JLG 600SC Service And Maintenance Manual page 88

SECTION 3 - CHASSIS & TURNTABLE
SPN
523757
523758
523759
523760
523766
523767
523768
523769
523776
523777
523778
523779
523788
523788
523788
523793
523794
523803
523858
523867
523889
523891
523895
523896
523897
523898
523899
523900
523906
523906
523906
523906
523910
523910
523910
523910
523910
523910
523911
523911
523911
523911
3-42
Table 3-1. Deutz Trouble Codes (TD2.9 L4 Engine)
FMI
14 special pattern for special cases No detail information
14 special pattern for special cases No detail information
14 special pattern for special cases No detail information
14 special pattern for special cases No detail information
9 Timeout Error of CAN-Receive-Frame Active TSC1AE
9 Timeout Error of CAN-Receive-Frame Passive TSC1AE
9 Timeout Error of CAN-Receive-Frame Active TSC1AR
9 Timeout Error of CAN-Receive-Frame Passive TSC1AR
9 Timeout Error of CAN-Receive-Frame TSC1TE - active
9 Passive Timeout Error of CAN-Receive-Frame TSC1TE; Set point
9 Timeout Error of CAN-Receive-Frame TSC1TR
9 Passive Timeout Error of CAN-Receive-Frame TSC1TR
12 Timeout Error of CAN-Transmit-Frame TrbCH; Status Waste gate
0 Waste gate plausibility error off CAN transmit message.
0 Timeout Error of CAN-Receive-Frame ComTrbChActr; Wastegate
9 Timeout Error of CAN-Receive-Frame UAA10; AGS sensor service message
9 Timeout Error of CAN-Receive-Frame UAA11; AGS sensor data
9 Timeout error of CAN Receive Message RxEngPres; Status Burner Air Pump
12 Timeout Error of CAN-Transmit-Frame UAA11
12 Timeout Error of CAN-Transmit-Frame UAA1 on CAN 2. Control burner air pump;
3 Over temperature of device driver of pressure control valve No detail information
14 When AirHt_ctDefSRCLoOn_mp is less than AirHt_ctMaxDef_C.
DFC to SRC Low error when heater is On No detail information
13 Check of missing injector adjustment value programming (IMA) injector 1 (in firing order).
13 Check of missing injector adjustment value programming (IMA) injector 2 (in firing order).
13 Check of missing injector adjustment value programming (IMA) injector 3 (in firing order).
13 Check of missing injector adjustment value programming (IMA) injector 4 (in firing order).
13 Check of missing injector adjustment value programming (IMA) injector 5 (in firing order).
13 Check of missing injector adjustment value programming (IMA) injector 6 (in firing order).
5 Electrical fuel pre - supply pump; open load
12 Electrical fuel pre - supply pump. ECU powerstage over temperature.
3 Electrical fuel pre - supply pump; short circuit to battery
4 Electrical fuel pre - supply pump. Short circuit to ground.
14 Air pump doesn't achieve air mass flow setpoint Burner Control - burner air pump
9 Burner Control; Air Pump - CAN Lost Air Pump; CAN communication lost
7 Air pump; CAN communication interrupted no purge function available
12 Air Pump; internal error
0 Air Pump; operating voltage error
6 Burner Control Air Pump; over current Air pump electrically overloaded
0 Burner dosing valve (DV2); over current at the end of the injection phase
12 Burner dosing valve (DV2); power stage over temperature
3 Burner dosing valve (DV2); short circuit to battery
4 Burner dosing valve (DV2); short circuit to ground
Error Identification
3121776