Korg M3 Parameter Manual page 414

Media mode
"*" specifies the subsequent characters as a wild card.
"?" specifies only one character as a wild card.
1. If you specify SFX_A* and execute loading, the follow-
ing files will be loaded.
SFX_A_00.WAV
SFX_A_01.WAV
2. If you specify SFX_?_00 and execute loading, the fol-
lowing files will be loaded.
SFX_A_00.WAV
SFX_B_00.WAV
SFX_C_00.WAV
3. If you specify SFX_*_00, the result will be the same as if
you specify "SFX_*", and the following files will be
loaded.
SFX_A_00.WAV
SFX_A_01.WAV
SFX_B_00.WAV
SFX_B_01.WAV
SFX_C_00.WAV
4. If you specify * and execute loading, all of the .WAV
files will be loaded as follows.
PIANO.WAV
SFX_A_00.WAV
SFX_A_01.WAV
SFX_B_00.WAV
SFX_B_01.WAV
SFX_C_00.WAV
24) Load .KSC
The .KMP files and .KSF files listed in the .KSC file will be
loaded as multisamples and samples respectively.
The .KMP files and .KSF files listed in the .KSC
file are saved in a directory of the same name that
is created automatically at the same time as the
.KSC file.
1. Select .KSC Allocation allows you to specify how the
multisamples and samples in the .KSC file will be
loaded.
404
Append: The data will be loaded into the numbers after the
last multisample or sample number currently existing in
sample RAM (i.e., that were previously sampled or loaded).
In this case, only the valid multisamples and samples will be
packed and loaded. (See diagram in ".KSC Allocation" on
page 400)
If "Load ********.PCG too" is checked when you load the
data, programs within the .PCG file that use multisamples
from the .KSC file will automatically have the multisample
settings for their oscillators rewritten so that each program
uses the correct multisample. Drum kits in the .PCG file that
use samples from the .KSC file will automatically have the
sample settings for the drum kit rewritten so that the drum
kit uses the correct samples.
Clear: All multisamples and samples currently existing in
sample RAM will be cleared, and the multisamples and
samples will be loaded in the same configuration as when
they were saved. (See diagram in ".KSC Allocation" on
page 400)
Choose Append if sample RAM already contains
multisamples and samples that you do not want to erase,
and you would like to load additional multisamples and
samples from media.
Choose Clear if you want to reproduce the state in which the
data had been saved, for example immediately after power-
on.
• If the current directory contains a .PCG file, and .SNG
file of the same filename, you can select the "Load
********.PCG too" check box, and the "Load ********.SNG
too" check box. See step 1 of the "1) Load .PCG" on
page 399.
• If you check "Load ********.PCG too," the .PCG file of the
same name as the .KSC file will also be loaded. See step
2 of the "1) Load .PCG" on page 399.
• If you check "Load ********.SNG too," the .SNG file of the
same name as the .KSC file will also be loaded. See step
3 of the "1) Load .PCG" on page 399.
2. To load the data, press the OK button. To cancel with-
out loading, press the Cancel button.
If the .KSF files used by the .KMP file are not in the current
directory or below it, a dialog box will appear, allowing you
to specify the directory. Use the procedure "If a file to be
loaded cannot be found, or when loading a file that was
saved across media" on page 398 to load the required .KSF
files.
Since overflow checking of sample RAM is performed
when loading each individual .KSF file, it is possible
that an overflow may occur in the middle of the loading
process.
25) Load .KMP
The selected .KMP file will be loaded as a multisample. The
.KSF files used by the .KMP will also be loaded as samples.
The .KSF files used by the .KMP file will be saved
in an identically-named directory that is created
automatically when the .KMP file is created.
1. To load the data, press the OK button. To cancel with-
out loading, press the Cancel button.
Samples will be loaded starting at the first unoccupied
number following the last multisample or sample that
currently exists in the sample memory. Only valid
multisamples or samples will be packed and loaded
(Append load).
If the .KSF files used by the .KMP file are not in the current
directory or below it, a dialog box will appear, allowing you
to specify the directory. Use the procedure "If a file to be
loaded cannot be found, or when loading a file that was