Page 1
32-Bit Microcontroller Application Kit TC2X4 Hardware: APPLICATION KIT TC2X4 V1.0 Hardware Manual User’s Manual V 1.0 2014-10 M i c r o c o n t r o l l e r s...
Page 2
Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life.
Page 3
32-Bit Microcontroller Application Kit TC2X4 Hardware: APPLICATION KIT TC2X4 V1.0 Hardware Manual User’s Manual V 1.0 2014-10 M i c r o c o n t r o l l e r s...
Page 4
Trademarks ® TriCore is a trademark of Infineon Technologies AG. We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document.
This Application Kit Hardware Manual familiarizes you with the TriCore Evaluation Board and guides you through the initial configuration of the Application Kit. For detailed technical information about the TC2X4 (e.g. TC234, TC224) please refer to the User Manual of the device.
Hardware Manual Application Kit Features Application Kit Features Summary of Features – Infineon’s TC2X4 (e.g. TC234, TC224) Controller in TQFP-144 Package – LCD XGA Display 320x240 – SD card slot (mini SD) – High Speed CAN Transceivers – USB to UART bridge –...
Page 15
Application Kit TC2X4 Hardware Manual Application Kit Features – Single Port Gigabit Ethernet PHY PEF7071 (LANTIQ, if Ethernet supported by assembled CPU) – Touch screen controller ADS7843 – 4 general purpose LEDs – Reset switch – Wake switch – Xilinx CPLD XC9572XL User’s Manual...
Power Supply The microcontroller needs 3 different supply voltages. This voltages are generated via Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV (+3,3V and +5V volt for ADC and CAN) and via the microcontroller itself (+1,3V). Applying a stable supply voltage causes the power on reset after a short period. The LED' (+3V3) indicate the status of the 3,3V voltage.
Application Kit TC2X4 Hardware Manual Application Kit Information • Voltage reference 5.0 V +/- 1% for ADC supply, 150 mA current capability (named Volt_Ref) • Two trackers for sensor supply following voltage reference 150 mA current capability each (named Tracker 1 and Tracker 2, not used) •...
Application Kit TC2X4 Hardware Manual Application Kit Information 3.3.1 Write a display register A single write to any register can be done by a 32 bit transfer of SPI. Make sure that the SLSO08 is low during this 32 bit. Bit 31 must be transfered first.
Application Kit TC2X4 Hardware Manual Application Kit Information first transfer has 16 bit: Bit 15 must be 1, this will be indicate a read access. Bit 14 must be 1, this will be indicate an endless access. Bit 13...Bit 7 is the 8 bit register number which will be read Bit 5...Bit 0 are dummy bits to setup the register number.
The transducer is connected to pin P33.0 and needs a 2048Hz frequency. MultiCAN On the board is oneCAN transceiver connected to the MultiCAN on TC2X4 node 0. The transceiver is connected to an IDC10 plug. For the pinout of IDC10 plug see Figure 5-4.
Application Kit Information 3.10 On the board is one LIN transceiver connected to the ASCLIN1 on TC2X4. The transceiver are connected to one IDC10 plug. For the pinout of IDC10 plug see 5-5. You can use a IDC female connector with crimpconnector, flat cable and Figure SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.
Page 26
Application Kit TC2X4 Hardware Manual Application Kit Information If the ACTIV LED is on, then stop the active DAS Server ’UDAS’ and/or remove the USB connection to the PC. User’s Manual V 1.0, 2014-10...
Page 27
Application Kit TC2X4 Hardware Manual Application Kit Information User’s Manual V 1.0, 2014-10...
Application Kit TC2X4 Hardware Manual Signal Description Signal Description For more information about the signals please see the user manuals for TC2X4 and/or the schematics of the board. Table 4-1 Power Signals Short Name Description VCC_IN Supply Input (5,5V...50V(40V)) Input voltage of power supply device...
Application Kit TC2X4 Hardware Manual Connector Pin Assignment Connector Pin Assignment The Application Kit will be shipped with two 40 pin male (plug) connectors on top layer with a standard grid of 2,54mm. IO Connectors X102 X103 VCC_IN +3V3 VCC_IN +3V3 P33.10...
Application Kit TC2X4 Hardware Manual Connector Pin Assignment Power connector pinout + 5 ,5V … + 40 V G N D Figure 5-2 Power connector pinout USB connector pinout Figure 5-3 USB connector Pinout CAN connector pinout Figure 5-4 CAN connector pinout (IDC10) User’s Manual...