Husqvarna FE 350 2016 Repair Manual page 6

TABLE OF CONTENTS
15.3
15.4
15.5
15.6
15. 7
15.8
16 BRAKE SYSTEM ........................................... 148
16.1
16.2
16.3
16.4
16.5
16.6
16.7
16.8
16.9
16.10
16.11
16.12
16.13
16.14
16.15
17 LIGHTING SYSTEM, INSTRUMENTS ........... 166
17.1
17.2
17.3
17.4
17.5
17.6
17.7
18 ENGINE ......................................................... 171
18.1
18.2
18.3
18.3.1
18.3.2
18.3.3
18.3.4
18.3.5
18.3.6
18.3.7
18.3.8
4
Checking the starter relay ................. 143
Removing the battery ........................ 143
Installing the battery ......................... 144
Recharging the battery ..................... 145
Checking the charging voltage ......... 146
Checking the open-circuit current.. .. 146
Checking the front brake linings ....... 148
Changing the front brake linings ....... 148
Checking the free travel of the
hand brake lever ............................... 151
Adjusting the basic position of the
hand brake lever (FE 350 US) ........... 151
Adjusting free travel of hand brake
lever (FE EU/AU, FE 350 S US) ......... 152
Checking the front brake fluid
level ................................................... 152
Adding front brake fluid .................... 153
Changing the front brake fluid .......... 154
Checking the rear brake linings ........ 157
Changing the rear brake linings ........ 158
Checking the free travel of foot
brake lever . . .. . .. . .. . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Adjusting the basic position of the
foot brake lever ................................. 161
Checking the rear brake fluid level ... 161
Adding rear brake fluid ..................... 162
Changing the rear brake fluid ........... 163
Adjusting the combination
instrument......................................... 166
Adjusting the kilometers or miles ...... 167
Adjusting the clock ........................... 167
Setting the wheel circumference ...... 168
Adjusting the service display ............ 168
Checking the headlight setting ......... 169
Adjusting the headlight range ........... 169
Removing the engine ........................ 171
Installing the engine .......................... 175
Engine disassembly .......................... 181
Preparations ................................. 181
Removing the clutch push rod ..... 181
Removing the spacer ................... 181
Draining the engine oil. ................. 181
Removing the oil filter ................... 182
Removing the spark plug ............. 182
Removing the valve cover ............ 183
Removing the alternator cover ..... 183
18.3.9 Removing the torque limiter ......... 184
18.3.10 Positioning the engine at
ignition top dead center ............... 184
18.3.11 Removing the timing chain
tensioner ....................................... 184
18.3.12 Removing the camshaft ............... 185
18.3.13 Removing the cylinder head ......... 185
18.3.14 Removing the piston .................... 186
Removing the starter drive ........... 186
18.3.15
18.3.16 Removing the suction pump ........ 188
18.3.17 Removing the water pump
wheel ............................................ 189
18.3.18 Removing the clutch cover ........... 189
18.3.19 Removing the clutch discs ........... 189
18.3.20 Removing the clutch basket ......... 190
18.3.21 Removing the shift shaft ............... 191
18.3.22 Removing the shift drum
locating unit.. ................................ 191
18.3.23 Removing the locking lever .......... 192
18.3.24
Removing the force pump ............ 192
18.3.25 Removing the primary gear .......... 193
18.3.26 Removing the timing chain ........... 193
18.3.27 Removing the spacer ................... 193
18.3.28 Removing the left section of the
engine case .................................. 194
18.3.29 Removing the shift rails ................ 194
18.3.30 Removing the shift drum .............. 195
18.3.31 Removing the shift forks .............. 195
18.3.32 Removing the transmission
shafts ............................................ 195
18.3.33 Removing the crankshaft ............. 196
18.4 Working on individual parts .............. 196
18.4.1 Work on the right section of the
engine case .................................. 196
18.4.2 Working on the left section of
the engine case ............................ 198
18.4.3 Work on the clutch cover ............. 199
18.4.4 Checking the oil pressure
regulator valve .............................. 201
18.4.5 Checking the lubrication
system .......................................... 202
18.4.6 Removing the crankshaft
bearing inner race ......................... 202
18.4.7 Installing the crankshaft bearing
inner race ...................................... 203
18.4.8 Changing the connecting rod,
conrod bearing and crank pin ...... 203
18.4.9 Checking the crankshaft run-out
at the bearing pin ......................... 205
18.4.10 Measuring the crankshaft end
play ............................................... 205
18.4.11 Removing the drive wheel of the
balancer shaft ............................... 206