7-1-8: Trigger - Korg M3 Parameter Manual

Program mode
7–1–8: Trigger
7–1
–8a
Here you can set KARMA Module Trigger parameters. In
Program mode, you can use one KARMA Module (Module
[A]).
You can make the following settings.
• Timing correction and latch operation for triggers
• Settings for the envelope generators inside the GE
7–1–8a: Module Parameter-Trigger
Control:
Quantize Trigger
Quantize (correct) the timing of the triggering caused by the
note data or Dynamic MIDI.
On (checked): Trigger timing will be quantized in 16th note
units relative to the basic tempo.
Off (unchecked): Triggering will occur at the moment you
play the keyboard or activate a trigger through Dynamic
MIDI (Prog 7–2–3).
Trigger
Quantize Trig
Quantize Trig
Trigger
Quantize Trig
Quantize Trig
Note: When this is On (checked), triggering at a timing that
is within a 32nd note of the 16th note base value will cause
the playback to begin simultaneously (lower row of the
preceding diagram). If the trigger is later than this, playback
will start at the next 16th note (upper row of the diagram
above).
Update On Release
Allows the release of individual input notes to remove those
notes from the notes going to the GE, thereby changing the
effect to use only those notes still being held.
Off (unchecked): Releasing some notes while holding
others causes no change to the input source material, and
therefore no change in the Generated Effect. This is the most
smooth and natural way, and similar to most advanced
auto-accompaniment keyboards.
88
[Off, On]
KARMA GE Phrase / Pattern
[Off, On]
On (checked): Notes that are released are removed from the
input source material, thereby changing the effect to use
only those notes still being held. This is typically the way
simple arpeggiators work, especially if their latch mode is
7–1
turned off.
–8
Menu
Delay:
Delay Start
Specify the delay from when the trigger (by note data) is
input, until the phrase or pattern starts.
3...4x1: Specify the delay time as a note value interval
relative to the tempo.
Fixed: The delay time will be specified in time units (ms).
Set the time in Delay Start Fixed.
Delay Start Fixed [ms]
This is valid if Delay Start is set to Fixed. Set Delay Start in
ms units. The delay specified here will remaing constant,
even when the tempo is changed.
Note (Trigger/Latch):
Note Trigger
Any (Any Note + Dynamic MIDI): Every note-on will cause
triggering; i.e., each note-on will cause the phrase or pattern
to restart from the beginning.
AKR (1st Note After Key Release + Dynamic MIDI):
Triggering will occur when the first note-on occurs from a
state in which no keys are "on." Triggering will not occur if
even one note is being pressed. By changing the chord you
play on the keyboard while holding at least one note, you
can change the notes of the phrase or pattern without
triggering.
1st (1st Only Until Module Stops + Dynamic MIDI): After
KARMA function is turned on, only the first note-on will
cause triggering. Subsequent note-ons will not cause
triggering. This is useful for drum grooves and phrases
where you do not want subsequent chord changes to restart
the phrase.
Dyn (Dynamic MIDI): Triggering will be produced by
operating the controller specified by Dynamic MIDI (Prog
7–2–3). In this case, note-ons will not cause triggering.
Note: With any of these settings, the trigger will be applied
by operations of the controller specified for Dynamic MIDI
(Prog 7–2–3), if Destination is set to Trigger Notes&Envs,
Trigger Note (see "Dynamic MIDI Sources & Destinations"
on page 601).
Note Latch
Specifies whether the phrase or pattern will continue when
you release your hand from the keyboard (latch on) or
whether the phrase or pattern will stop (latch off). In
Program mode, turn this On (checked) and use the LATCH
switch to control latch on/off.
Off: Latch will be off regardless of the LATCH switch on/off
status.
On: The LATCH switch will control latch on/off. When the
LATCH switch is off (LED dark), latch is off. When the
LATCH switch is on (LED lit), latch is on.
Note: In Combination and Sequencer mode, up to four
KARMA Modules can be used. In these modes, you can turn
Note Latch on/off independently for each KARMA Module.
If you use "Copy KARMA Module" to copy KARMA
Module settings from these modes to a program, there may
be cases in which the setting here will be off, so that latch-on
will not occur even if you turn on the LATCH switch. In
such cases, turn this on.
[Off, Fixed, 3 ...4x1]
[0000...5000]
[Any, AKR, 1st, Dyn]
[Off, On]