Table of Contents
Advertisement
Chapter 6.
Fix Long prop. assy (item 4) on both ends of BTM section Assy-5 (item 1) with the
help of a Hex bolt (item 22) and lock washer (item 23). This is shown in detail C of
fig. 6.3. Now fix cable support assy (item 2) to the long prop. assy (item 4) using Hex
bolt (item 26), lock washer (item 27) Hex nut (item 28), lock washer (item 23) Fig.
6.2 (detail b). Now this support assy (item 3) is to be provided support at both ends.
For this fix leg (item 12) and Angle brace (item 13) with the help of Hex bolt (item
22) lock washer (item 23) and Hex nut (item 24). The brace angle is to be fixed to
the floor also with the help of expansion bolt (M6x65). So mark the drilling points.
Make the holes and fix the expansion bolts after drilling of holes. For this support
assy may have to be removed temporarily for drilling of holes. Refer Fig. 6.2 (detail
a). Short prop. assy (item 5) is to be fixed with BTM section assy - 5 (item 1) using
Hex bolt (item 22) lock washer (item 23) and Hex nut (item 24) as shown in Fig.
6.4 (detail e). Top ends of these three short prop. assy (item 5) are provided a
support by angle section-5 (item 8). This is fixed with long & short prop. assy using
Hex bolt (item 22) lock washer (item 23) and Hex nut (item 24) as shown in fig. 6.4.
Angle long (item 10) is to be fixed with cable support assy (item 2) and support assy
(item 3) using Hex bolt (item 26), lock washer (item 27) and Hex nut (item 28) as
shown in Fig. 6.5.
Cross member assy (item 6) passing through long prop. assy (item 4) is fixed onto
Angle long (item 10) using cheese head screw (item 29) lock washer (item 32) and
Hex nut (item 33).
Similarly cross member assy (item 6) passing through short prop. assy (item 5) is
fixed onto Angle short (item 9) using cheese head screw (item 29) lock washer
(item 32) and Hex nut (item 33). Refer fig. 6.6. Strip-5 (item 11) is to be joined with
cross member assy (item 6) using counter sunk screw. Similarly Horizontal Angle -
5 (item 14) is joined onto cross member assy (item 6) using counter sunk screw.
Refer fig. 6.7 (detail j).
Bent conduit -1 (item 17) and Bent conduit - 2 (item 18) are to be fixed onto conduit
- 4 (item 16) using hex bolt (item 25) and lock washer (item 27). Then this assembly
is joined onto support (item 3) using Hex bolt (item 26) and lock washer (item 27),
Refer Fig. 6.8. Top angle section - 5 (item 21) and clamp (item 20) are to be fixed
onto long prop assy (item 4) using Hex bolt (item 26), lock washer (item 27) and Hex
nut (item 28) as shown in Fig. 6.9.
Backmount frame - 11 is fixed onto Angle short (item 9) and Angle Long (item 10)
using cheese head screw, lock washer and Hex nut. Backmount frame - 9 is fixed
onto horizontal angle - 5 (item 14) with the help of cheese head screw, lock washer
and Hex nut.
For expanding MDF capacity, another similar structure for 5 verticals is to be
added using Fish plate - 1 (item 9) and Fish Plate-2 (item 17).
66
C-DOT DSS MAX-XL
Advertisement
Table of Contents
