Multitech MultiConnect MTS2SA-T User Manual page 113

Example Modem Response and Usage
Example #UD commend response are shown in Table 8-11.
Table 8-11. Completed Data Call, with some errors and rate retrain during the call
Modem Response Line
DIAG <2A4D3263 0=09>
DIAG <2A4D3263 1=06 2=0 3=0>
DIAG <2A4D3263 5="C14513902A"
6="A145">
DIAG <2A4D3263 10=1F 11=0C 12=52>
DIAG <2A4D3263 14=03 15=05 16=10>
DIAG <2A4D3263 20=C 22=780 24=0C80
26=79E0>
DIAG <2A4D3263 21=D 25=1F40 27=DAC0>
DIAG <2A4D3263 30=00 31=03 32=01
33=01>
DIAG <2A4D3263 34=7080 35=CB20>
DIAG <2A4D3263 40=1 41=100>
DIAG <2A4D3263 42=0 43=0>
DIAG <2A4D3263 44=1 45=400>
DIAG <2A4D3263 50=2 51=2>
DIAG <2A4D3263 52=343CC 54=0>
DIAG <2A4D3263 53=7230E6 55=47>
DIAG <2A4D3263 56=29D 58=0001>
DIAG <2A4D3263 58=2A4B 59=0004>
DIAG <2A4D3263 60=51>
Command: +++<CR> Escape Sequence
Values: n/a
Description: When the modem has established a connection and has entered online data mode, it is
possible to break into the data transmission in order to issue further commands to the
modem in an online command mode. This is achieved by the DTE sending to the modem a
sequence of three ASCII characters specified by register S2. The default character is + . The
maximum time allowed between receipt of the last character of the three escape character
sequence from the DTE and sending of the OK result code to the DTE is controlled by the
S12 register.
Multi-Tech Systems, Inc. MultiConnect Serial-to-Serial Adapter User Guide (S000354A)
Chapter 10 − Modem Mode AT Commands, S-Registers, and Result Codes
Description
This is version 0.9
Data Answer signal detected; Data only;
Character async
V.8 Call Menu indicates:
V.8 Joint Menu selects:
Receive level = -31 dBm; transmit level = -12 dBm;
noise level = -82 dBm
Far end echo delay in milliseconds;
Far end echo loss in dB;
Near end echo loss = 16 dB
Transmitter: V.34 training completed;
V.34 carrier frequency = 1920; V.34
symbol rate = 3200; initial transmit rate is 31200 bit/s
Receiver: V.90 training completed;
V.90 symbol rate = 8000;
initial receive rate is 56000 bit/s
No carrier loss events, 3 carrier rate renegotiations
attempted;
1 carrier retrain requested;
1 carrier retrain granted
Final transmit rate is 28800 bit/s;
final receive rate is 52000 bit/s
LAPM negotiation completed; frame size = 256
No error control timeout or link NAKs
V.42bis data compression used;
dictionary size = 1024
Hardware transmit and receive flow control
213964 DTE characters transmitted, w/o underrun
7483622 DTE characters received, 71 characters lost
due to receive data overrun
597 (decimal) frames transmitted, with 1 frame error
10827 (decimal) frames received, with 4 frame errors
Local PC initiated hangup
113