Page 1
Service Manual 020-001790-01 HS Series 2K DWU1612-HS DWU2022-HS...
Page 2
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
Christie recommends a 20 A rated wall breaker for the installation. To ensure safety operation, only use the AC power cord provided with the product or recommended by Christie.
Components must be replaced with exact equivalents. Failure to do so may result in unsafe operation. Servicing live equipment Only Christie qualified technicians who are knowledgeable about the hazards associated with hazardous voltage, ultraviolet exposure, and high temperatures are authorized to assemble, install, and service Christie equipment.
Caution! If not avoided, the following could result in minor or moderate injury. • ELECTRICAL and BURN HAZARD! Use caution when accessing internal components. • Only Christie qualified technicians are authorized to use the tools provided in the toolbox. Laser safety precautions This projector has been classified as Class 1 Laser Product-Risk Group 3 according to the IEC 62471:2006, IEC 60825-1:2014 and IEC 62471-5:2015 standard.
• Possibly hazardous optical radiation emitted from this product. • Only Christie qualified technicians who are knowledgeable about the hazards associated with laser use, high-voltage, and high temperatures generated by the product are authorized to assemble, install, and service the Christie Laser Projection System.
Page 14
Permanent show installations containing Risk Group 3 laser-illuminated projectors must meet the following conditions: • Installed by Christie or by Christie-authorized and trained installers. Refer to the Laser Illuminated Projector - Class 1 Risk Group 3 Installation training (Course code: CF- LIPI- 01) on the http://www.christieuniversity.com site.
• Temporary show installations containing Risk Group 3 laser-illuminated projectors may be installed by Christie or sold or leased only to valid laser light show variance holders (laser light show manufacturers) for image projection applications. Such manufacturers may currently hold a valid variance for production of Class IIIb and IV laser light shows and/or for incorporation of the Risk Group 3 laser-illuminated projectors into their shows.
Do not spill liquids of any kind into the projector. Should an accidental spill occur, immediately unplug the projector and have it serviced by a qualified service technician. Power supplies Power supplies are not serviceable. Never open or attempt to service a power supply. Contact Christie for a replacement. Power cord and attachments Observe the following safety and warning guidelines when maintaining the power cord and attachments.
• To loosen the set screws, turn clockwise. Christie recommends adjusting the set screws 1/4 turns each time. The balance between the set screws is subtle and a small adjustment can make an obvious change on the screen. To perform boresight adjustment, complete the following steps: 1.
5. If the firmware upgrade fails, the projector firmware version remains the same as before. To upgrade the firmware again, repeat step 1 through 4. Consult your Christie dealer for more information when the firmware upgrade failure continuous. HS Series 2K Service Manual—DWU1612-HS,DWU2022-HS 020-001790-01 Rev.
1. Ensure the projector is in a secure position. Christie does not recommend having the projector overhang when replacing the feet, unless the projector is securely positioned. 2. Remove the top cover.
• Do not look into the projector lens when the laser is on. The bright light may result in permanent eye damage. • A Christie qualified technician is required for lens removal and installation. To safely remove and install the lens, complete the following steps.
Page 106
Corporate of ces Worldwide of ces Christie Digital Systems USA, Inc. Australia Germany Republic of South Africa United Kingdom Cypress ph: +61 (0) 7 3624 4888 ph: +49 2161 664540 ph: +27 (0)11 510 0094 ph: +44 (0) 118 977 8000...