Port Input/Output Control - Epson Arm S1C31 Series Technical Manual

Initial settings when using a port as a general-purpose input port
(only for the ports with GPIO function)
When using the Pxy port pin as a general-purpose input pin, perform the following software initial settings:
1. Write 0 to the PPORTPxINTCTL.PxIEy bit. *
2. When using the chattering filter, configure the PPORT operating clock (see "PPORT Operating Clock") and
set the PPORTPxCHATEN.PxCHATENy bit to 1. *
When the chattering filter is not used, set the PPORTPxCHATEN.PxCHATENy bit to 0 (supply of the
PPORT operating clock is not required).
3. Configure the following PPORTPxRCTL register bits when pulling up/down the port using the internal
pull-up or down resistor:
- PPORTPxRCTL.PxPDPUy bit
- Set the PPORTPxRCTL.PxRENy bit to 1.
Set the PPORTPxRCTL.PxRENy bit to 0 if the internal pull-up/down resistors are not used.
4. Set the PPORTPxMODSEL.PxSELy bit to 0.
5. Configure the following bits when using the port input interrupt: *
- Write 1 to the PPORTPxINTF.PxIFy bit.
- PPORTPxINTCTL.PxEDGEy bit
- Set the PPORTPxINTCTL.PxIEy bit to 1.
6. Set the following PPORTPxIOEN register bits:
- Set the PPORTPxIOEN.PxOENy bit to 0.
- Set the PPORTPxIOEN.PxIENy bit to 1.
* Steps 1 and 5 are required for the ports with an interrupt function. Step 2 is required for the ports with a chat-
tering filter function.
Table 7.4.1.1 lists the port status according to the combination of data input/output control and pull-up/down
control.
PPORTPxIOEN. PPORTPxIOEN.
PxIENy bit PxOENy bit
0 0
0 0
0 0
1 0
1 0
1 0
0 1
0 1
0 1
1 1
1 1
*1: Initial status. Current does not flow if the pin is placed into floating status.
*2: Use of the pull-up or pull-down function is recommended, as undesired current will flow if the port input is set to floating status.
Note: If the PPORTPxMODSEL.PxSELy bit for the port without a GPIO function is set to 0, the port
goes into initial status (refer to "Initial Settings"). The GPIO control bits are configured to a read-
only bit always read out as 0.

7.4.2 Port Input/Output Control

Peripheral I/O function control
The port for which a peripheral I/O function is selected is controlled by the peripheral circuit. For more infor-
mation, refer to the respective peripheral circuit chapter.
S1C31D41 TECHNICAL MANUAL
(Rev. 1.1)
Table 7.4.1.1 GPIO Port Control List
PPORTPxRCTL. PPORTPxRCTL.
PxRENy bit PxPDPUy bit
0
×
1 0
1 1
0
×
1 0
1 1
0
×
1 0
1 1
1 0
1 1
Seiko Epson Corporation
(Disable interrupt)
(Select pull-up or pull-down resistor)
(Enable pull-up/down)
(Enable GPIO function)
(Clear interrupt flag)
(Select interrupt edge (input rising edge/falling edge))
(Enable interrupt)
(Disable output)
(Enable input)
Input Output
Disabled
Disabled
Disabled
Enabled Disabled
Enabled Disabled
Enabled Disabled
Disabled Enabled
Disabled Enabled
Disabled Enabled
Enabled Enabled
Enabled Enabled
7 I/O PORTS (PPORT)
Pull-up/pull-down
condition
Off (Hi-Z) *1
Pulled down
Pulled up
Off (Hi-Z) *2
Pulled down
Pulled up
Off
Off
Off
Off
Off
7-5