Operation - Husqvarna DXR 95 Operator's Manual

• Replace worn components. There is an increased
risk of mechanical failure if the product is used with
damaged or worn components.
• Replace worn or missing signs and decals.
• Do not use a product that is defective. Do the safety
checks, maintenance and the servicing as given in
this manual. All other maintenance work must be
done by an approved service agent.
• Make sure you have necessary training to do
maintenance.
• Use lifting equipment to lift heavy product parts
and to keep them in a stable position during
maintenance. Lock product parts mechanically
before maintenance to prevent injury from moving
parts.
• If you go away from the product, do a lockout-tagout
procedure.
Introduction
WARNING:
product, you must read and understand the
safety chapter.
To do before you operate the product
1. Read the operator's manual carefully and make sure
that you understand the instructions.
2. Put on necessary personal protective equipment.
Personal protective equipment on page 25 .
Refer to
3. Use a remote control harness to keep your body in
correct position and prevent injury.
4. Make sure that no persons are in the work area.
5. Do daily maintenance. Refer to
schedule on page 86 .
6. Make sure that the product is not damaged.
7. Install the tool on the product. Make sure that the
tool is correctly and safely installed. Refer to
install and remove the tools on the product (DXR
95) on page 41 or To install and remove the tools
on the product (DXR 145, DXR 275, DXR 305, DXR
315) on page 42 .
8. Make sure that the safety devices on the product are
not defective.
9. Put the product in the work area. Make sure that the
transportation of the product to and in the work area
is done safely and correctly. Refer to
on page 139 .
10. Make sure that the power cord and extension cable
are in good condition and not damaged.
11. Connect the product to a power source. Refer to
connect the product to a power source on page 39 .
1401 - 005 - 11.01.2024

Operation

Before you operate the
Maintenance
To
Transportation
To
• Only approved servicing personnel are permitted to
do maintenance in the electrical system and the
hydraulic system.
• Do the maintenance to make sure that the product
operates correctly. Refer to
on page 86 .
• Do not do the troubleshooting of hydraulic leakage
with your hands. Do the troubleshooting visually.
• Collect hydraulic oil if you spill. Collect items that
have contamination. Dispose all items that have
contamination in accordance with the applicable
environmental regulations. Hydraulic oil is harmful
for the environment and can cause groundwater and
soil contamination.
12. Make sure that tools, such as screwdrivers or other
objects that are not used, are removed from the
product.
13. Make sure that the temperature of the hydraulic oil is
not less then 10°C/50°F. Refer to
become warm on page 39 .
To connect the product to a power
source
WARNING:
product through an RCD with personal
protection. The RCD must trip at a ground
fault of 30 mA.
1. Make sure that the voltage is compatible with the
product and that the correct fuses are used. Refer
Guide values for connection to a mains socket on
to
page 150 .
2. Connect the power plug of the product to the
extension cable.
3. Connect the extension cable to a mains outlet.
To let the product become warm
CAUTION:
pressure if the temperature of the hydraulic
oil is less than 10°C/50°F. You get maximum
pump pressure when you operate the
outriggers or the arm system to maximum
extension.
1. Start the product. Refer to
95) on page 70 and To start the product (DXR 145)
on page 71 and To start the product (DXR 275,
DXR 305, DXR 315) on page 72 .
2. Extend the outriggers. Refer to
outriggers on page 83 .
Maintenance schedule
To let the product
Always connect the
Do not use maximum pump
To start the product (DXR
To operate the
39