Mitsubishi Electric PURY-M200YNW-A1 Service Handbook page 134

[5-1 Dipswitch Functions and Factory Settings ]
7) Selectable with the function switches SW6-9 and SW6-10.
ON
SW6-9
OFF
Switch
SW4
1-10
SW6-10:
1:ON, 0:OFF
OFF
No.769 1000000011
No.817 1000110011
No.818 0100110011
No.832 0000001011
No.848 0000101011
No.876 0011011011
No.885 1010111011
No.886 0110111011
No.891 1101111011
No.896 0000000111
No.897 1000000111
No.900 0010000111
No.912 0000100111
No.913 1000100111
SW4
1-10
[0:OFF,
1:ON]
No.915 1100100111
(Note 1)
SW6-10:ON
No.916 0010100111
No.918 0110100111
No.921 1001100111
No.922 0101100111
No.933 1010010111
No.934 0110010111
No.935 1110010111
No.956 0111011110
No.958 0111110111
No.982 0110101111
No.997 1010011111
No.1006 0111011111
BS_05_M
ON
Self-diagnosis monitor display (round
type LED) No. 0 to 1023
SW4 function setting mode No. 0 to 1023
Function according to switch setting
Function
OFF (LED3 Unlit)
Self-diagnosis/operation Refer to the following page(s). [10 LED Sta-
monitor tus Indicators]
Test run mode: ON/OFF Stops all ICs
Starts up drive recorder Enabled
Data collection during an
Disabled
error
Cumulative compressor
Retained
operation time deletion
Continuous heating cycle
Disabled
function
High-pressure over-rise
SV2 is used.
backup setting
Fan speed setting at low
outside temperature heat- Refer to Note 8).
ing
Smooth auto-shift startup
Disabled
mode
Clearance of error
OC Retained (IC/OC)
history SW
High sensible heat opera- Depends on the combined setting with No.
tion setting 900 (Note 7)
High sensible heat opera- Depends on the combined setting with No.
tion setting 897 (Note 7)
Pump down function Normal control
Forced defrost (Note 2) Normal control
(E)P200, (E)P250:
Defrost start temperature -10°C [14°F]
(Note 2) (E)P300 - (E)P500:
-8°C [18°F]
Defrost end temperature
7°C [45°F]
(Note 2)
Changes the defrost timer
50 minutes
setting (Note 2)
Temperature unit display °C
Refrigerant amount adjust-
Normal control
ment
Effective only when
TH7 ≤ 5 is true or the
Snow sensor setting
snow sensor contact
input is on.
Continuous fan op-
Snow sensor setting
eration (FAN=50%)
High heating power (at low
Effective
outside temperature)
SV2 control time setting af-
Always ON
ter recovery from defrost
Clear the history of com-
Retained
pleting initial control
Target evaporation tem-
Refer to Note 3).
perature setting
Depends on the combined setting with No.
Multiple-stage low-noise 1006 (Note 6)
setting Depends on the combined setting with 997
(Note 7)
SW6-10
OFF
Self-diagnosis monitor display (7seg
LED) No. 1024 to 2047
Self-diagnosis monitor display (7seg
LED) No. 0 to 1023
Switch setting timing
ON (LED3 Lit)
Anytime after power on
Sends a test-run sig-
Anytime after power on
nal to all IC
Disabled Anytime after power on
Enabled Anytime after power on
Cleared Anytime after power on (OFF → ON)
After being energized and while the compres-
Enabled
sor is stopped
After being energized and while the compres-
LEV9 is used.
sor is stopped
After being energized and while the compres-
sor is stopped
After being energized and while the compres-
sor is stopped
After being energized and while the compres-
Enabled
sor is stopped
Deleted (IC/OC) Anytime after power on (OFF → ON)
Anytime after power on (OFF → ON)
Anytime after power on (OFF → ON)
Pump down opera- After being energized and while the compres-
tion sor is stopped
10 minutes after the completion of defrost op-
Forced defrost starts eration (OFF →ON) or 10 minutes after com-
pressor start-up (OFF → ON)
-5°C [23°F] Anytime after power on
12°C [54°F] Anytime after power on
90 minutes Anytime after power on (OFF →ON)
°F Anytime after power on
Anytime after power on (except during initial
Refrigerant amount
startup/becomes ineffective 90 minutes after
adjust mode
compressor started up.)
Effective when TH7
Anytime after power on
≤ 5 is true
Intermittent fan op-
eration (100% for 5
Anytime after power on
minutes ↔ 0% for 30
minutes)
Ineffective Anytime after power on
After being energized and while the compres-
5 minutes
sor is stopped
After being energized and while the compres-
Cleared sor is stopped
* Effective only OFF to ON
Anytime after power on
After being energized and while the compres-
sor is stopped
After being energized and while the compres-
sor is stopped
3
chapter 5 -