Page 1
User Manual 020-001466-06 Christie HS Series 2K D13HD2-HS, D13WU2-HS, D16HD-HS, D16WU- HS, D20HD-HS, D20WU-HS...
Page 2
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
Introduction This manual is intended for Christie qualified installers and trained operators of HS Series 2K projectors—D13HD2-HS, D13WU2-HS, D16HD-HS, D16WU-HS, D20HD-HS, and D20WU-HS. For complete HS Series 2K product documentation and technical support, go to www.christiedigital.com. Safety and warning guidelines Read all safety and warning guidelines before installing or operating the projector.
Caution! If not avoided, the following could result in minor or moderate injury. • ELECTRICAL and BURN HAZARD! Use caution when accessing internal components. • Only Christie qualified technicians are authorized to use the tools provided in the toolbox. Laser safety precautions This projector has been classified as Class 1 Laser Product-Risk Group 3 according to the IEC 60825-1:2014 and IEC 62471-5:2015 standard.
Page 11
• Temporary show installations containing Risk Group 3 laser-illuminated projectors may be installed by Christie or sold or leased only to valid laser light show variance holders (laser light show manufacturers) for image projection applications. Such manufacturers may currently hold a valid variance for production of Class IIIb and IV laser light shows and/or for incorporation of the Risk Group 3 laser-illuminated projectors into their shows.
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. General hazards Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Fire and Shock Hazard To prevent fire or shock hazards, do not expose this product to rain or moisture.
Contact your dealer Record the information about your projector and keep this information with your records to assist with the servicing of your projector. If you encounter a problem with your Christie projector, contact your dealer. Purchase record...
Christie recommends a 20 A rated wall breaker for the installation. To ensure safety operation, only use the AC power cord provided with the product or recommended by Christie.
2. Ensure the lens has been installed in the projector by a Christie qualified service technician. Warning! Failure to comply with the following could result in death or serious injury. • Installing or replacing a lens must be done by a Christie qualified service technician to avoid exposure to dangerous emission levels.
Adjusting the size and position Adjust the projector’s size and position. Christie recommends warming the lens before completing these procedures as focus may change as the lens warms. Setting the image size preset Set the image size preset to display the image in its native resolution or to resize by maximizing the height, width, both height and width, or to the maximum size while keeping the original aspect ratio.
2. Adjust the slider by arrow keys or press ENTER to input the value you selected. 3. After inputting the value, press ENTER to apply. HS Series 2K User Manual — D13HD2-HS, D13WU2-HS, D16HD-HS, D16WU-HS, D20HD-HS, D20WU-HS 020-001466-06 Rev. 1 (12-2022)
Geometry correction Modify the geometry of the display image directly on the projector. Connecting to Christie Twist and Mystique grays out the geometry correction settings on the projector. Uploading warp and blend from Twist and Mystique overwrites the currently applied geometry correction settings.
Properties. The changed name shows on both Twist and the projector. Christie Twist can be upgraded to Twist Premium and Twist Pro that provides more advanced warping features. Refer to the Christie website (www.christiedigital.com) for product information and documentation.
You can set blends on a projector when not using Christie Twist and Mystique. Connecting to Twist and Mystique grays out the blend settings on the projector. Applying blends from Twist and Mystique overwrites the blends directly set on the projectors.
IR remote set to address 0. 10. To match up with the projector address, press PROJ and specific number key. HS Series 2K User Manual — D13HD2-HS, D13WU2-HS, D16HD-HS, D16WU-HS, D20HD-HS, D20WU-HS 020-001466-06 Rev. 1 (12-2022)