Korg M3 Parameter Manual page 153

control change messages can also be sent to an external
MIDI device using X–Y MIDI Out (Global 1–2a).
Note that, in Combination mode, only the Combi's X–Y CCs
can be sent to external MIDI instruments; the individual
Program's X–Y CCs are only used internally.
Enable CC Control
When this box is checked, the X–Y position will control the
CCs assigned to +X, –X, +Y, and –Y, as set below.
When this box is not checked, the CC assigned to +X, –X,
+Y, and –Y will have no effect, but the MIDI CC numbers
specified by X (X–Y Mode) and Y (X–Y Mode) in Global P2:
Controllers– MIDI CC# Assign can be transmitted and
received.
For more information, please see "X–Y control and MIDI"
on page 142.
This parameter affects only the Combi X–Y CCs. Even if this
is turned Off, the individual Programs' X–Y CCs will still
function normally.
X Mode [Positive, Negative, Xfade, Split]
You can set up the X–Y CCs to send out CCs in several
different patterns, as shown in the graphic below. This
controls the pattern for the X axis. Also, it applies only to the
Combi X–Y CCs, and has no effect on the individual
Program X–Y CCs.
Positive sends out only +X, starting at 0 at the far left, and
increasing to 127 at the far right. –X is disabled in this mode.
Negative sends out only –X, starting at 0 at the far right, and
increasing to 127 at the far left. In this mode, +X is grayed
out.
Xfade sends out both +X and –X, overlapping throughout
the X axis. As one increases, the other decreases.
Split sends out both +X and –X, with a split in the center. +X
is sent when the point moves to the right of the center, and
–X is sent when the point moves to the left of center.
+X
This assigns the controller transmitted by the +X direction.
You can use this as an AMS source to control Program
parameters, or as a Dmod source to control Effects
parameters. It will be grayed out if the X Mode, above, is set
to Negative.
–X
This assigns the controller transmitted by the –X direction. It
will be grayed out if the X Mode, above, is set to Positive.
The selections are the same as for +X, above.
COMBI P1: DT/XY/Ctrls 1–4: X–Y CC T01–08, 1–5: X–Y CC T09–16
[Off, On]
[Off...MIDI CC#119]
[Off...MIDI CC#119]
X–Y CC Modes
Positive
Generates only +X,
increasing from left to right.
0 +X CC 127
–127 0 +127
X-Axis
Xfade
Generates both +X and –X.
One increases as the other
decreases.
0 +X CC 127
127 –X CC 0
–127 0 +127
X-Axis
Y Mode [Positive, Negative, Xfade, Split]
This controls the X–Y CC pattern for the Y axis. For more
information, please see the description under X Mode,
above.
+Y
This assigns the controller transmitted by the +Y direction. It
will be grayed out if the Y Mode, above, is set to Negative.
The selections are the same as for +X, above.
–Y
This assigns the controller transmitted by the –Y direction. It
will be grayed out if the Y Mode, above, is set to Positive.
The selections are the same as for +X, above.
X–Y Graphic:
X–Y Graphic
The X–Y graph shows a representation of the volume
change when using Equal Power mode or the Center
Volume setting.
Timbre Select
This selects the timbre whose data will be shown in the X–Y
graph.
1–4(5)b: Timbre Info
Selected Timbre Info:
Timbre Number:
Timbre Category:
For more information, please see "1–2(3)c: Timbre Info" on
page 141.
Negative
Generates only –X,
increasing from right to left.
127 –X CC 0
–127 0 +127
X-Axis
Split
Generates both +X and –X.
Both are 0 in the center.
+X increases to the right;
–X increases to the left.
+X CC
0 127
127 0
–X CC
–127 0 +127
X-Axis
[Off...MIDI CC#119]
[Off...MIDI CC#119]
[01...16]
143