Combi P8-2: Ifx; 8-2-1: Routing2 T01-08, 8-2-2: Routing2; T09-16 - Korg M3 Parameter Manual

COMBI P8–2: IFX
8–2–1: Routing2 T01–08,
8–2–2: Routing2 T09–16
8–2
–1a
8–2
–1b
8–2
–1c
8–2
–1d
Here you can specify the program oscillator output bus,
effect control bus, and AUX bus for timbres 1–8 and 9–16.
8–2–1(2)a: Routing Map,
8–2–1(2)b: Combination Name,
8–2–1(2)c: Timbre Info
For more information, please see "8–1–1: Routing1 T01–08,
8–1–2: Routing1 T09–16" on page 177.
8–2–1(2)d: Routing2
Bus Select (IFX/Indiv. Out Assign)
[DKit, L/R, IFX1...5, 1...4, 1/2, 3/4, Off]
This specifies the output bus for the timbre's program
oscillator. This is the same parameter as in the 8–1: IFX-
Routing 1 T01–08 and T09–16 pages.
For more information, please see "Bus Select (IFX/Indiv.
Out Assign)" on page 181.
AUX Bus
These settings send the output of the timbre to the AUX
buses (four mono channels: 1, 2, 3, 4).
The AUX buses are internal buses used for sampling etc. in
each mode.
In Combination mode, you can resample your keyboard or
KARMA performance, or sample an external audio signal
from the Audio Inputs.
Normally you will set Source Bus (Combi 0–7b) to L/R, so
that you can sample the signal of the L/R bus line, such as
your keyboard or KARMA performance.
However, you can use a AUX bus if you want to sample only
an audio input while performing on the keyboard or
KARMA function which are being output via L and R. If
desired, multiple audio inputs can be mixed to a AUX bus,
or the direct signal from an audio input can be mixed to a
AUX bus along with the sound from an insert effect and
sampled. Alternatively, you can resample the keyboard
performance of only specific timbres. For more information,
please see the diagram "Source Bus = AUX 1/2" on page 12.
Off: The signal will not be sent to a AUX bus. Normally you
will leave this off.
1, 2, 3, 4: The output of the timbre will be sent to the
corresponding AUX bus. The Pan setting (Combi 0–3(4)b) of
COMBI P8–2: IFX 8–2–1: Routing2 T01–08, 8–2–2: Routing2 T09–16
8–2
–1
Menu
[Off, 1, 2, 3, 4, 1/2, 3/4]
each timbre will be ignored, and the signal will be sent in
monaural.
1/2, 3/4: The output of the timbre will be sent in stereo to the
corresponding pair of AUX buses. The signal is sent in
stereo to AUX buses 1/2 or 3/4 according to the Pan setting
(Combi 0–3(4)b) of each timbre.
FX Control Bus
Sends the output of the timbre to an FX Control bus (two-
channel mono FX Ctrl 1 or 2).
Use the FX Control buses when you want a separate sound
to control the audio input of an effect. You can use two FX
Control buses (each is a two-channel mono bus) to control
effects in various ways.
For more information, please see "FX Control Buses" on
page 423.
▼8–2–1(2): Menu Command
• 0: Write Combination ☞p.185
• 1: Panel–SW Solo Mode On ☞p.106
• 2: Exclusive Solo ☞p.107
• 3: Copy Insert Effect ☞p.117
• 4: Swap Insert Effect ☞p.118
• 5: DrumKit IFX Patch ☞p.190
For more information, please see "Combination: Menu
Command" on page 185.
[Off, 1, 2]
181