Page 1
Installation and Setup Guide 020-001464-06 Christie HS Series 2K D13HD2-HS, D13WU2-HS, D16HD-HS D16WU-HS, D20HD-HS, D20WU-HS...
Page 2
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
Introduction This manual is intended for Christie qualified installers and trained operators of HS Series 2K projectors—D13HD2-HS, D13WU2-HS, D16HD-HS, D16WU-HS, D20HD-HS, and D20WU-HS. For complete HS Series 2K product documentation and technical support, go to www.christiedigital.com. Safety and warning guidelines Read all safety and warning guidelines before installing or operating the projector.
Caution! If not avoided, the following could result in minor or moderate injury. • ELECTRICAL and BURN HAZARD! Use caution when accessing internal components. • Only Christie qualified technicians are authorized to use the tools provided in the toolbox. Laser safety precautions This projector has been classified as Class 1 Laser Product-Risk Group 3 according to the IEC 60825-1:2014 and IEC 62471-5:2015 standard.
Page 8
• Temporary show installations containing Risk Group 3 laser-illuminated projectors may be installed by Christie or sold or leased only to valid laser light show variance holders (laser light show manufacturers) for image projection applications. Such manufacturers may currently hold a valid variance for production of Class IIIb and IV laser light shows and/or for incorporation of the Risk Group 3 laser-illuminated projectors into their shows.
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. General hazards Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Fire and Shock Hazard To prevent fire or shock hazards, do not expose this product to rain or moisture.
Contact your dealer Record the information about your projector and keep this information with your records to assist with the servicing of your projector. If you encounter a problem with your Christie projector, contact your dealer. Purchase record...
• Full HD 3D technology with frame sequential up to 120 Hz • Christie Twist™ and Mystique™ allow for easy and quick blending and warping. Support for Mystique™ camera based alignment system (sold separately) • A wide range of connectivity including HDMI, HDBaseT, and 3D inputs •...
Introduction Product documentation For installation, setup, and user information, see the product documentation available on the Christie Digital Systems USA Inc. website. Read all instructions before using or servicing this product. 1. Access the documentation from the Christie website: •...
Christie recommends a 20 A rated wall breaker for the installation. To ensure safe operation, only use the AC power cord provided with the product or recommended by Christie. See...
360 degree free orientation operation HDBaseT T16A/250V~ When installing the projector in portrait orientation, Christie recommends that the built in keypad and power inputs face upwards. This allows access to the built in keypad and power connections during operation. HS Series 2K Installation and Setup Guide—D13HD2-HS, D13WU2-HS, D16HD-HS, D16WU-HS, D20HD-HS, D20WU-HS 020-001464-06 Rev.
Refer to the installation instructions and safety guidelines provided in the kit (such as Christie One Mount Plus, P/N: 140-117100-XX, or Christie One Aluminum Rigging Frame, P/N: 140-137102-XX).
Warning! If not avoided, the following could result in death or serious injury. • Turn off the projector and remove the power cord, before installing or replacing a lens. Only use the lens compatible with Christie HS Series 2K projectors. 1. Remove the dust cover from the lens opening.
To ensure safe operation, only use the AC power cord provided with the product or recommended by Christie. Connect the AC power cord to the AC inlet on the projector. HS Series 2K Installation and Setup Guide—D13HD2-HS, D13WU2-HS, D16HD-HS, D16WU-HS, D20HD-HS, D20WU-HS 020-001464-06 Rev.
2. Ensure the lens has been installed in the projector by a Christie qualified service technician. Warning! If not avoided, the following could result in death or serious injury. • Installing or replacing a lens must be done by a Christie qualified service technician to avoid exposure to dangerous emission levels.
Calculating the lens offset Adjust the lens offset (shift) to align the image on the screen with half image size. To ensure optimal projector and lens performance, Christie recommends keeping the offset (shift) values within the ranges specified below. •...
• To loosen the set screws, turn clockwise. Christie recommends adjusting the set screws 1/4 turns each time. The balance between the set screws is subtle and a small adjustment can make an obvious change on the screen. To perform boresight adjustment, complete the following steps: 1.
Page 47
Corporate of ces Worldwide of ces Christie Digital Systems USA, Inc. Australia Germany Republic of South Africa United Kingdom Cypress ph: +61 (0) 7 3624 4888 ph: +49 2161 664540 ph: +27 (0)11 510 0094 ph: +44 (0) 118 977 8000...
Need help?
Do you have a question about the HS 2K Series and is the answer not in the manual?
Questions and answers