Page 1
Installation and Setup Guide 020-001449-02 HS Series 4K7-HS/4K10-HS...
Page 2
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
Read all safety and warning guidelines before installing or operating the projector. This projector must be operated in an environment that meets the operating range specification. Use only the attachments and/or accessories recommended by Christie. Use of others may result in the risk of fire, shock, or personal injury.
Caution! If not avoided, the following could result in minor or moderate injury. • ELECTRICAL and BURN HAZARD! Use caution when accessing internal components. • Only Christie qualified technicians are authorized to use the tools provided in the toolbox. Laser safety precautions This product is classified as Class 1 Laser Product-Risk Group 2 according to IEC 60825-1:2014 complies with FDA regulations 21 CFR 1040.10 and 1040.11 as a Risk Group 2, LIP (Laser...
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. General hazards Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Fire and Shock Hazard To prevent fire or shock hazards, do not expose this product to rain or moisture.
Contact your dealer Record the information about your projector and keep this information with your records to assist with the servicing of your projector. If you encounter a problem with your Christie projector, contact your dealer. Purchase record...
A web page using Ethernet, or from a PC or device using a wireless USB dongle (optional) How the projector works The 4K7-HS/4K10-HS projector accepts a variety of input signals for a wide range of commercial projection applications. Designed with solid-state illumination light sources and phosphor technology, the red, green and...
Product documentation For installation, setup, and user information, see the product documentation available on the Christie Digital Systems USA Inc. website at www.christiedigital.com. Read all instructions before using or servicing this product. 1. Access the documentation from the Christie website: •...
• Determine the lens throw ratio. For more information detailing the throw ratio for each lens, refer to the 4K7-HS/4K10-HS Lens Throw Ratios Technical Reference Information (020-102940-XX). • 360 degree free orientation operation...
Refer to the installation instructions and safety guidelines provided in the kit (such as the Christie One Mount Plus, P/N: 140-117100-XX, and Christie One Aluminum Rigging Frame, P/N: 140-137102- XX).
Warning! If not avoided, the following could result in death or serious injury. • Turn off the projector and remove the power cord, before installing or replacing a lens. Only use the lens compatible with Christie 4K7-HS/4K10-HS projectors. 1. Remove the dust cover from the lens opening.
6. Turn the lens counterclockwise by a quarter to release the lens. 7. Gently pull the lens out of the lens holder. Christie recommends covering the lens opening with the dust cover to prevent damage to the projector. 4K7-HS/4K10-HS Installation and Setup Guide 020-001449-02 Rev.
100 VAC, 50/60 Hz, 12 A, 1050 W (rated for Japan) 110-240 VAC, 50/60 Hz, 10 A (rated for Taiwan) For more information detailing the power requirements, refer to the 4K7-HS/4K10-HS Specification Guide (P/N: 020-001452-XX). To safely connect the AC power: 1.
• At +100% offset, all of the image appears above the lens center. The following show the vertical and horizontal image offsets for the 4K7-HS/4K10-HS projectors: • Vertical image offset: 0% Lens center •...
• To tighten the set screws, turn counterclockwise. • To loosen the set screws, turn clockwise. Christie recommends adjusting the set screws 1/4 turns each time. The balance between the set screws is subtle and a small adjustment can make an obvious change on the screen.
Connecting to devices This section covers the information on connecting the 4K7-HS/4K10-HS projector to a computer and video equipment. Connecting to a computer Learn what cables/connectors can be used to connect to various devices. Monitor Desktop Laptop HDBaseT T16A/250V~ Connector name...
Page 41
Corporate of ces Worldwide of ces Christie Digital Systems USA, Inc. Australia Germany Republic of South Africa United Kingdom Cypress ph: +61 (0) 7 3624 4888 ph: +49 2161 664540 ph: +27 (0)11 510 0094 ph: +44 (0) 118 977 8000...