using the third-party software and hardware like IAR-EWARM (embedded workbench for Arm® software and I-Jet debugger) and Green Hills System (Multi IDE software and GHS probe debugger).
  • Page 46 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Programming and debugging 2. Select the revision in the workspace tab as "lite_kit" from the drop-down list under Workspace, as shown in Figure Figure 40 Selecting lite_kit workspace for TRAVEO™ T2G Cluster 4M Lite kit in IAR Note: Ignore the other workspace revisions for this lite_kit.
  • Page 47 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Programming and debugging 4. For checking the debugger option, right-click on the "cm0plus - lite_kit" and select "Options", and then "Debugger". Check what is selected in the driver menu in the Debugger tab. If you are using the I-JET debugger, then select "I-jet"...
  • Page 48 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Programming and debugging 6. Now the rebuild process starts; you can check for errors and warnings in the "Build Log". Figure 44 Checking for errors and warnings in build log in IAR Note: If the build window does not appear on the screen, go to "View >...

  • Page 49: Program And Debug Cyt3Dl Device Using Kitprog3

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Programming and debugging 8. Now click the "Go" icon to start the execution. You can also use the function keys in the Debug window: F5 (Go), F10 (Step Over), F11 (Step into), and Ctrl+D (Download and Debug). Figure 46 Running the code in IAR workspace for TRAVEO™...

  • Page 50: Program Ez-Usb™ Fx3

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Programming and debugging Program EZ-USB™ FX3 Follow the procedure mentioned in this section to program the EZ-USB™ FX3. But before that, download the software required to program EZ-USB™ FX3. To program and use the EZ-USB™ FX3, use the FX3 Software development Kit (FX3 SDK), which comes with tools, drivers, and application example.
  • Page 51 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Programming and debugging Programming FX3 through control center 1. Before programming the FX3, make sure that you connect the jumper X502 on board, to enable FX3 to move to Bootloader mode. Now press the FX3 Reset button (S500) on the board. Figure 49 Shorting the jumper X502 and press reset button in TRAVEO™...
  • Page 52 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Programming and debugging Figure 50 Opening Control Center for programming FX3 4. Select "Cypress FX3 USB Bootloader Device" in the Control Center. Next, go to Program > FX3 , and select "I2C EEPROM".
  • Page 53 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Programming and debugging 5. Now, you will be prompted for the location of the UVC image to flash into FX3. Locate the directory that has the image file which you want to program. After selecting that image in the bottom left of the Control Center, note the status of the flashing.
  • Page 54 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Programming and debugging Attention: If you have connected the X502 jumper on your board, then note the device “Cypress FX3 USB Boot Programmer Device” under the “Universal Serial Bus controllers” tab in the Device Manager, as shown in Figure Figure 54...

  • Page 55: Technical Specifications

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Technical specifications Technical specifications Test points The following table describes the test points available in this kit. Table 13 Available test points available Serial No. Functionality Reference designator FX3 UART_RX TP501 FX3 UART_TX TP502 SMIF0 RWDS...

  • Page 56: Multiplexed Options

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Technical specifications Multiplexed options In this kit, you can use any one functionality of some of the multiplexed pins, depending upon the jumpers or connections you made. Check the connection and jumpers before you decide the functionalities you need. Table 14 Multiplexed options Reference...

  • Page 57: Appendices

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices Appendices Appendix A - Schematics and board design 6.1.1 Board image Figure 56 Top view of the Cluster 4M Lite kit User guide 002-39200 Rev. ** 2023-12-11...
  • Page 58 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices Figure 57 Bottom view of the TRAVEO™ T2G Cluster 4M Lite kit 6.1.2 Schematics The TRAVEO™ T2G C-2D-4M_LITE Kit schematic is documented in this section. • Overview page • Board power page •...
  • Page 59 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices 02_TVII_272_Power.SchDoc 06_SMIF.SchDoc XRES# XRES# SMIF0 01_Power.SchDoc SMIF1 PGOOD 03_TVII_272.SchDoc PGOOD SMIF0 08_Headers.SchDoc SMIF1 05_FX3.SchDoc ETH_HDR ETH_HDR XRES# ARD_HDR ARD_HDR RPI_HDR RPI_HDR MB_HDR MB_HDR 2GO_HDR_2 2GO_HDR_2 2GO_HDR_1 2GO_HDR_1 04_KIT_Prog3.SchDoc 07_LVDS_MIPI.SchDoc XRES# XRES# KITPROG3 KITPROG3...
  • Page 60 Default <Appr.> Size: Document Name Rel. Rev. <Rel.> 01_Power.SchDoc Author: <Author> Date: 26.04.2023 Time: 21:14:39 SVN Revision: 1968 [Locally Modified] © Infineon Technologies AG 2019. All Rights Reserved. Sheet Figure 59 Board power page User guide 002-39200 Rev. ** 2023-12-11...
  • Page 61 Approved Default <Appr.> Size: Document Name Rel. Rev. <Rel.> 02_TVII_272_Power.SchDoc Author: <Author> Date: 26.04.2023 Time: 21:14:40 SVN Revision: 1960 © Infineon Technologies AG 2019. All Rights Reserved. Sheet Figure 60 TVII-272 MCU power page User guide 002-39200 Rev. ** 2023-12-11...
  • Page 62 Default <Appr.> S2*10 Size: Document Name Rel. Rev. <Rel.> 03_TVII_272.SchDoc Author: <Author> Date: 26.04.2023 Time: 21:14:40 SVN Revision: 1965 © Infineon Technologies AG 2019. All Rights Reserved. Sheet Figure 61 TVII-272 MCU schematic page User guide 002-39200 Rev. ** 2023-12-11...
  • Page 63 P15[7:6] (USB D+, D-) Size: Document Name Rel. Rev. 04_KIT_Prog3.SchDoc <Rel.> Author: <Author> Date: 26.04.2023 Time: 21:14:40 SVN Revision: 1968 © Infineon Technologies AG 2019. All Rights Reserved. Sheet Figure 62 KitProg3 schematic page User guide 002-39200 Rev. ** 2023-12-11...
  • Page 64 M24M02-DRMN6TP Size: Document Name Rel. Rev. <Rel.> 05_FX3.SchDoc GNDGNDGND Author: <Author> Date: 26.04.2023 Time: 21:14:41 SVN Revision: 1968 [Locally Modified] © Infineon Technologies AG 2019. All Rights Reserved. Sheet Figure 63 FX3 schematic page User guide 002-39200 Rev. ** 2023-12-11...
  • Page 65 Default <Appr.> Size: Document Name Rel. Rev. 06_SMIF.SchDoc <Rel.> Author: <Author> Date: 26.04.2023 Time: 21:14:41 SVN Revision: 1956 © Infineon Technologies AG 2019. All Rights Reserved. Sheet Figure 64 Serial Memory interface schematic page User guide 002-39200 Rev. ** 2023-12-11...
  • Page 66 Default <Appr.> Size: Document Name Rel. Rev. <Rel.> 07_LVDS_MIPI.SchDoc Author: <Author> Date: 26.04.2023 Time: 21:14:41 SVN Revision: 1956 © Infineon Technologies AG 2019. All Rights Reserved. Sheet Figure 65 LVDS and MIPI schematic page User guide 002-39200 Rev. ** 2023-12-11...
  • Page 67 <Appr.> SSW-108-01-G-S SSW-108-01-G-S Size: Document Name Rel. Rev. <Rel.> 08_Headers.SchDoc Author: <Author> Date: 26.04.2023 Time: 21:14:42 SVN Revision: 1960 © Infineon Technologies AG 2019. All Rights Reserved. Sheet Figure 66 I/O headers schematic page User guide 002-39200 Rev. ** 2023-12-11...
  • Page 68 Size: Document Name Rel. Rev. 09_Reset_Buttons_LED.SchDoc <Rel.> Author: <Author> Date: 26.04.2023 Time: 21:14:42 SVN Revision: 1956 © Infineon Technologies AG 2019. All Rights Reserved. Sheet Figure 67 Reset button, LEDs, and potentiometer schematics page User guide 002-39200 Rev. ** 2023-12-11...
  • Page 69 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices 6.1.3 Assembly drawings Figure 68 Primary assembly drawing of TRAVEO™ T2G Cluster 4M Lite kit User guide 002-39200 Rev. ** 2023-12-11...
  • Page 70 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices Figure 69 Secondary assembly drawing of TRAVEO™ T2G Cluster 4M Lite kit User guide 002-39200 Rev. ** 2023-12-11...

  • Page 71: Bill Of Material

    KIT_T2G_C-2D-4M_LITE Appendices Bill of material The complete bill of material is available in the download section of the Infineon home page. A log-in is required to download this material. Table 15 BOM of the critical parts of the evaluation or reference board (example) S No.
  • Page 72 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices Table 15 BOM of the critical parts of the evaluation or reference board (example) (continued) S No. Reference designator Item name Description R508,R509 Resistor RES, 5.1K OHM, 1%, 1/16W, 0402, SMD R125 Resistor RES, 36K OHM, 1%, 1/16W, 0402, SMD...
  • Page 73 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices Table 15 BOM of the critical parts of the evaluation or reference board (example) (continued) S No. Reference designator Item name Description C111,C128,C134,C140,C146,C421, Ceramic Capacitor CAP, CER, 10UF, 20%, X7R, 16V, 1206 C540,C543 C500,C501 Ceramic Capacitor...
  • Page 74 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices Table 15 BOM of the critical parts of the evaluation or reference board (example) (continued) S No. Reference designator Item name Description D404,D505 SCHOTTKY DIODE DIO, SCHOTTKY DIODE, 20V, 500MA, SOD123 D100, D403 SCHOTTKY DIODE...

  • Page 75: Pin Details

    IC, IFX, SEMPER FLASH, 3.0V, 512 Mbit, 166MHz, FBGA 6x8mm U101, U103, U104 Cypress parts IC, INFINEON, REG, LIN POS, ADJ, 500MA, TSON-10 Pin details This section describes the MCU pin functionalities and also where they are routing in board.
  • Page 76 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices Table 16 MCU pin details (continued) Label Routing to P2[1] BUTTON USER PUSH BUTTON (S900) P2[2] SWO_TDO X302.13 P2[4] SWCLK_TCLK X302.9 P2[5] SWDIO TMS X302.7 P3[0] SWDOE TDI X302.5 P3[1] TRSTN X302.3 P4[0]...
  • Page 77 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices Table 16 MCU pin details (continued) Label Routing to P8[7] GPIO4_2GO_2 S801.13 P9[0] RPI_GPIO8 X800.32 P9[1] RPI_GPIO9 X800.22 P9[2] RPI_GPIO6 X800.31 P9[3] SCB8 SEL1 S800.14 P9[4] SCB8 CLK X802.6, S800.15, S801.15 P9[5] SCB8 MOSI X802.4, S800.16, S801.16...
  • Page 78 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices Table 16 MCU pin details (continued) Label Routing to P14[6] RGB_GREEN3 P14[7] RGB_GREEN2 P15[0] RGB_GREEN1 P15[1] RGB_GREEN0 P15[2] RGB_RED7 P15[3] RGB_RED6 P15[4] RGB_RED5 P15[5] RGB_RED4 P15[6] RGB_RED3 P15[7] RGB_RED2 P16[0] RGB_RED1 P16[1] RGB_RED0...
  • Page 79 TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Appendices Table 16 MCU pin details (continued) Label Routing to P20[7] SPIHB1 DATA7 TP620 P21[0] SPIHB1 CLK TP615 P21[1] SPIHB1_RWDS TP621 P21[2] SPIHB1 SEL0 TP613 P21[3] GPIO2_MB X813.2 User guide 002-39200 Rev. ** 2023-12-11...

  • Page 80: References

    [23] DP83848 ethernet board datasheet [24] LAN8720 ethernet board [25] LAN8720 ethernet board datasheet [26] LAN8720 ethernet board schematic Note: For any questions regarding any peripheral block or code examples, visit the Infineon Developer Community for solutions. User guide 002-39200 Rev. ** 2023-12-11...

  • Page 81: Glossary

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Glossary Glossary Table 1 Abbreviations and definitions Abbreviation Definition Alternating current Analog-to-digital converter Bill of materials Controller area network Capacitor CAN FD Controller area network flexible data-rate Central processing unit Digital-to-analog converter Direct current External crystal oscillator Electrostatic discharge...

  • Page 82: Revision History

    TRAVEO™ T2G Cluster 4M Lite Kit user guide KIT_T2G_C-2D-4M_LITE Revision history Revision history Document Date of release Description of changes version 2023-12-11 Initial release of User guide for Cluster 4M Lite kit Rev-B. User guide 002-39200 Rev. ** 2023-12-11...

  • Page 83: Disclaimer1

    Technologies in a written document signed by 81726 Munich, Germany authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be ©...

This manual is also suitable for:

Kit t2g c-2d-4m lite

Table of Contents