Husqvarna FE 350 2022 Owner's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Motorcycle
  5. FE 350 2022
  6. Owner's manual

Husqvarna FE 350 2022 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNER'S MANUAL 2022
FE 350
Art. no. 3402540en

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna FE 350 2022

Summary of Contents for Husqvarna FE 350 2022

  • Page 1 OWNER'S MANUAL 2022 FE 350 Art. no. 3402540en...
  • Page 3 DEAR HUSQVARNA MOTORCYCLES CUSTOMER Congratulations on your decision to purchase a Husqvarna motorcycle. You are now the owner of a state-of- DEAR HUSQVARNA MOTORCYCLES CUSTOMER the-art sports vehicle which, with appropriate care, will bring you pleasure for a long time to come.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS TABLE OF CONTENTS 6.14 Opening fuel tank filler cap ....21 MEANS OF REPRESENTATION......6 6.15 Closing the fuel tank filler cap..... 22 Symbols used ........6 6.16 Cold start button......... 22 Formats used ........6 6.17 Idle speed adjusting screw ....
  • Page 5 TABLE OF CONTENTS Transporting........40 12.9 Removing the lower triple clamp ..57 Refueling ..........40 12.10 Installing the lower triple clamp ..58 12.11 Checking the steering head bearing SERVICE SCHEDULE........42 play ............. 60 10.1 Additional information......42 12.12 Adjusting the steering head bearing 10.2 Required work........
  • Page 6 TABLE OF CONTENTS 13.2 Checking the brake discs ....89 TUNING THE ENGINE ........123 13.3 Checking the front brake fluid level ..90 17.1 Checking the play in the throttle 13.4 Adding the front brake fluid .... 90 cable ..........123 13.5 Checking the front brake linings ..
  • Page 7 TABLE OF CONTENTS INDEX OF SPECIAL TERMS ......157 LIST OF ABBREVIATIONS ......158 LIST OF SYMBOLS ........159 29.1 Yellow and orange symbols....159 29.2 Green and blue symbols....159 INDEX ..............160...

  • Page 8: Means Of Representation

    1 MEANS OF REPRESENTATION Symbols used The meaning of specific symbols is described below. Indicates an expected reaction (e.g. of a work step or a function). Indicates an unexpected reaction (e.g. of a work step or a function). All work marked with this symbol requires specialist knowledge and technical understand- ing.

  • Page 9: Safety Advice 2

    SAFETY ADVICE 2 Use definition – intended use (EU) This vehicle has been designed and built to withstand the normal stresses and strains of racing. This vehi- cle complies with the currently valid regulations and categories of the top international motorsports organi- zations.

  • Page 10: Degrees Of Risk And Symbols

    2 SAFETY ADVICE Degrees of risk and symbols Danger Identifies a danger that will immediately and invariably lead to fatal or serious permanent injury if the appropriate measures are not taken. Warning Identifies a danger that is likely to lead to fatal or serious injury if the appropriate measures are not taken.

  • Page 11: Protective Clothing

    – Always wear protective clothing that is in good condition and meets the legal regulations. In the interest of your own safety, Husqvarna Motorcycles recommends that you only operate the vehicle while wearing protective clothing. Work rules Unless specified otherwise, the ignition must be turned off during all work (models with ignition lock, models with remote key) or the engine must be at a standstill (models without ignition lock or remote key).

  • Page 12: Environment

    Because motorcycles are not subject to the EU regulations governing the disposal of used vehicles, there are no legal regulations that pertain to the disposal of an end-of-life motorcycle. Your authorized Husqvarna Motor- cycles dealer will be glad to advise you.

  • Page 13: Important Notes 3

    IMPORTANT NOTES 3 Manufacturer warranty, implied warranty The work prescribed in the service schedule must only be carried out in an authorized Husqvarna Motorcy- cles workshop and confirmed in the Husqvarna Motorcycles Dealer.net, as otherwise all warranty claims will be void. Damage or secondary damage caused by tampering with and/or conversions on the vehicle are not covered by the manufacturer warranty.

  • Page 14: Customer Service

    3 IMPORTANT NOTES Customer service Your authorized Husqvarna Motorcycles dealer will be happy to answer any questions you may have regarding your vehicle and Husqvarna Motorcycles. A list of authorized Husqvarna Motorcycles dealers can be found on the Husqvarna Motorcycles website.

  • Page 15: View Of Vehicle 4

    VIEW OF VEHICLE 4 View of vehicle, front left (example) F03489-10 Hand brake lever ( p. 17) Clutch lever ( p. 17) Fuel tank filler cap Air filter box cover Side stand ( p. 24) Engine number ( p. 15) Shift lever ( p.

  • Page 16: View Of Vehicle, Rear Right (Example)

    4 VIEW OF VEHICLE View of vehicle, rear right (example) F03490-10 Fork compression adjuster Stop button ( p. 17) p. 18) (EU) Horn button ( Light switch ( p. 18) (EU) Turn signal switch ( p. 19) (EU) Start button ( p.

  • Page 17: Serial Numbers 5

    SERIAL NUMBERS 5 Vehicle identification number The vehicle identification number is stamped on the right side of the steering head. 401945-10 Type label (EU) The Europe type label is fixed to the front of the steering head. The Canada type label is fixed to the front of the chest tube.

  • Page 18: Fork Part Number

    5 SERIAL NUMBERS Fork part number The fork part number is stamped on the inner side of the fork stub. 401947-10 Shock absorber article number Shock absorber article number is stamped on the top of the shock absorber above the adjusting ring towards the engine side. H02222-10...

  • Page 19: Controls 6

    CONTROLS 6 Clutch lever Clutch lever is fitted on the handlebar on the left. The clutch is activated hydraulically and adjusts itself automati- cally. F03491-10 Hand brake lever The hand brake lever is fitted on the right side of the handle- bar.

  • Page 20: Horn Button (Eu)

    6 CONTROLS (US) The stop button is fitted on the left side of the handlebar. Possible states is in the basic position – In this position, • The stop button the ignition circuit is closed and the engine can be started. pressed –...

  • Page 21: Turn Signal Switch (Eu)

    CONTROLS 6 Turn signal switch (EU) Turn signal switch is fitted on the left side of the handlebar. Possible states Turn signal off – The turn signal switch is in the cen- tral position. Left turn signal, on – The turn signal switch is turned to the left.

  • Page 22: Combination Switch

    – The OBD has detected an error in the vehicle elec- tronics. Come safely to a halt, and contact an autho- rized Husqvarna Motorcycles workshop. The fuel level warning lamp lights up yellow – The fuel level has reached the reserve mark.

  • Page 23: Overview Of Indicator Lights (Us)

    – The OBD has detected an error in the vehicle elec- tronics. Come safely to a halt, and contact an autho- rized Husqvarna Motorcycles workshop. The fuel level warning lamp lights up yellow – The fuel level has reached the reserve mark.

  • Page 24: Closing The Fuel Tank Filler Cap

    6 CONTROLS 6.15 Closing the fuel tank filler cap – Mount fuel tank filler cap and turn it clockwise until the release button engages. Info Route fuel tank breather hose without kinks. F03500-10 6.16 Cold start button The cold start button is fitted to the bottom of the throttle valve body.

  • Page 25: Idle Speed Adjusting Screw

    CONTROLS 6 6.17 Idle speed adjusting screw The idle setting of the throttle valve body substantially influences the vehicle’s starting behavior, a stable idle speed, and the vehi- cle’s response when the throttle is opened. An engine with a correctly set idle speed is easier to start than an engine with the idle speed set incorrectly.

  • Page 26: Foot Brake Lever

    6 CONTROLS 6.19 Foot brake lever Foot brake lever is located in front of the right footrest. The rear brake is engaged with the foot brake lever. 401956-10 6.20 Side stand The side stand is attached to the left side of the vehicle. 401943-10 The side stand is used for parking the motorcycle.

  • Page 27: Locking The Steering (Eu)

    CONTROLS 6 6.22 Locking the steering (EU) Note Danger of damage The parked vehicle can roll away or fall over. – Park the vehicle on a firm and level surface. – Park the vehicle. – Turn handlebar as far as possible to the right. –...

  • Page 28: Combination Instrument

    Battery voltage of the combination instrument – Bat- tery voltage of the combination instrument is too low. Change combination instrument battery. Service – A service is due. Contact an authorized Husqvarna Motorcycles workshop. 401901-01 Setting the combination instrument Condition The motorcycle is stationary.

  • Page 29: Adjusting The Kilometers Or Miles

    COMBINATION INSTRUMENT 7 – Wait for 5 seconds. Combination instrument changes to the next menu item. symbol flashes. – Press one of the buttons to select the 24 h display or 12 h display for the clock. 401911-01 – Wait for 5 seconds. Combination instrument changes to the next menu item.

  • Page 30: Setting The Clock

    7 COMBINATION INSTRUMENT – Press and hold both buttons for 3 - 5 seconds. The Setup menu is displayed. The UNIT display flashes. – Press one of the buttons to select UNIT for the speed in kilo- meters KM/H or miles M/H. 401909-01 Setting the clock Condition...

  • Page 31: Speed, Time, And Dst Distance 1

    COMBINATION INSTRUMENT 7 Switching off the service interval display – Press and hold the left button. off appears in the display. 401914-01 Speed, time, and DST distance 1 – Press one of the buttons until DST appears on the combina- tion instrument.

  • Page 32: Avg Average Speed, Art Operating Hours, And Odo Total Distance Covered

    7 COMBINATION INSTRUMENT Press the left DST2 can be preset to a value between 0.0 button for 3 – and 39999.9 by pressing the buttons. 5 seconds. Press the Next display mode right button briefly. Press the DST2 is reset to 0.0. right button for 3 –...

  • Page 33: Preparing For Use 8

    When using your motorcycle, remember that others may feel disturbed by excessive noise. – Make sure that the pre-sale inspection work has been carried out by an authorized Husqvarna Motorcycles workshop. You will receive a delivery certificate when the vehicle is handed over.

  • Page 34: Running-In The Engine

    8 PREPARING FOR USE – Adjust basic position of the hand brake lever. ( p. 89) – Adjust the basic position of the foot brake lever. p. 95) – Adjust the basic position of the shift lever. p. 128) – Get used to the handling characteristics of the motorcycle on a suitable surface before undertaking more challenging trips.

  • Page 35: Starting Power Of Lithium-Ion Batteries At Low Temperatures

    Riding at low temperatures and in snow. ( p. 35) Preparing the vehicle for riding on dry sand – Mount the air filter dust cover. Air filter dust cover (79006920000) Info Read the fitting instructions for Husqvarna Motorcy- cles accessories. 102136-01...

  • Page 36: Preparing The Vehicle For Riding On Wet Sand

    8 PREPARING FOR USE – Mount the air filter sand cover. Air filter sand cover (79006922000) Info Read the fitting instructions for Husqvarna Motorcy- cles accessories. 102138-01 – Clean the chain. – Mount the steel sprocket. – Grease the chain.

  • Page 37: Preparing Vehicle For High Temperatures Or Slow Riding

    Straighten bent radiator fins carefully. – Check the coolant level. ( p. 120) Preparing the vehicle for low temperatures or snow – Mount the air filter rain cover. Air filter rain cover (79006921000) Info Read the fitting instructions for Husqvarna Motorcy- cles accessories. 102137-01...

  • Page 38: Riding Instructions

    9 RIDING INSTRUCTIONS Checks and maintenance measures when preparing for use Info Before every trip, check the condition of the vehicle and ensure that it is safe to operate. The vehicle must be in perfect technical condition when it is being operated. –...

  • Page 39: Activating Traction Control

    RIDING INSTRUCTIONS 9 – Take the motorcycle off side stand and secure the side stand with rubber strap – Shift the transmission into neutral. (EU) – Turn the emergency OFF switch to the position Condition Ambient temperature: < 20 °C (< 68 °F) –...

  • Page 40: Starting Off

    Danger of accidents A spongy pressure point on the front or rear brake reduces braking efficiency. – Check the brake system and do not continue riding until the problem is eliminated. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

  • Page 41: Stopping, Parking

    RIDING INSTRUCTIONS 9 Warning Danger of accidents Moisture and dirt impair the brake system. – Brake carefully several times to dry out and remove dirt from the brake linings and the brake discs. – On sandy, wet, or slippery surfaces, use the rear brake. –...

  • Page 42: Transporting

    In some countries and regions, the available fuel quality and cleanliness may not be sufficient. This will result in problems with the fuel system. – Refuel only with clean fuel that meets the specified standards. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)
  • Page 43 RIDING INSTRUCTIONS 9 Note Environmental hazard Improper handling of fuel is a danger to the environment. – Do not allow fuel to enter the groundwater, the soil, or the sewage system. – Switch off engine. – Open fuel tank filler cap. ( p.

  • Page 44: 10 Service Schedule

    Different service intervals may apply in your country, depending on the local operating conditions. Individual service intervals and scopes may change in the course of technical developments. The most up-to- date service schedule can always be found on Husqvarna Motorcycles Dealer.net. Your authorized Husqvarna Motorcycles dealer will be glad to advise you.

  • Page 45: Recommended Work

    ● Final check: Check the vehicle is roadworthy and take a test ride. ○ ● ● ● ● Read out the fault memory after the test ride using the Husqvarna Motorcycles diag- nostics tool. ○ ● ● ● ● Make a service entry in Husqvarna Motorcycles Dealer.net.
  • Page 46 10 SERVICE SCHEDULE every 48 months every 12 months Every 135 operating hours Every 70 operating hours when used for motorsports After 20 operating hours After 10 operating hours ● ● Perform engine service including removing and installing the engine. (Change the spark plug and spark plug connector.

  • Page 47: Tuning The Chassis 11

    The shock absorber is filled with highly compressed nitrogen. – Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Info The effect of the low-speed compression adjuster can be seen in slow to normal compression of the...

  • Page 48: Adjusting The High-Speed Compression Damping Of The Shock Absorber

    The shock absorber is filled with highly compressed nitrogen. – Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Info The effect of the high speed compression adjuster can be seen in the fast compression of the shock absorber.

  • Page 49: Adjusting The Rebound Damping Of The Shock Absorber

    Risk of injury Parts of the shock absorber will move around if the shock absorber is detached incor- rectly. The shock absorber is filled with highly compressed nitrogen. – Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) – Turn adjusting screw clockwise up to the last perceptible click.

  • Page 50: Checking The Static Sag Of The Shock Absorber

    11 TUNING THE CHASSIS Finishing work – Remove the motorcycle from the lift stand. ( p. 54) 11.7 Checking the static sag of the shock absorber – Measure dimension of rear wheel unloaded. ( p. 47) – Hold the motorcycle upright with aid of an assistant. –...

  • Page 51: Adjusting The Spring Preload Of The Shock Absorber

    The shock absorber is filled with highly compressed nitrogen. – Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Info Before changing the spring preload, make a note of the present setting, e.g., by measuring the spring length.

  • Page 52: Adjusting The Riding Sag

    11 TUNING THE CHASSIS 11.10 Adjusting the riding sag Preparatory work – Raise the motorcycle with a lift stand. ( p. 54) – Remove the shock absorber. p. 63) – After removing the shock absorber, clean it thoroughly. Main work –...

  • Page 53: Adjusting The Compression Damping Of The Fork

    TUNING THE CHASSIS 11 11.12 Adjusting the compression damping of the fork Info The hydraulic compression damping determines the fork suspension behavior. – Turn white adjuster clockwise as far as it will go. Info Adjuster is located at the upper end of the left fork leg.

  • Page 54: Adjusting The Spring Preload Of The Fork

    11 TUNING THE CHASSIS Info Turn clockwise to increase the damping; turn counterclockwise to reduce damping when the shock absorber rebounds. 11.14 Adjusting the spring preload of the fork Preparatory work – Raise the motorcycle with a lift stand. ( p.

  • Page 55: Adjusting The Handlebar Position

    TUNING THE CHASSIS 11 11.16 Adjusting the handlebar position Warning Danger of accidents A repaired handlebar poses a safety risk. If the handlebar is bent or straightened, the material becomes fatigued. The handlebar may break as a result. – Change the handlebar if the handlebar is damaged or bent. –...

  • Page 56: 12 Service Work On The Chassis

    12 SERVICE WORK ON THE CHASSIS 12.1 Raising the motorcycle with a lift stand Note Danger of damage The parked vehicle can roll away or fall over. – Park the vehicle on a firm and level surface. – Raise the motorcycle at the frame underneath the engine. Lift stand (81329955100) Neither wheel is in contact with the ground.

  • Page 57: Cleaning The Dust Boots Of The Fork Legs

    SERVICE WORK ON THE CHASSIS 12 12.4 Cleaning the dust boots of the fork legs Preparatory work – Raise the motorcycle with a lift stand. ( p. 54) – Remove the fork protector. ( p. 55) Main work – Push dust boots of both fork legs downward.

  • Page 58: Installing The Fork Protector

    12 SERVICE WORK ON THE CHASSIS 12.6 Installing the fork protector – Position the fork protector on the left fork leg. Mount and tighten screws Guideline Remaining screws, 10 Nm (7.4 lbf ft) chassis – Position the brake line, wiring harness, and clamp. Mount and tighten screws –...

  • Page 59: Installing The Fork Legs

    SERVICE WORK ON THE CHASSIS 12 12.8 Installing the fork legs Main work – Position the fork legs. Bleeder screws are positioned toward the front. Info The compression damping is located in left fork leg COMP (white adjuster). The rebound damping is located in right fork leg REB (red adjuster).

  • Page 60: Installing The Lower Triple Clamp

    12 SERVICE WORK ON THE CHASSIS Main work – Remove screw – Remove screw – Open cable holder in front of the left radiator and detach the clutch line. – Take off the upper triple clamp with the handlebar and set aside.
  • Page 61 SERVICE WORK ON THE CHASSIS 12 – Position the upper triple clamp with the handlebar. – Mount screw , but do not tighten yet. – Mount the clutch line with cable holder S03552-11 – Position the fork legs. Bleeder screws are positioned toward the front.

  • Page 62: Checking The Steering Head Bearing Play

    Danger of accidents Incorrect steering head bearing play impairs the handling characteristic and damages components. – Correct incorrect steering head bearing play immediately. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Info If the vehicle is operated for a lengthy period with play in the steering head bearing, the bearings and the bearing seats in the frame can become damaged over time.

  • Page 63: Adjusting The Steering Head Bearing Play

    SERVICE WORK ON THE CHASSIS 12 Main work – Move the handlebar to the straight-ahead position. Move the fork legs to and fro in the direction of travel. Play should not be detectable on the steering head bear- ing. » If there is detectable play: –...

  • Page 64: Lubricating The Steering Head Bearing

    12 SERVICE WORK ON THE CHASSIS 12.13 Lubricating the steering head bearing – Remove the lower triple clamp. p. 57) – Install the lower triple clamp. p. 58) Info The steering head bearing is cleaned and lubricated in the course of removal and installation of the lower triple clamp.

  • Page 65: Installing Front Fender

    SERVICE WORK ON THE CHASSIS 12 12.15 Installing front fender Main work – Position front fender. Mount and tighten screws Guideline Remaining screws, 10 Nm (7.4 lbf ft) chassis – Mount and tighten screws Guideline Remaining screws, 10 Nm (7.4 lbf ft) chassis H03691-10 Finishing work...
  • Page 66 12 SERVICE WORK ON THE CHASSIS – Press angle lever toward the rear. – Press linkage lever downward. H03694-10 (EU) – Disconnect the plug-in connector of the brake light switch. F03465-10 – Remove screws – Pull off foot brake cylinder from the push rod. F03466-10 –...

  • Page 67: Installing The Shock Absorber

    SERVICE WORK ON THE CHASSIS 12 – Hold the shock absorber and remove screw – Remove the shock absorber carefully at the bottom. F03469-10 12.17 Installing the shock absorber Main work – Carefully position the shock absorber into the vehicle from the bottom.

  • Page 68: Removing The Seat

    12 SERVICE WORK ON THE CHASSIS – Position the foot brake cylinder. Push rod engages in the foot brake cylinder. The dust boot is correctly positioned. – Mount and tighten screws Guideline Remaining screws, 10 Nm (7.4 lbf ft) chassis F03472-10 –...

  • Page 69: Mounting The Seat

    SERVICE WORK ON THE CHASSIS 12 Main work – Remove screw with the bushing. – Pull seat back and lift it off. S03559-10 12.19 Mounting the seat Main work – Mount the front of the seat on the collar bushing of the fuel tank and the rear in the bracket.

  • Page 70: Removing The Air Filter Box Cover

    12 SERVICE WORK ON THE CHASSIS 12.20 Removing the air filter box cover – Pull off the air filter box cover sideways in areas and take off toward the rear. F02311-10 12.21 Installing the air filter box cover – Attach catch of the air filter box in area and push for- ward.

  • Page 71: Installing The Air Filter

    SERVICE WORK ON THE CHASSIS 12 Main work – Detach retaining tab . Remove air filter with air filter sup- port. – Remove air filter from air filter support. F02313-10 12.23 Installing the air filter Main work – Mount the clean air filter on the air filter support. –...

  • Page 72: Removing The Right Side Cover

    12 SERVICE WORK ON THE CHASSIS Main work – Wash the air filter thoroughly in special cleaning liquid and allow it to dry properly. Air filter cleaner ( p. 154) Info Only press the air filter to dry it, never wring it out. –...

  • Page 73: Installing The Right Side Cover

    SERVICE WORK ON THE CHASSIS 12 12.26 Installing the right side cover Main work – Attach side cover with the holding lugs from below and push upward. – Engage the side cover in areas F03474-10 Finishing work – Mount the seat. ( p.

  • Page 74: Installing The Main Silencer

    12 SERVICE WORK ON THE CHASSIS 12.28 Installing the main silencer Main work (EU) – Position the catalytic converter in the main silencer. S02101-10 – Position the main silencer. – Mount screws , but do not tighten yet. – Attach spring Spring hook (50305017000C1) –...
  • Page 75 SERVICE WORK ON THE CHASSIS 12 S03542-10 Main work – Remove all screws, take off silencer cap with O-ring Info Do not remove the glass fiber yarn filling. Caution Danger to health Soot particles irritate the eyes and mucuous membranes. – Wear suitable breathing and eye protection when cleaning the main silencer and carbon screen.

  • Page 76: Changing The Glass Fiber Yarn Filling In The Main Silencer

    12 SERVICE WORK ON THE CHASSIS 12.30 Changing the glass fiber yarn filling in the main silencer Warning Danger of burns The exhaust system gets very hot when the vehicle is driven. – Allow the exhaust system to cool down before performing any work on the vehicle. Info Over time, the fibers of the glass fiber yarn filling escape and the damper "burns"...

  • Page 77: Removing The Fuel Tank

    SERVICE WORK ON THE CHASSIS 12 (US) – Remove all the screws on the main silencer. – Take off silencer cap with the filter and O-ring – Remove glass fiber yarn filling from main silencer – Clean the parts that need to be reinstalled and check for damage.
  • Page 78 12 SERVICE WORK ON THE CHASSIS – Remove the seat. ( p. 66) – Remove the right side cover. ( p. 70) Main work – Unplug connector of the fuel pump. – Clean quick release coupling thoroughly with compressed air. Info Under no circumstances should dirt enter into the fuel line.

  • Page 79: Installing The Fuel Tank

    SERVICE WORK ON THE CHASSIS 12 12.32 Installing the fuel tank Danger Fire hazard Fuel is highly flammable. The fuel in the fuel tank expands when warm and can escape if overfilled. – Do not fuel the vehicle in the vicinity of open flames or lit cigarettes. –...

  • Page 80: Checking For Chain Dirt Accumulation

    12 SERVICE WORK ON THE CHASSIS (EU) – Position the horn with the horn bracket. – Mount and tighten screws Guideline Remaining screws, 10 Nm (7.4 lbf ft) chassis H03705-11 – Plug in connector for the fuel pump. – Remove the wash cap set. –...

  • Page 81: Cleaning The Chain

    SERVICE WORK ON THE CHASSIS 12 12.34 Cleaning the chain Warning Danger of accidents Lubricants on the tires reduces the road grip. – Remove lubricants from the tires using a suitable cleaning agent. Warning Danger of accidents Oil or grease on the brake discs reduces the braking effect. –...

  • Page 82: Adjusting The Chain Tension

    12 SERVICE WORK ON THE CHASSIS Main work – Pull the chain at the end of the chain sliding piece upward to measure chain tension Info Lower chain section must be taut. When the chain guard is mounted, it must be possi- ble to pull up the chain at least to the point where it makes contact with chain guard Chain wear is not always even, so you should repeat...

  • Page 83: Checking The Chain, Rear Sprocket, Engine Sprocket, And Chain Guide

    SERVICE WORK ON THE CHASSIS 12 Main work – Loosen nut – Loosen nuts – Adjust the chain tension by turning adjusting screws left and right. Guideline Chain tension 55 … 58 mm (2.17 … 2.28 in) Turn adjusting screws on the left and right so that the markings on the left and right chain adjusters are in the same position relative to reference marks...
  • Page 84 12 SERVICE WORK ON THE CHASSIS – Pull on the top section of the chain with the specified weight Guideline Weight of chain wear mea- 10 … 15 kg (22 … 33 lb.) surement – Measure distance of 18 chain rollers in the lower chain section.
  • Page 85 SERVICE WORK ON THE CHASSIS 12 – Check chain sliding piece for wear. » If the lower edge of the chain pins is in line with or below the chain sliding piece: – Change the chain sliding piece. – Check that the chain sliding piece is firmly seated. »...

  • Page 86: Checking The Frame

    If the link fork exhibits damage, cracking, or deformation: – Change the link fork. Info Always replace a damaged link fork. Repair of the link fork is not authorized by Husqvarna Motorcycles. 401520-01 12.40 Checking the throttle cable routing Preparatory work –...

  • Page 87: Checking The Rubber Grip

    SERVICE WORK ON THE CHASSIS 12 Finishing work – Install the fuel tank. p. 77) – Install the right side cover. ( p. 71) – Mount the seat. ( p. 67) – Install the air filter box cover. ( p. 68) 12.41 Checking the rubber grip –...

  • Page 88: Checking/Correcting The Fluid Level Of Hydraulic Clutch

    12 SERVICE WORK ON THE CHASSIS Info Turn the adjusting screw clockwise to increase the distance between the clutch lever and the handlebar. Turn the adjusting screw counterclockwise to decrease the distance between the clutch lever and the handlebar. The range of adjustment is limited. Turn the adjusting screw by hand only, and do not apply any force.

  • Page 89: Changing The Hydraulic Clutch Fluid

    SERVICE WORK ON THE CHASSIS 12 Info Immediately clean up any brake fluid that has over- flowed or spilled with water. 12.44 Changing the hydraulic clutch fluid Warning Skin irritation Brake fluid causes skin irritation. – Keep brake fluid out of the reach of children. –...

  • Page 90: Removing The Engine Guard

    12 SERVICE WORK ON THE CHASSIS – Now inject fluid into the system until it escapes from the openings of the master cylinder without bubbles. – Occasionally extract the fluid from the master cylinder reser- voir to prevent overflowing. – Remove the bleeding syringe.

  • Page 91: Brake System 13

    Warning Danger of accidents Worn-out brake discs reduce the braking effect. – Make sure that worn-out brake discs are replaced immediately. (Your authorized Husqvarna Motor- cycles workshop will be glad to help.) – Check the front and rear brake disc thickness at multiple...

  • Page 92: Checking The Front Brake Fluid Level

    – Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) – Move the brake fluid reservoir mounted on the handlebar to a horizontal position.

  • Page 93: Checking The Front Brake Linings

    Checking the front brake linings Warning Danger of accidents Worn-out brake linings reduce the braking effect. – Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcy- cles workshop will be glad to help.) – Check the brake linings for minimum thickness ≥...

  • Page 94: Changing The Brake Linings Of The Front Brake

    Danger of accidents Brake linings which have not been approved alter the braking efficiency. Not all brake linings are tested and approved for Husqvarna motorcycles. The structure and friction coefficient of the brake linings, and thus their brake power, may vary greatly from that of original brake linings.
  • Page 95 BRAKE SYSTEM 13 – Move the brake fluid reservoir mounted on the handlebar to a horizontal position. – Remove screws – Take off cover with membrane F03508-10 – Manually press the brake caliper toward the brake disc to push back the brake pistons. Ensure that brake fluid does not flow out of the brake fluid reservoir, extract some if neces- sary.

  • Page 96: Checking The Free Travel Of Foot Brake Lever

    13 BRAKE SYSTEM – Add brake fluid up to level Guideline 5 mm (0.2 in) Level (brake fluid level below reservoir rim) Brake fluid DOT 4 / DOT 5.1 ( p. 152) – Position cover with membrane – Mount and tighten screws Info Use water to immediately clean up any brake fluid that has overflowed or spilled.

  • Page 97: Adjusting The Basic Position Of The Foot Brake Lever

    Warning Danger of accidents Old brake fluid reduces the braking effect. – Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

  • Page 98: Adding Rear Brake Fluid

    Danger of accidents Old brake fluid reduces the braking effect. – Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Note Environmental hazard Hazardous substances cause environmental damage.

  • Page 99: Checking The Rear Brake Linings

    Checking the rear brake linings Warning Danger of accidents Worn-out brake linings reduce the braking effect. – Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcy- cles workshop will be glad to help.) – Check the brake linings for minimum thickness ≥...
  • Page 100 Danger of accidents Brake linings which have not been approved alter the braking efficiency. Not all brake linings are tested and approved for Husqvarna motorcycles. The structure and friction coefficient of the brake linings, and thus their brake power, may vary greatly from that of original brake linings.
  • Page 101 BRAKE SYSTEM 13 – Remove the brake linings. – Clean the brake caliper and the brake caliper bracket. – Check that spring plate in the brake caliper and brake pad sliding plate in the brake caliper bracket are fitted correctly. –...

  • Page 102: 14 Wheels, Tires

    14 WHEELS, TIRES 14.1 Removing the front wheel Preparatory work – Raise the motorcycle with a lift stand. ( p. 54) Main work – Manually press the brake caliper toward the brake disc to push back the brake pistons. Info Make sure that you do not press the brake caliper against the spokes when pushing back the brake pis- tons.

  • Page 103: Installing The Front Wheel

    WHEELS, TIRES 14 14.2 Installing the front wheel Warning Danger of accidents Oil or grease on the brake discs reduces the braking effect. – Always keep the brake discs free of oil and grease. – Clean the brake discs with brake cleaner when necessary. –...

  • Page 104: Installing The Rear Wheel

    14 WHEELS, TIRES Main work – Manually press the brake caliper toward the brake disc to push back the brake piston. Info Make sure that you do not press the brake caliper against the spokes when pushing back the brake pis- ton.
  • Page 105 WHEELS, TIRES 14 Main work – Check the wheel bearing for damage and wear. » If the wheel bearing is damaged or worn: – Change the rear wheel bearing. – Clean and grease shaft seal rings and contact surfaces of the spacers. Long-life grease ( p.

  • Page 106: Checking The Tire Condition

    Checking the tire condition Info Only mount tires approved and/or recommended by Husqvarna Motorcycles. Other tires could have a negative effect on handling characteristics. The type, condition, and pressure of the tires all have a major impact on the handling characteristic of the motorcycle.

  • Page 107: Checking Spoke Tension

    Other spokes will become looser as a result. – Check spoke tension regularly, and in particular on a new vehicle. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) –...

  • Page 108: 15 Electrical System

    15 ELECTRICAL SYSTEM 15.1 Removing the 12-V battery Note Environmental hazard 12 V batteries contain environmentally hazardous materials. – Do not dispose of 12 V batteries as household waste. – Dispose of 12 V batteries at a collection point for used batteries. Note Environmental hazard Hazardous substances cause environmental damage.

  • Page 109: Installing The 12-V Battery

    ELECTRICAL SYSTEM 15 – Detach wiring harness , disconnect relays and hang them to the side. S03579-10 – Remove screw and unhook the holding bracket. – Lift out the 12-V battery. S03582-10 15.2 Installing the 12-V battery Main work – Insert the 12-V battery into the battery compartment with the terminals facing forward and secure with holding bracket 12-V battery (HJTZ5S-FP-C) (...
  • Page 110 15 ELECTRICAL SYSTEM – Place the relays on the holding bracket and attach wiring harness S03579-11 – Attach starter relay and fuse box to the holding bracket. S03578-11 – Connect positive cable to the 12-V battery. Guideline Screw, battery termi- 2.5 Nm (1.84 lbf ft) Info Contact disk...

  • Page 111: Charging The 12-V Battery

    ELECTRICAL SYSTEM 15 15.3 Charging the 12-V battery Warning Risk of injury 12 V batteries contain harmful substances. – Keep 12 V batteries out of the reach of children. – Keep sparks and open flames away from 12 V batteries. – Only charge 12 V batteries in well-ventilated rooms.

  • Page 112: Changing Main Fuse

    12-V battery with this battery charger. The charg- ing time may be longer at low temperatures. This battery charger is only suitable for lithium iron phosphate batteries. Read the accompanying instruc- tions for Husqvarna Motorcycles accessories. Info Never remove cover –...

  • Page 113: Changing The Fuses Of Individual Electrical Power Consumers

    ELECTRICAL SYSTEM 15 Main work – Pull starter relay from the holder. S03588-10 – Take off protection caps – Remove faulty main fuse Info A faulty fuse has a burned-out fuse wire A spare fuse is located in the starter relay. –...
  • Page 114 15 ELECTRICAL SYSTEM Guideline (EU) Fuse 1 – 10 A – EFI control unit, lambda sensor, combi- nation instrument, combination switch (optional), elec- tronic fuel injection, diagnostics connector, fuel vapor retention system, fuse 4 Fuse 2 ‑ 10 A ‑ high beam, low beam, position light, tail light, license plate lamp Fuse 3 - 10 A - radiator fan, horn, brake light, turn sig- Fuse 4 - 5 A - fuel pump...

  • Page 115: Removing The Headlight Mask With The Headlight

    ELECTRICAL SYSTEM 15 15.6 Removing the headlight mask with the headlight – Loosen rubber straps . Slide the headlight mask up and swing it forward. H03749-10 – Remove screw – Detach the brake line and wiring harness from the headlight mask.
  • Page 116 15 ELECTRICAL SYSTEM (US) – Join plug-in connector H03751-11 – Position the brake line and the wiring harness in the cable guide. – Mount and tighten screw – Position the headlight mask. The holding lugs engage in the fender. H03752-10 –...

  • Page 117: Changing The Headlight Bulb

    ELECTRICAL SYSTEM 15 15.8 Changing the headlight bulb Note Damage to reflector Grease on the reflector reduces the light intensity. Grease on the bulb will evaporate due to the heat and be deposited on the reflector. – Clean and degrease the bulbs before mounting. –...

  • Page 118: Checking The Headlight Setting

    15 ELECTRICAL SYSTEM Main work – Remove the screw on the rear of the turn signal housing. – Carefully remove turn signal glass – Lightly squeeze orange cap in the area of the holding lugs and take it off. – Press the turn signal bulb lightly into the socket, turn it coun- terclockwise by about 30°, and pull it out of the socket.

  • Page 119: Adjust The Headlight Range

    ELECTRICAL SYSTEM 15 15.11 Adjust the headlight range. Preparatory work – Check the headlight setting. ( p. 116) Main work – Loosen screw – Adjust the headlight range by pivoting the headlight. Guideline The boundary between light and dark must be exactly on the lower mark for a motorcycle with rider (instructions on how to apply the mark: Checking the headlight setting).

  • Page 120: Diagnostics Connector

    15 ELECTRICAL SYSTEM Finishing work – Install the headlight mask with the headlight. ( p. 113) – Check the headlight setting. ( p. 116) – Set the combination instrument. ( p. 26) 15.13 Diagnostics connector Diagnostics connector is located under the seat. H00933-12...

  • Page 121: Cooling System 16

    COOLING SYSTEM 16 16.1 Cooling system Water pump in the engine ensures forced circulation of the coolant. The pressure resulting from the warming of the cooling system is regulated by a valve in radiator cap . This ensures that operat- ing the vehicle at the specified coolant temperature will not result in a risk of malfunctions.

  • Page 122: Checking The Coolant Level

    16 COOLING SYSTEM Coolant ( p. 152) – Mount the radiator cap. 16.3 Checking the coolant level Warning Danger of scalding During motorcycle operation, the coolant gets very hot and is under pressure. – Do not open the radiator, the radiator hoses or other cooling system components if the engine or the cooling system are at operating temperature.

  • Page 123: Refilling With Coolant

    COOLING SYSTEM 16 Warning Danger of poisoning Coolant is toxic and a health hazard. – Keep coolant out of the reach of children. – Do not allow coolant to come into contact with the skin, the eyes and clothing. – Consult a doctor immediately if coolant is swallowed. –...

  • Page 124: Changing The Coolant

    16 COOLING SYSTEM – Check the coolant level. ( p. 120) 16.6 Changing the coolant Warning Danger of scalding During motorcycle operation, the coolant gets very hot and is under pressure. – Do not open the radiator, the radiator hoses or other cooling system components if the engine or the cooling system are at operating temperature.

  • Page 125: Tuning The Engine 17

    TUNING THE ENGINE 17 17.1 Checking the play in the throttle cable – Check the throttle grip for smooth operation. – Move the handlebar to the straight-ahead position. Turn the throttle grip back and forth slightly and determine the play in throttle cable Play in throttle cable 3 …...

  • Page 126: Adjusting The Characteristic Map Of The Throttle Response

    17 TUNING THE ENGINE Main work – Move the handlebar to the straight-ahead position. – Push back sleeve – Loosen nut – Turn adjusting screw in as far as possible. – Loosen nut – Push cold start button all the way to the stop. –...
  • Page 127 TUNING THE ENGINE 17 – Remove guide plate from handle tube – Position the required guide plate on the grip tube. Guideline The label OUTSIDE must be visible. Marking must be positioned at marking Grey guide plate (79002014000) Alternative 1 Black guide plate (79002014100) Info The gray guide plate opens the throttle valve more...

  • Page 128: Changing The Mapping

    Adjusting the idle speed Warning Danger of accidents The engine may go out spontaneously if the idle speed is set too low. – Set the idle speed to the specified value. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

  • Page 129: Programming The Throttle Valve Position

    TUNING THE ENGINE 17 – Run the engine until warm. The cold start button is deactivated – The cold start but- ton is in its basic position. ( p. 22) Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and death.

  • Page 130: Checking The Basic Position Of The Shift Lever

    17 TUNING THE ENGINE 17.7 Checking the basic position of the shift lever Info When driving, the shift lever must not touch the rider's boot when in the basic position. When the shift lever keeps touching the boot, the transmission will be subject to an excessive load. –...

  • Page 131: Service Work On The Engine 18

    SERVICE WORK ON THE ENGINE 18 18.1 Changing the fuel screen Danger Fire hazard Fuel is highly flammable. The fuel in the fuel tank expands when warm and can escape if overfilled. – Do not fuel the vehicle in the vicinity of open flames or lit cigarettes. –...

  • Page 132: Checking The Engine Oil Level

    18 SERVICE WORK ON THE ENGINE Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and death. – Always make sure there is sufficient ventilation when running the engine. – Use effective exhaust extraction when starting or running the engine in an enclosed space.
  • Page 133 SERVICE WORK ON THE ENGINE 18 Info Drain the engine oil with the engine at operating temperature. Preparatory work – Park the motorcycle on a level surface. – Remove the engine guard. ( p. 88) Main work – Position an appropriate container under the engine. –...
  • Page 134 18 SERVICE WORK ON THE ENGINE – Remove screws . Remove the oil filter cover with the O- ring. V01397-10 – Pull oil filter out of the oil filter housing. Lock ring plier (51012011000) – Allow the engine oil to drain completely. –...

  • Page 135: Adding Engine Oil

    Engine oil (SAE 10W/50) ( p. 152) Info In order to achieve optimal engine oil performance, it is not advisable to mix different engine oils. Husqvarna Motorcycles recommends changing the engine oil. – Mount and tighten the filler plug together with the O-ring. Danger Danger of poisoning Exhaust gases are toxic and...

  • Page 136: 19 Cleaning, Care

    19 CLEANING, CARE 19.1 Cleaning the motorcycle Note Material damage Components become damaged or destroyed if a pressure cleaner is used incorrectly. The high pressure forces water into the electrical components, connectors, throttle cables, and bearings, etc. Pressure which is too high causes malfunctions and destroys components. –...

  • Page 137: Checks And Maintenance Steps For Winter Operation

    CLEANING, CARE 19 – Treat bare metal (except for brake discs and the exhaust sys- tem) with a corrosion inhibitor. Preserving materials for paints, metal and rubber p. 154) – Treat all plastic parts and powder-coated parts with a mild cleaning and care product.

  • Page 138: 20 Storage

    – Store the vehicle in a dry location that is not subject to large fluctuations in temperature. Info Husqvarna Motorcycles recommends raising the motorcycle. – Raise the motorcycle with a lift stand. ( p. 54) –...

  • Page 139: Preparing For Use After Storage

    STORAGE 20 Info Avoid running the engine for a short time only. Since the engine cannot warm up properly, the water vapor produced during combustion condenses and causes valves and the exhaust system to rust. 20.2 Preparing for use after storage –...

  • Page 140: 21 Troubleshooting

    Check the electrical system. – Error in the electronic fuel Read out the fault memory using the injection Husqvarna Motorcycles diagnostics tool. – Engine does not speed up Error in the electronic fuel Read out the fault memory using the...
  • Page 141 – Read out the fault memory using the Husqvarna Motorcycles diagnostics tool. – High oil consumption Engine vent hose bent Route the vent hose without bends or replace it if necessary.
  • Page 142 21 TROUBLESHOOTING Faults Possible cause Action – The high beam, low beam, tail Fuse 2 blown Change the fuses of individual electri- light, position light, and license cal power consumers. ( p. 111) plate lamp are not working – The horn, brake light, turn sig- Fuse 3 blown Change the fuses of individual electri- nal, and radiator fan are not...

  • Page 143: Blink Code 22

    BLINK CODE 22 Info The blink codes are only displayed by the derestricted version of the vehicle. Blink code for malfunc- tion indicator lamp 02a Malfunction indicator lamp flashes 2x per second Error level condition Throttle valve position programming necessary Blink code for malfunc- tion indicator lamp 02 Malfunction indicator lamp flashes 2x short...
  • Page 144 22 BLINK CODE Blink code for malfunc- tion indicator lamp 33 Malfunction indicator lamp flashes 3x long, 3x short Error level condition Injector cylinder 1 - circuit fault Blink code for malfunc- tion indicator lamp 37 Malfunction indicator lamp flashes 3x long, 7x short Error level condition Ignition coil 1, cylinder 1 - circuit fault Blink code for malfunc-...

  • Page 145: Technical Data 23

    TECHNICAL DATA 23 23.1 Engine Design 1-cylinder 4-stroke engine, water-cooled Displacement 349.7 cm³ (21.34 cu in) Stroke 57.5 mm (2.264 in) Bore 88 mm (3.46 in) Compression ratio 13.5:1 Idle speed 1,950 … 2,050 rpm Control DOHC, four valves controlled via cam lever, drive via timing chain Valve diameter, intake 36.3 mm (1.429 in)

  • Page 146: Engine Tightening Torques

    23 TECHNICAL DATA 23.2 Engine tightening torques Nozzle, crank chamber ventilation 2 Nm (1.5 lbf ft) ® Loctite 243™ Oil nozzle for clutch lubrication 2 Nm (1.5 lbf ft) ® Loctite 243™ Oil nozzle for conrod bearing 2 Nm (1.5 lbf ft) ®...
  • Page 147 TECHNICAL DATA 23 Screw, oil filter cover 10 Nm (7.4 lbf ft) Screw, shift drum locating 10 Nm (7.4 lbf ft) ® Loctite 243™ Screw, shift lever 14 Nm (10.3 lbf ft) ® Loctite 243™ Screw, starter motor 10 Nm (7.4 lbf ft) Screw, starter motor - intermedi- 10 Nm (7.4 lbf ft) ®...

  • Page 148: Capacities

    23 TECHNICAL DATA Nut, inner clutch hub M18x1.5 100 Nm (73.8 lbf ft) ® Loctite 243™ Nut, primary gear wheel M18LHx1.5 120 Nm (88.5 lbf ft) ® Loctite 243™ Screw plug, oil screen M20x1.5 15 Nm (11.1 lbf ft) Plug, timing chain tensioner M24x1.5 40 Nm (29.5 lbf ft) Screw, alternator cover...

  • Page 149: Electrical System

    80/100 - 21 M/C 51M TT 110/100 - 18 M/C 64M TT Dunlop GEOMAX AT 81 F Dunlop GEOMAX AT81 The tires specified represent one of the possible series production tires. Additional information is available in the Service section under: www.husqvarna-motorcycles.com...

  • Page 150: Fork

    23 TECHNICAL DATA 23.7 Fork Fork article number 0266C169V401000 Fork WPXPLOR 5548 Compression damping Comfort 18 clicks Standard 15 clicks Sport 12 clicks Rebound damping Comfort 18 clicks Standard 15 clicks Sport 12 clicks Spring preload – preload adjuster Comfort Standard Sport Spring length with preload spacer(s)

  • Page 151: Chassis Tightening Torques

    TECHNICAL DATA 23 Spring length 260 mm (10.24 in) Gas pressure 10 bar (145 psi) Static sag 37 mm (1.46 in) Riding sag 110 mm (4.33 in) Fitted length 477 mm (18.78 in) Shock absorber oil Shock absorber fluid (SAE 2.5) (50180751S1) ( p.
  • Page 152 23 TECHNICAL DATA Nut, starter motor 4 Nm (3 lbf ft) Nut, throttle cable on throttle 3 Nm (2.2 lbf ft) valve body Remaining nuts, chassis 10 Nm (7.4 lbf ft) Remaining screws, chassis 10 Nm (7.4 lbf ft) Screw, ball joint of push rod on 10 Nm (7.4 lbf ft) Loctite ®...
  • Page 153 TECHNICAL DATA 23 Screw, wheel speed sensor on 4.5 Nm (3.32 lbf ft) axle clamp Nut, pull switch (US) M8x1 0.8 Nm (0.59 lbf ft) Engine attachment bolt 60 Nm (44.3 lbf ft) Remaining nuts, chassis 45 Nm (33.2 lbf ft) Remaining screws, chassis 45 Nm (33.2 lbf ft) Screw, bottom shock absorber...

  • Page 154: 24 Substances

    24 SUBSTANCES Brake fluid DOT 4 / DOT 5.1 Standard/classification – Guideline – Use only brake fluid that complies with the specified standard (see specifications on the container) and that exhibits the corresponding properties. Recommended supplier Castrol – REACT PERFORMANCE DOT 4 ®...
  • Page 155 SUBSTANCES 24 Fork oil (SAE 4) (48601166S1) Standard/classification – SAE ( p. 156) (SAE 4) Guideline – Use only oils that comply with the specified standards (see specifications on the container) and that exhibit the corresponding properties. Shock absorber fluid (SAE 2.5) (50180751S1) Standard/classification –...

  • Page 156: 25 Auxiliary Substances

    25 AUXILIARY SUBSTANCES Air filter cleaner Recommended supplier ® MOTOREX – Racing Bio Dirt Remover Chain cleaner Recommended supplier ® MOTOREX – Chain Clean High viscosity grease Recommended supplier ® – LGHB 2 Long-life grease Recommended supplier ® MOTOREX – Bike Grease 2000 Off-road chain spray Recommended supplier...
  • Page 157 AUXILIARY SUBSTANCES 25 Universal oil spray Recommended supplier ® MOTOREX – Joker 440 Synthetic...

  • Page 158: 26 Standards

    26 STANDARDS JASO T903 MA2 Different technical development directions required a separate specification for motorcycles – the JASO T903 MA2 standard. Earlier, engine oils from the automobile industry were used for motorcycles because there was no separate motorcycle specification. Whereas long service intervals are demanded for automobile engines, the focus for motorcycle engines is on high performance at high engine speeds.

  • Page 159: Index Of Special Terms 27

    INDEX OF SPECIAL TERMS 27 On-board diagnosis Vehicle system, which monitors the specified param- eters of the vehicle electronics...

  • Page 160: 28 List Of Abbreviations

    28 LIST OF ABBREVIATIONS Art. no. Article number circa compare e.g. for example etc. et cetera i.a. inter alia number poss. possibly...

  • Page 161: List Of Symbols 29

    Malfunction indicator lamp lights up/flashes yellow – The OBD has detected an error in the vehicle electronics. Come safely to a halt, and contact an authorized Husqvarna Motorcy- cles workshop. The fuel level warning lamp lights up yellow – The fuel level has reached the reserve mark.

  • Page 162: Index

    INDEX INDEX Chain guide checking ......81 12-V battery Chain tension charging ......109 adjusting .
  • Page 163 INDEX Engine guard Fuse installing ......88 main fuse, changing ....110 removing .
  • Page 164 INDEX Manufacturer warranty ....11 removing ......66 Mapping Service .
  • Page 165 INDEX Tire pressure checking ......104 Traction control activating ......37 Transporting .
  • Page 166 *3402540en* 3402540en 04/2021 Husqvarna Motorcycles GmbH Stallhofnerstraße 3 5230 Mattighofen Austria Photo: Mitterbauer/KISKA, www.husqvarna-motorcycles.com Husqvarna Motorcycles GmbH...

This manual is also suitable for:

Fe 350 eu 2022Fe 350 us 2022F2203v4F2275v5

Table of Contents