ABB RELION SMU615 Technical Manual page 40

Basic functions
Fault indication Fault
code
Internal Fault File 7
system error
Internal Fault Test 8
Internal Fault SW 10
watchdog error
Internal Fault SO- 43
relay(s),X100
Internal Fault SO- 44
relay(s),X110
Internal Fault SO- 45
relay(s),X120
Internal Fault SO- 46
relay(s),X130
Internal Fault PO- 53
relay(s),X100
Internal Fault PO- 54
relay(s),X110
Internal Fault PO- 55
relay(s),X120
Internal Fault PO- 56
relay(s),X130
Internal Fault Light 59
sensor error
Table continues on the next page
40
Additional Fast self-
information recovery
attempt
(# of
attempts)
Start up error or Yes (2)
runtime error: file
system error
Internal fault test No
activated manual-
ly by the user.
Start up error: No
Watchdog reset
has occurred too
many times with-
in an hour. Note!
This is different
indication than
Warning code 10:
Watchdog reset
Runtime error: Yes (2)
Faulty Signal Out-
put relay(s) in card
located in slot
X100.
Runtime error: Yes (2)
Faulty Signal Out-
put relay(s) in
card located in
slot X110.Runtime
error:
Runtime error: Yes (2)
Faulty Signal Out-
put relay(s) in card
located in slot
X120.
Runtime error: Yes (2)
Faulty Signal Out-
put relay(s) in card
located in slot
X130.
Runtime error: Yes (2)
Faulty Power Out-
put relay(s) in card
located in slot
X100.
Runtime error: Yes (2)
Faulty Power Out-
put relay(s) in card
located in slot
X110.
Runtime error: Yes (2)
Faulty Power Out-
put relay(s) in card
located in slot
X120.
Runtime error: Yes (2)
Faulty Power Out-
put relay(s) in card
located in slot
X130.
Runtime error: Yes (2)
Faulty ARC light
sensor input(s).
Slow 10 Immediate Action in permanent fault state
min self- permanen
recovery (# t IRF-
of mode
attempts)
Yes (3) No Restart the relay. If recovered by re-
starting, continue relay normal op-
eration. If not recover by restart-
ing, replace the relay, most probably
hardware failure in CPU module.
No - Just check the "Internal fault test"
-setting parameter position, if relay
is in test mode
No Yes Restart the relay. If recovered by re-
starting, continue relay normal op-
eration. If not recover by restarting,
replace the relay.
Yes (3) No Check wirings. Restart the relay. If
recovered by restarting, continue
relay normal operation. If not recov-
er by restarting, exchange the hard-
ware module in slot X100.
Yes (3) No Check wirings. Restart the relay. If
recovered by restarting, continue
relay normal operation. If not recov-
er by restarting, exchange the hard-
ware module in slot X110.
Yes (3) No Check wirings. Restart the relay. If
recovered by restarting, continue
relay normal operation. If not recov-
er by restarting, exchange the hard-
ware module in slot X120.
Yes (3) No Check wirings. Restart the relay. If
recovered by restarting, continue
relay normal operation. If not recov-
er by restarting, exchange the hard-
ware module in slot X130.
Yes (3) No Check wirings. Restart the relay. If
recovered by restarting, continue
relay normal operation. If not recov-
er by restarting, exchange the hard-
ware module in slot X100.
Yes (3) No Check wirings. Restart the relay. If
recovered by restarting, continue
relay normal operation. If not recov-
er by restarting, exchange the hard-
ware module in slot X110.
Yes (3) No Check wirings. Restart the relay. If
recovered by restarting, continue
relay normal operation. If not recov-
er by restarting, exchange the hard-
ware module in slot X120.
Yes (3) No Check wirings. Restart the relay. If
recovered by restarting, continue
relay normal operation. If not recov-
er by restarting, exchange the hard-
ware module in slot X130.
Yes (3) No Check wirings. Restart the relay. If
recovered by restarting, continue
1MRS758407 C
SMU615
Technical Manual